I often use old chips at work, such as MT8972, MT8952, etc. There are many chips with problems, which often cause the circuit board to not work properly. Could any expert give me a test method that ca...
[i=s]This post was last edited by rain_noise on 2015-4-16 10:16[/i] [p=30, 2, left]I registered on the Ti official website using my company email address. I had always applied for samples smoothly in ...
[i=s] This post was last edited by helloxieyu on 2015-8-21 10:03 [/i] [b]The huge error of the MSP430 internal temperature sensor: [/b] According to the manual, the ADC voltage is equivalent to 3.55mV...
I use VS 2005 to develop Wince using WTL library. When I do remote debugging, the picture display fails. When I do single-step debugging, I find that CBitmap bmp; bmp.LoadBitmap(IBD_BACKGROUND); does ...
This is my first time using F28069. I made a circuit board and encountered a problem. My F28069, the XRS pin is always low level after power on? I directly connected a pull-up resistor, but it is stil...
International Solar Photovoltaic Network News: Chinese inverter company Sungrow announced that it will build a 3GW photovoltaic inverter manufacturing plant in Bangalore, the capital of Karnataka, ...[Details]
When talking about Chinese chips, Ni Guangnan is indispensable. Let’s learn more about the relevant content with the embedded editor.
Since he co-founded Lenovo in 1985, Ni Guangnan has been s...[Details]
Profit growth of 85% in 2017, target revenue of 12.5 billion yuan in 2018: The company released its 2017 annual report, achieving revenue of 8.886 billion yuan, a year-on-year increase of 48.01%; prof...[Details]
In the war without gunpowder between China and the United States,
ZTE
has become a new victim. The seven-year chip ban by the United States has pushed this communications giant to a life-or...[Details]
In the actual project development process, hardware circuits often need to be modified, and the modified parts need to modify the driver. Thinking about the coming and going of such requirements is t...[Details]
The program got stuck during LCD initialization. Through hardware debugging, it was found that it was stuck in the Delay_ms() function. Going to the definition, it was found to be a macro definition ...[Details]
After searching a lot of information, I finally understood the time base timer. I did not use any library functions but operated the registers directly. The following introduces the systick in STM32...[Details]
China Energy Storage Network News:
The State Grid Corporation of China, this elephant, is planning to turn around and enter the emerging power service market.
The rallying cry for the tr...[Details]
Artificial Intelligence (AI) is undoubtedly the hottest topic in the technology industry in the past one or two years. In addition to the huge investments made by technology giants, financial and o...[Details]
This small program is still the use of timer, which is relatively simple. The specific parts are noted in the comments, please refer to the comments. /*********************************************...[Details]
With the development of information technology, intelligence, informatization and networking have become the development trend of modern industrial control. Since the 1980s, the rapid development...[Details]
With the large-scale development of the domestic household photovoltaic market and the improvement of component and inverter technology, the system cost has dropped significantly in the past year. The...[Details]
On May 16, in response to
the public opinion storm caused by
Lenovo's
"
5G
voting" incident,
Lenovo
Holdings Chairman and
Lenovo
Group Founder Liu Chuanzhi, Lenovo Gr...[Details]
I encountered a problem when debugging the STM32 system clock setting: TIM2 timing 1Ms, TIM2 interrupt service function time++, LED state changes when time=100. After the program runs, I found that t...[Details]
1) ADC multi-channel acquisition: (Multi-channel acquisition must use scanning mode. In scanning mode, the channels of the rule group share a register, so DMA transmission must be used; to prevent da...[Details]