EEWORLDEEWORLDEEWORLD

Part Number

Search

GUB-GL8A-03-3201-C-

Description
Array/Network Resistor, Isolated, Thin Film, 0.16W, 3200ohm, 0.25% +/-Tol, -25,25ppm/Cel, 4430,
CategoryPassive components    The resistor   
File Size493KB,3 Pages
ManufacturerTT Electronics plc
Websitehttp://www.ttelectronics.com/
Download Datasheet Parametric View All

GUB-GL8A-03-3201-C- Overview

Array/Network Resistor, Isolated, Thin Film, 0.16W, 3200ohm, 0.25% +/-Tol, -25,25ppm/Cel, 4430,

GUB-GL8A-03-3201-C- Parametric

Parameter NameAttribute value
Is it Rohs certified?incompatible
Objectid795554787
package instructionSMT, 4430
Reach Compliance Codecompliant
Country Of OriginUSA
ECCN codeEAR99
YTEOL7.1
structureMolded
Network TypeIsolated
Number of terminals16
Maximum operating temperature125 °C
Minimum operating temperature-55 °C
Package height2.667 mm
Package length11.176 mm
Package formSMT
Package width7.544 mm
Rated power dissipation(P)0.16 W
resistance3200 Ω
Resistor typeARRAY/NETWORK RESISTOR
seriesGUB
size code4430
technologyTHIN FILM
Temperature Coefficient25 ppm/°C
Tolerance0.25%
TaNFilm
®
Small Outline Surface
Mount Resistor Network
GUB Series
Thin film on ceramic technology
0.220” and 0.300” sizes available
RoHS compliant version available
DESC 87012 and 87013 available
Standard JEDEC packages for automatic placement equipment
Compliant leads to
compensate for
thermal expansion
and contractions.
IRC Advanced Film Division
Ultra precision tantalum
nitride resistance element
on high purity alumina.
Rugged, molded
construction.
IRC’s TaNFilm®, Small Outline Integrated Circuit resistor networks are ideally suited for surface mounting.
The 0.05 inch lead spacing provides higher lead density, increased component count, lower installed resistor
cost, and better reliability. They are ideally suited for the latest surface mount assembly techniques, and each
lead can be 100% visually inspected. The compliant leads relieve thermal expansion and contraction stressed
created by soldering and temperature excursions.
The tantalum nitride film system provides precision tolerance, exceptional TCR tracking, and low noise.
TaNFilm® provides stability, high reliability, and long life characteristics. Testing has demonstrated performance
exceeding MIL-PRF-83401 characteristics H.
Electrical Data
GM Type
Resistance Range (Ω)
GL Type
Absolute Tolerance
Ratio Tolerance To R1
TCR (ppm/°C)
TCR Tracking To R1 (ppm°C)
Operating Temperature Range
Noise
Substrate
Custom circuits and special testing available.
Schem A: 10 to 200K
Schem B: 10 to 1000K
Schem A: 10 to 150K
Schem B: 10 to 75K
Available to ±0.1%
Available to ±0.05%
±25, ±50, ±100
±5
-55°C to +125°C
Less than -25 dB
High purity alumina substrate
General Note
IRC reserves the right to make changes in product specification without notice or liability.
All information is subject to IRC’s own data and is considered accurate at time of going to print.
© IRC Advanced Film Division
• 4222 South Staples Street • Corpus Christi Texas 78411 USA
Telephone: 361 992 7900 • Facsimile: 361 992 3377 • Website: www.irctt.com
A subsidiary of
TT electronics plc
GUB Series Issue November 2008 Sheet 1 of 3
SPI clock control problem
I am going to make a chip ADS8320 recently, which needs to use SPI. This chip has only three pins connected to STM32, namely CLK, MISO, CS, but no MOSI pin. Its operation needs the clock of the host t...
肌肉熊 stm32/stm8
Problems with charging mobile phone batteries with DC power supply
[i=s] This post was last edited by jameswangsynnex on 2015-3-3 20:00 [/i] If I use a DC power supply to charge a mobile phone battery, what voltage should I use and how long should it take to charge? ...
zjjone1023 Mobile and portable
MSP430 clock system!
I didn’t go into it in depth for a while, I just watched the routine and used it twice!I had nothing to do at home on the weekend, so I took a good look at the MSP430 clock system! It feels very flexi...
乌合之众 Microcontroller MCU
HMI Topic 1 What is HMI?
For many years, the demon beast HMI has been causing chaos in the human world, confusing people's vision and hearing!Almost no one knows when it entered the human world?According to various secret boo...
蓝色心情 DSP and ARM Processors
How about using KSZ8041FTL for optical PHY when connecting STM32F107 to fiber optic module? Has anyone used it?
I used STM32F107+DP89848+OCM2521 to build a fiber optic Ethernet. OCM2521 is a 100M multimode fiber optic module with a voltage level of 3.3v (LVPECL), but it didn't work. The loopback test was succes...
vikione stm32/stm8
Help stm32 short circuit
This is my first time making an STM32 board, model F103ZET6. After the PCB arrived, I soldered the STM32 to the board. Because the DCDC chip had not arrived yet, I brought out the SWD interface, used ...
jaccopa stm32/stm8

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 441  710  757  341  2639  9  15  16  7  54 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号