Y0110569K000T19L datasheet, PDF

Datasheet> All Categories > Passive components> The resistor> Y0110569K000T19L

Y0110569K000T19L: DescriptionFixed Resistor, Metal Foil, 2.5W, 569000ohm, 600V, 0.01% +/-Tol, -2,2ppm/Cel,; CategoryPassive components The resistor; File Size112KB，6 Pages; ManufacturerVishay; Websitehttp://www.vishay.com; Environmental Compliance

Download Datasheet Parametric View All

Y0110569K000T19L Overview

Fixed Resistor, Metal Foil, 2.5W, 569000ohm, 600V, 0.01% +/-Tol, -2,2ppm/Cel,

Y0110569K000T19L Parametric

Parameter Name	Attribute value
Is it Rohs certified?	conform to
Objectid	977978650
Reach Compliance Code	unknown
structure	Hermetically Sealed
JESD-609 code	e3
Lead diameter	0.64 mm
Lead length	25.4 mm
Number of terminals	2
Maximum operating temperature	125 °C
Minimum operating temperature	-55 °C
Package diameter	12.7 mm
Package length	38.1 mm
Package form	Axial
method of packing	Bulk
Rated power dissipation(P)	2.5 W
resistance	569000 Ω
Resistor type	FIXED RESISTOR
series	H SERIES-AXIAL
technology	METAL FOIL
Temperature Coefficient	2 ppm/°C
Terminal surface	Tin (Sn)
Tolerance	0.01%
Operating Voltage	600 V

Preview

Download Datasheet

View All

H Series

Vishay Foil Resistors

New Generation of Secondary Standards Hermetically Sealed High Precision Bulk

Metal

Foil Technology Resistors with TCR of ± 2 ppm/°C, Tolerance of ± 0.001 % and

Load Life Stability of ± 0.005 % (Metrology, Laboratory, Instrumentation, Industrial)

FEATURES

•

Temperature coefficient of resistance (TCR):

± 2 ppm/°C typical (- 55 °C to + 125 °C, + 25 °C

ref.).

For

ultra

high

performances

(instrumentation and metrology) please refer to

the last page

•

Resistance range: 5

to 1.84 MΩ (higher or

lower values of resistance available)

•

Vishay Foil resistors are not restricted to standard values;

specific “as required” values can be supplied at no extra

cost or delivery (e.g. 1K2345 vs. 1K)

•

Power rating: 0.3 W to 2.5 W at + 25 °C (depending on

model - see table 2)

•

Tolerance: to ± 0.001 % (10 ppm)

•

Load life stability to ± 0.002 % (20 ppm) at 25 °C, 2000 h

at rated power

•

Load life stability can be considerably improved

through in-house stabilization

•

Shelf life stability: ± 2 ppm for at least 6 years

(unaffected by humidity)

•

Electrostatic discharge (ESD) up to 25 000 V

•

Rise time: 1 ns effectively no ringing

•

Thermal stabilization time < 1 s (nominal value achieved

within 10 ppm of steady state value)

•

Current noise: 0.010 µV

RMS

/V of applied voltage (< - 40 dB)

•

Thermal EMF: 0.05 µV/°C typical

•

Voltage coefficient: < 0.1 ppm/V

•

Non-inductive: < 0.08 µH

•

Non-inductive, non-capacitive design

•

Non hot spot design

•

Terminal finish available: lead (Pb)-free or tin/lead alloy

•

Impervious to harmful environments - oil-filled

•

Compliant to RoHS directive 2002/95/EC

•

Prototype quantities available in just 5 working days

or sooner. For more information, please contact

foil@vishay.com

•

For better performances (values, TCR, tolerance, stability),

please see the HZ series

INTRODUCTION

The H series resistors are oil-filled, hermetically sealed ultra

precision resistors and are used as secondary standards for

metrology applications.

The hermetic sealing eliminates the ingress of moisture and

oxygen, while the oil acts as a thermal conductor, thus

eliminating the long-term degradation elements of unsealed

resistors, while at the same time allowing the device to

accept short periods of overload without degradation.

Vishay’s Bulk Metal

Foil outperforms all other resistor

technologies available today for applications that require

precision and stability. When combined with the hermetic

sealing and oil filling, the H series resistors become

the most

precise and stable resistors available.

With accuracies of 0.001 %, a resistance range from 5

to 1.84 MΩ, and long term shelf life of less than 2 ppm,

these devices are virtually secondary standards that can be

carried in sets for daily or periodic calibration of factory

measurement equipment.

The H series is available with laboratory and metrology

level precision and long-term stability with additional

in-house oriented processes such as: chip stabilization,

special TCR plotting, additional treatments for ultra

stability and special post manufacturing operations

(PMO). (Please refer to the last page)

TABLE 1 - TCR VS. RESISTANCE VALUE

RESISTANCE

VALUE (Ω)

100 to < 1M84

50 to < 100

5 to < 50

TYPICAL TCR AND MAX. SPREAD

(- 55 °C to + 125 °C, + 25 °C ref.)

(ppm/°C)

± 2 ± 2.5

± 2 ± 3.5

± 2 ± 4.5

FIGURE 1 - SHELF LIFE - VHA518-11

12K9 VS. QHE

0.9

0.8

0.7

0.6

0.5

0.4

0.3

0.2

0.1

- 0.1

100 200 300 400 500 600 700 800 900 1000

Note

• For maximum TCR < 1 ppm/°C, see VHP100 and contact

application engineering

* Pb containing terminations are not RoHS compliant, exemptions may apply

Resistance Change (ppm)

Time (Days)

Document Number: 63006

Revision: 07-Dec-09

For any questions, contact:

foil@vishay.com

www.vishay.com

Recommended Resources

Main circuit of KZS10 series thyristor rectifier device

Low dropout three-terminal voltage regulator MC33269 circuit diagram

Motor Speed Control Circuit Using AC Tachometer Sensor

High frequency astable circuit

875p computer motherboard circuit diagram_093

Computer motherboard circuit diagram 440BX_11

Has anyone tried to switch STM8 to lsi? What is the power consumption?: To reduce the standby current, do nothing. The chip is STM8A5189, and now it can reach 3 to 4 mA. I wonder if anyone has tried it. What is the theoretical value?...; wangkj22 stm32/stm8

What are the differences among the many “grounds” in electronic technology?: XGND is the abbreviation of the wire end. It stands for the ground or zero line. GND (Ground) on the circuit diagram and the circuit board stands for the ground or zero line. GND means the common end,...; fish001 Analogue and Mixed Signal

How to connect MSP430 to computer?: How do I connect MSP430 to a computer? How do I download code to the microcontroller? Help!...; evahiay Microcontroller MCU

pl2303 driver under CE6: Hello everyone, I bought a USB to serial GPS receiver, which uses a pl2303 conversion chip inside. It converts the serial port to USB. But under the CE6 system, I can't install the driver and can't us...; guanliheng Embedded System

Is it possible for the LDO or DCDC output voltage to be lower than the internal reference voltage?: Generally, the output voltage of the regulator is divided by a resistor and compared with the internal reference voltage. Thereby adjusting the output voltage to reach the desired voltage value. Howev...; sfcsdc Analog electronics

Mi Rabbit Building Block Robot Unboxing: [i=s]This post was last edited by supermiao123 on 2016-11-16 10:11[/i] [url=http://www.mi.com/toyblock/?cfrom=search]http://www.mi.com/toyblock/?cfrom=search[/url] I'll post a URL first. I saw a new p...; supermiao123 Robotics Development

Shortcut: S0 S1 S2 S3 S4 S5 S6 S7 S8 S9 SA SB SC SD SE SF SG SH SI SJ SK SL SM SN SO SP SQ SR SS ST SU SV SW SX SY SZ T0 T1 T2 T3 T4 T5 T6 T7 T8 T9 TA TB TC TD TE TF TG TH TI TJ TK TL TM TN TO TP TQ TR TS TT TU TV TW TX TY TZ U0 U1 U2 U3 U4 U6 U7 U8 UA UB UC UD UE UF UG UH UI UJ UK UL UM UN UP UQ UR US UT UU UV UW UX UZ V0 V1 V2 V3 V4 V5 V6 V7 V8 V9 VA VB VC VD VE VF VG VH VI VJ VK VL VM VN VO VP VQ VR VS VT VU VV VW VX VY VZ W0 W1 W2 W3 W4 W5 W6 W7 W8 W9 WA WB WC WD WE WF WG WH WI WJ WK WL WM WN WO WP WR WS WT WU WV WW WY X0 X1 X2 X3 X4 X5 X7 X8 X9 XA XB XC XD XE XF XG XH XK XL XM XN XO XP XQ XR XS XT XU XV XW XX XY XZ Y0 Y1 Y2 Y4 Y5 Y6 Y9 YA YB YC YD YE YF YG YH YK YL YM YN YP YQ YR YS YT YX Z0 Z1 Z2 Z3 Z4 Z5 Z6 Z8 ZA ZB ZC ZD ZE ZF ZG ZH ZJ ZL ZM ZN ZP ZR ZS ZT ZU ZV ZW ZX ZY

Popular Components