DCT4E407X0035DF datasheet, PDF

Datasheet> All Categories > Passive components> capacitor> DCT4E407X0035DF

DCT4E407X0035DF: DescriptionTantalum Capacitor, Polarized, Tantalum (wet), 35V, 20% +Tol, 20% -Tol, 400uF, Through Hole Mount, AXIAL LEADED, ROHS COMPLIANT; CategoryPassive components capacitor; File Size3MB，9 Pages; ManufacturerEXXELIA Group; Environmental Compliance

Download Datasheet Parametric View All

DCT4E407X0035DF Overview

Tantalum Capacitor, Polarized, Tantalum (wet), 35V, 20% +Tol, 20% -Tol, 400uF, Through Hole Mount, AXIAL LEADED, ROHS COMPLIANT

DCT4E407X0035DF Parametric

Parameter Name	Attribute value
Is it Rohs certified?	conform to
Objectid	2099016236
package instruction	,
Reach Compliance Code	unknown
capacitance	400 µF
Capacitor type	TANTALUM CAPACITOR
dielectric materials	TANTALUM (WET)
leakage current	0.008 mA
Installation features	THROUGH HOLE MOUNT
negative tolerance	20%
Number of terminals	2
Maximum operating temperature	125 °C
Minimum operating temperature	-55 °C
Package shape	TUBULAR PACKAGE
polarity	POLARIZED
positive tolerance	20%
Rated (DC) voltage (URdc)	35 V
ripple current	750 mA
surface mount	NO
Delta tangent	0.28
Terminal shape	WIRE

Preview

Download Datasheet

View All

GENERAL INFORMATION

MANUFACTURING

ANODE AND INSULATOR

Tantalum capacitors have the highest ratio of capacitance per volume.

This is mainly due to the high dielectric constant of its insulator and to its large

surface area.

The basic raw material is a high purity (greater than 99.99%) tantalum powder

with a very fine granulation, compressed to form a cylinder or a parallelepiped

constituting the anode of the capacitor (positive plate).

The pellet is then sintered at high temperature (1500 to 2000°C), under hard

vacuum (10

-6

torr), firstly to purify the powder and secondly to obtain a strong

mechanical structure by welding of the particles.

The insulating part is obtained by anodization to a depth of the tantalum surface

which forms a tantalum pentoxide film (Ta

) with a thickness of about 16

angstroms per anodization volt. The dielectric constant is between 21 and 27,

depending upon the anodization conditions.

TYPE IDENTIFICATION – ORDERING INFORMATION

THE COMPLETE IDENTIFICATION OF A PRODUCT IS MADE UP OF:

• Type (or model)

• Tolerance

• Testing parameters (standard cata-

log part vs. tested in accordance

with MIL-SPEC standards)

• Rated capacitance

• Rated voltage

• Case size

• RoHS or non-RoHS

• For solid tantalum capacitors

specify tape or bulk packaging

THE TYPE

It identifies the basic capacitor (DCTSXX).

Example: DCTS1

THE RATED CAPACITANCE

Expressed in picofarads, the first two digits are significant figures; the third is the

number of zeros following:

Example: 102 = 10 x 10

pF = 0.001 µF

103 = 10 x 10

pF = 0.01 µF

334 = 33 x 10

pF = 0.33 µF

THE TOLERANCE

It can be expressed directly in % or identified by a code letter:

X0 = ±20% X9 = ±10% X5 = ±5%

Note:

The standard tolerance for tantalum capacitors is ±20%; if no tolerance

is given, it is considered as 20%. A 20% tolerance means in fact -20%

to +20% of the nominal value.

THE RATED VOLTAGE

It is expressed directly in volts (V), with three significant figures.

Example: 006 = 6 V DC; 050 = 50 V DC; 100 = 100 V DC

The case size:

It is indicated on the technical data sheets following the voltage

value and is generally identified by a letter code. It is important to give this

information because there can be, for the same type, a standard range and an

extended range in which the same value will be available in two different sizes.

THE TESTING PARAMETERS

C indicates a standard catalog part and S indicates tested in accordance with

MIL-SPEC standards.

ORDERING INFORMATION EXAMPLE

Part Number = DCTS1105X9040AC

Type: DCTS1

Capacitance = 1 µF

Tolerance = +/-10%

Voltage = 40 V DC

Case Size = A

C indicates standard catalog part

F indicates RoHS part

T indicates non-RoHS part

S indicates screened according to MIL

SOLID ELECTROLYTE: CATHODE AND ENCAPSULATION

The cathode is formed by manganese dioxide which is a grey semi-conductor.

It is obtained by dipping the pellets into a manganese nitrate water solution

which impregnates the internal structure; this solution is then decomposed in a

high temperature oven to obtain manganese dioxide. This operation is repeated

several times. The nature and quality of this semi-conductor greatly influence

the electrical parameters (especially the series resistance).

To finish the negative plate, a graphite coating and then a silver coating are

deposited on the outside surface of the manganese dioxide.

The positive nickel lead is welded on the tantalum wire and the negative lead

is either soldered with wire leads, or pasted with a silver epoxy for surface

mount models.

WET ELECTROLYTE: CATHODE AND ENCAPSULATION

The cathode (for wet tantalum capacitors) is formed by a sulphuric acid solution.

The anodized tantalum pellet is impregnated with this solution and then placed

in a silver or tantalum case, into which some equivalent gelled solution has been

previously deposited.

The case is then crimped on the internal PTFE bush to create the sealing. The

final steps are either the soldering of a glass metal seal, or the crimping of an

elastomer seal on the top of the case.

BURN-IN - SORTING - INSPECTION

All the products are then submitted to a final burn-in, with differing severities

depending upon the required characteristics of each type (temperature, voltage,

time,etc.).

Sorting, marking and inspection operations follow. These procedures are the

same for approved and non-approved parts (with exception of periodic testing).

Recommended Resources

Telephone connect hold key circuit

Electronic relay driving glow digital tube

Parameter table of PT2262-IR

NORELCO rechargeable electric shaver circuit

Computer motherboard circuit diagram 430TX_13

Computer motherboard circuit diagram 815 4_14

Devices supporting the Matter 1.0 standard are coming soon: With the Matter SDK making great progress, developers are now focusing on code quality, stability, and cleanup. This includes work in several key areas of the specification, such as access control cap...; alan000345 RF/Wirelessly

3.5V to 18V input, 3V or 5V output solution help?: What is a good solution for a power input of 3.5V to 18V and an output of 3V or 5V? What kind of power chip should I choose?...; neuopenli Integrated technical exchanges

Oh my god, Michael Jackson died on the 26th of cardiac arrest: Although I don't like him very much, I still remember that in high school, everyone was proud to learn his dance steps. What's more, there was a boy who learned it to perfection and was hailed as a my...; 绿茶 Talking

Come in, please: When soldering the circuit board, are all the ports connected to the power supply connected to the power supply? What about the ground connection?...; melon_1 51mcu

[help]iSCSI: Is there anyone who can guide me? I am a novice and I want to make iSCSI virtual disks, like iscsi cake, ccdisk, inetdisk, starwind. Where should I start? What should I learn?...; feichong Embedded System

msp430 smart desk lamp: Is there any expert who can give me some advice? I am very confused...Use msp430 to design and make an intelligent desk lamp that can automatically adjust the brightness of the desk lamp according to ...; 陆炳贤 MCU

Shortcut: 00 01 02 03 04 05 06 07 08 09 0A 0C 0F 0J 0L 0M 0R 0S 0T 0Z 10 11 12 13 14 15 16 17 18 19 1A 1B 1C 1D 1E 1F 1H 1K 1M 1N 1P 1S 1T 1V 1X 1Z 20 21 22 23 24 25 26 27 28 29 2A 2B 2C 2D 2E 2F 2G 2K 2M 2N 2P 2Q 2R 2S 2T 2W 2Z 30 31 32 33 34 35 36 37 38 39 3A 3B 3C 3D 3E 3F 3G 3H 3J 3K 3L 3M 3N 3P 3R 3S 3T 3V 40 41 42 43 44 45 46 47 48 49 4A 4B 4C 4D 4M 4N 4P 4S 4T 50 51 52 53 54 55 56 57 58 59 5A 5B 5C 5E 5G 5H 5K 5M 5N 5P 5S 5T 5V 60 61 62 63 64 65 66 67 68 69 6A 6C 6E 6F 6M 6N 6P 6R 6S 6T 70 71 72 73 74 75 76 77 78 79 7A 7B 7C 7M 7N 7P 7Q 7V 7W 7X 80 81 82 83 84 85 86 87 88 89 8A 8D 8E 8L 8N 8P 8S 8T 8W 8Y 8Z 90 91 92 93 94 95 96 97 98 99 9A 9B 9C 9D 9F 9G 9H 9L 9S 9T 9W

Popular Components