FMXMA218IKD-08.000000M datasheet, PDF

Datasheet> All Categories > Passive components> Crystal/resonator> FMXMA218IKD-08.000000M

FMXMA218IKD-08.000000M: DescriptionParallel - Fundamental Quartz Crystal, 8MHz Nom, ROHS COMPLIANT, HC-49/U, 2 PIN; CategoryPassive components Crystal/resonator; File Size101KB，1 Pages; ManufacturerFrequency Management International; Environmental Compliance

Download Datasheet Parametric View All

FMXMA218IKD-08.000000M Overview

Parallel - Fundamental Quartz Crystal, 8MHz Nom, ROHS COMPLIANT, HC-49/U, 2 PIN

FMXMA218IKD-08.000000M Parametric

Parameter Name	Attribute value
Is it lead-free?	Lead free
Is it Rohs certified?	conform to
Objectid	1311836810
package instruction	ROHS COMPLIANT, HC-49/U, 2 PIN
Reach Compliance Code	compliant
Ageing	5 PPM/YEAR
Crystal/Resonator Type	PARALLEL - FUNDAMENTAL
Drive level	50 µW
frequency stability	0.01%
frequency tolerance	40 ppm
load capacitance	8 pF
Installation features	THROUGH HOLE MOUNT
Nominal operating frequency	8 MHz
Maximum operating temperature	50 °C
Minimum operating temperature	-10 °C
physical size	L11.05XB4.65XH10.82 (mm)/L0.435XB0.183XH0.426 (inch)
Series resistance	35 Ω
surface mount	NO

Preview

Download Datasheet

View All

FMXMA

SERIES

Microprocessor Crystals

Low Cost Crystals

Thru-Hole Package

Multiple Package Heights

Surface Mount Lead Forming

HC-49/U

SPECIFICATIONS

08 - Issue 4 - 071508

Parameter

Frequency Range

Operation Mode

Load Capacitance (CL)

Frequency Tolerance

Temperature Tolerance

Operating Temperature

Storage Temperature

Equivalent Series Resistance (ESR)

Shunt Capacitance (C0)

Drive Level

Aging @ 25°C

All specifications subject to change without notice.

Specification

1.8 - 180 MHz

See Operation Mode and ESR Table

18 pF Std., 8 to 60 pF and Series available

±30 ppm @ 25°C Std. (See Cal. Tol. for Options)

±50 ppm Std. (See Temp. Tol. for Options)

0 to +70°C Std. (See Temp. Range for Options)

-55 to +125°C

See Operation Mode and ESR Table

7 pF max.

μW

typical, 1 mW max.

±5 ppm per year max.

HC-49/U

0.017

(0.43)

DIA.

0.500

(12.7)

MIN.

0.192

(4.88)

OPERATION MODE AND ESR TABLE

Frequency (MHz)

1.8 - 1.9

2.0 - 2.3

2.4 - 2.9

3.0 - 3.6

3.7 - 4.1

4.2 - 4.8

4.9 - 5.9

6.0 - 7.9

8.0 - 9.9

10.0 - 27.0

24.0 - 29.0

30.0 - 80.0

50.0 - 99.0

100.0 - 180.0

Mode

Fundamental

3rd Overtone

5th Overtone

Max. ESR (Ohms)

650

550

350

200

100

110

0.183

(4.65)

MAX.

STANDARD MARKING

XXX.XXXM

XXXXXXX

FMI YYWW

XXX.XXXM FREQUENCY in MHz

XXXXXXX Part Number

FMI, Date Code

0.435

(11.05)

DIMENSION “H” TABLE

Package

Max. Height

0.530” (13.46mm)

0.426” (10.82mm)

NOTE: Standard Specifications for product indicated in

color

Dimensions:

Inches

(mm)

PART DESCRIPTION SYSTEM

MARKING: See Page 52, Format A

FMXM A1 1 18 H J A - XX.XXXXXXM - CM

Options

Product Family

MicroP Crystal

Package

or A2

Mode

1 - Fundamental

3 - 3rd Overtone

5 - 5th Overtone

Load Cap. (CL)

18 - Standard (pF)

00 - Series

## - Custom (pF)

Cal. Tol. @ 25°C

G ±25 ppm

H ±30 ppm

I ±40 ppm

J ±50 ppm

K ±100 ppm

X Custom

Temp. Tol.

G ±25 ppm

H ±30 ppm

I ±40 ppm

J ±50 ppm

K ±100 ppm

X Custom

Frequency (MHz)

Temp. Range

A 0 to 70 °C

B -20 to 70 °C

C -40 to 85 °C

D -10 to 50 °C

E -10 to 60 °C

F -30 to 60 °C

J 0 to 50 °C

X Custom

TR - Tape & Reel

BI - Base Insulator

GB - Gnd Lead Base

GT - Gnd Lead Top

LT - Lead Trimming

LF - Lead Forming

PD - Parameter Data

TD - Temp. Data

TG - Temp. Grading

CM - Custom Mark

BLANK - None Req’d.

-55°C TO +125°C Available, Limited Stability Options,

please consult the factory.

1-800-800-XTAL

[9825]

www.fmi-inc.com

Recommended Resources

NE555 typical application circuit diagram (2)

Simple four-speed dimmer switch circuit

Automatic water inlet control circuit

Single tone burst circuit for microphone

Human body sensor light circuit

point signal generator

Introduction of Schottky diode used as AND gate or OR gate: Schottky diode used as AND gate As shown in the figure below, n Schottky diodes form an n-input AND gate. As long as one of the signals in A1~An outputs logic 0, the Output outputs logic 0. Only when ...; 灞波儿奔 Analogue and Mixed Signal

Will there be any interference in this way? Please ask an expert: Will there be any interference in this way? Please ask an expert...; yangjianyuen PCB Design

Reply about 1MHz jammer: Hello, 1MHz belongs to the medium wave frequency band. I don't know the field strength and modulation method of the signal source you want to interfere with. I can only provide you with a 10W 1MHz hig...; RF研究 RF/Wirelessly

How to connect the four pins of the oscillator: Please help me with some advice. How to connect the four pins of the oscillator? Does it output the frequency directly or does it require some peripheral circuit? I recently wanted to use an active os...; 小宋 Analog electronics

Help, how to replace the Zener diode with another circuit?: [color=#252525]The question stipulates that the voltage regulator diode is not allowed, so how should this circuit be modified to only use capacitors, resistors, inductors and other components? I am a...; wty1998 Analog electronics

Original goods, new goods in bulk, refurbished goods, disassembled parts, cut board ICs...what do they mean exactly?: In order to cope with the shortage and price increase of chips, in addition to trying every possible way to find domestic alternatives, there are also some people who use different channels to look fo...; eric_wang DIY/Open Source Hardware

Shortcut: A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 AA AB AC AD AE AF AG AH AI AJ AK AL AM AN AO AP AQ AR AS AT AU AV AW AX AY AZ B0 B1 B2 B3 B4 B5 B6 B7 B8 B9 BA BB BC BD BE BF BG BH BI BJ BK BL BM BN BO BP BQ BR BS BT BU BV BW BX BY BZ C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 CA CB CC CD CE CF CG CH CI CJ CK CL CM CN CO CP CQ CR CS CT CU CV CW CX CY CZ D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 DA DB DC DD DE DF DG DH DI DJ DK DL DM DN DO DP DQ DR DS DT DU DV DW DX DZ

Popular Components