EEWORLDEEWORLDEEWORLD

Part Number

Search

Y40621K00000Q0R

Description
res 1K ohm .3W .02% 0805
CategoryPassive components   
File Size2MB,7 Pages
ManufacturerVishay
Websitehttp://www.vishay.com
Environmental Compliance  
Download Datasheet View All

Y40621K00000Q0R Overview

res 1K ohm .3W .02% 0805

FRSH Series (0603, 0805, 1206, 1506, 2010, 2512) (Z1-Foil)
Vishay Foil Resistors
Ultra High Precision Foil Wraparound Surface Mount Chip Resistor
with Extended Pads for High Power/High Temperature Applications
up to +225°C, Load Life Stability of 0.05% ,TCR to ± 1ppm/°C
FEATURES
Temperature coefficient of resistance (TCR):
±1 ppm/°C typical (- 55 °C to + 125 °C, + 25 °C ref.)
±2.5 ppm/°C typical (- 55 °C to + 200 °C, + 25 °C
ref.)
Resistance range: 10 to 125 k(for higher
and lower values, please contact VFR's
application engineering department)
Resistance tolerance: to ± 0.02 %
Working power
(1)
: to 1200mW at + 70 °C;
to 330mW at + 200 °C
Long term stability: to ± 0.05 % at + 225 °C for 2000h,
no power
Load life stability: to ± 0.05 % at + 200 °C for 2000h, at
working power
Vishay Foil resistors are not restricted to standard values;
specific "as required" values can be supplied at no extra
cost or delivery (e.g. 1K2345 vs. 1K)
Thermal stabilization time < 1 s (nominal value achieved
within 10 ppm of steady state value)
Electrostatic discharge (ESD) at least to 25 kV
Non inductive, non capacitive design
Rise time: 1 ns effectively no ringing
Current noise: 0.010 µV (RMS)/Volt of applied voltage
(< - 40 dB)
Voltage coefficient: < 0.1 ppm/V
Non inductive: < 0.08 µH
Non hot spot design
Terminal finishes available:
High temperature solder
Matched sets are available on request
Prototype quantities available in just 5 working days
or sooner. For more information, please contact
foil@vishaypg.com
INTRODUCTION
Vishay Foil Resistors (VFR) introduces a new line of Ultra
Precision Bulk Metal
®
Z1-Foil technology: wraparound
surface mount chip resistors with extended pads for high
temperature up to + 225 °C
(1)
(working power: to 330mW at
+200 °C).
The new extended pad designs also exhibit better heat
dissipation, thus enabling higher power usage (Working
Power: to 1200mW at + 70°C
(1)
). The FRSH has a full
wraparound termination that ensures safe handling during
the manufacturing process, as well as providing stability
during multiple thermal cyclings.
The FRSH is available in any value within the specified
resistance range. VFR's application engineering department
is available to advise and make recommendations. For
non-standard
technical
requirements
and
special
applications, please contact
foil@vishaypg.com.
TABLE 1 - TOLERANCE AND TCR VS.
RESISTANCE VALUE
(1)(2)
(- 55 °C to + 200 °C, + 25 °C Ref.)
RESISTANCE
VALUE
()
250to 125K
100to < 250
50to < 100
25to < 50
10 to < 25
TOLERANCE
(%)
± 0.02
± 0.05
± 0.1
± 0.25
± 0.5
Percent of Rated Power
Note
(1)
Performances obtained with ceramic PCB.
(2)
For tighter performances and non-standard values up to 150 k,
please contact VFR's application engineering department by
sending an e-mail to the address in the footer below.
Document Number: 63211
Revision: 20-Mar-12
PR
EL
IM
IN
AR
Y
TCR Typical
(ppm/°C)
-55°C
+70°C
100
75
50
25
0
-75
FIGURE 1 - POWER DERATING CURVE
±2.5
-50
-25
0
+25
+50
+75 +100 +125 +150 +175 +200 +225 +250
Ambient Temperature (°C)
For any questions, contact:
foil@vishaypg.com
www.vishayfoilresistors.com
1
Linux kernel module index map
Share it. Because it is difficult to quote, I will just put the link: [url=http://www.linuxdriver.co.il/kernel_map]http://www.linuxdriver.co.il/kernel_map[/url] [url=http://cs.jhu.edu/%7Erazvanm/fs-ex...
冰人 Linux and Android
Please advise on the communication principle of LED electronic screen
I am a novice in single-chip microcomputer research, and I have recently been studying LED. I learned based on the schematic diagrams and C language codes on the Internet. But I found that the informa...
kd911 MCU
I would like to ask how to calculate the current of the external gate-source capacitor of IGBT
[i=s]This post was last edited by sunboy25 on 2021-12-27 22:50[/i]I would like to ask the experts, in the IGBT driving circuit as shown in the figure below, how should the maximum instantaneous curren...
sunboy25 Analogue and Mixed Signal
Online interview
Today, a boss came to me on QQ and said he would provide food and accommodation for 2.5k in Shanxi. I don't know if it's true or not. I'm a little skeptical. I'm in Chengdu now. I'm not very clear abo...
终极菜鸟 Talking about work
Determining the working status of multiple transistor coupling
Hello everyone, I am a sophomore in analog electronics. I am preparing for the fourth edition of the book "Fundamentals of Analog Electronics Technology" edited by Hua Chengying . I am confused about ...
模电大二萌新 Analog electronics
A simple study of 51 single-chip Keil C delay program (transferred)
When using a single-chip microcomputer, you often encounter situations where a short delay is required. The required delay time is very short, usually tens to hundreds of microseconds (us). Sometimes ...
rain 51mcu

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2304  2582  1340  354  319  47  52  27  8  7 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号