WBC-T0303AG-05-54R9-FG datasheet, PDF

Datasheet> All Categories > Passive components> The resistor> WBC-T0303AG-05-54R9-FG

WBC-T0303AG-05-54R9-FG: DescriptionArray/Network Resistor, Center Tap, Thin Film, 0.25W, 54.9ohm, 100V, 1% +/-Tol, -100,100ppm/Cel, 0303,; CategoryPassive components The resistor; File Size376KB，3 Pages; ManufacturerTT Electronics plc; Websitehttp://www.ttelectronics.com/; Environmental Compliance

Download Datasheet Parametric View All

WBC-T0303AG-05-54R9-FG Overview

Array/Network Resistor, Center Tap, Thin Film, 0.25W, 54.9ohm, 100V, 1% +/-Tol, -100,100ppm/Cel, 0303,

WBC-T0303AG-05-54R9-FG Parametric

Parameter Name	Attribute value
Is it Rohs certified?	conform to
Objectid	802623017
Reach Compliance Code	compliant
ECCN code	EAR99
structure	Chip
Network Type	Center Tap
Number of terminals	6
Maximum operating temperature	150 °C
Minimum operating temperature	-55 °C
Package length	0.762 mm
Package form	SMT
Package width	0.762 mm
method of packing	Tray
Rated power dissipation(P)	0.25 W
Guideline	MIL-PRF-38534
resistance	54.9 Ω
Resistor type	ARRAY/NETWORK RESISTOR
series	WBC(TAPPED)
size code	0303
technology	THIN FILM
Temperature Coefficient	100 ppm/°C
Tolerance	1%
Operating Voltage	100 V

Preview

Download Datasheet

View All

Wire Bondable

Chip Resistors

WBC Series

•

Discrete or tapped schematics

•

MIL inspection available

•

High resistor density

IRC Advanced Film Division

IRC’s WBC series wire bondable chip resistors are ideally suited for

the most demanding hybrid application. The WBC combines IRC’s

TaNSil

tantalum nitride thin ﬁlm technology with silicon substrate processing to produce an extremely small

footprint device with the proven stability, reliability and moisture performance of IRC’s TaNSil

resistor ﬁlm.

Available in a wide range of tolerances and temperature coefﬁcients to ﬁt a variety of hybrid circuit applica-

tions. Custom resistance values, sizes and schematics are available on request from the factory.

Physical Data

R0202 - Discrete

(0.508mm ±0.025)

0.020˝ ±0.001

Electrical Data

Absolute Tolerance

Absolute TCR

Package Power Rating

(@ 70°C)

Rated Operating Voltage

(not to exceed

√

P x R )

Operating Temperature

Back contact

Noise

Substrate Material

Top contact

Substrate Thickness

Aluminum

Gold

R0202 and

T0303

B0202

Passivation

to ±0.1%

to ±25ppm/°C

250mW

100V

-55°C to +150°C

<-30dB

Oxidized Silicon

(10KÅ SiO

min)

0.010˝ ±0.001

(0.254mm ±0.025)

10KÅ minimum

15KÅ minimum

Silicon

(Gold available)

Gold

3KÅ minimum

Silicon Dioxide or

Silicon Nitride

0.004˝ min bond pad size

0.020˝ ±0.001

(0.508mm ±0.025)

B0202 - Discrete back contact

(0.508mm ±0.025)

0.020˝ ±0.001

Top contact

pad chamfered

0.004˝ min bond pad size

0.020˝ ±0.001

(0.508mm ±0.025)

T0303 - Tapped network ½R + ½R

Bond Pad

Metallization

(0.762mm ±0.025)

0.030˝ ±0.001

Backside

½R

0.030˝ ±0.001

(0.762mm ±0.025)

0.004˝ min bond pad size

General Note

IRC reserves the right to make changes in product speciﬁcation without notice or liability.

All information is subject to IRC’s own data and is considered accurate at time of going to print.

• Corpus Christi Texas 78411 USA

Telephone: 361 992 7900 • Facsimile: 361 992 3377 • Email: afdsales@irctt.com • Website: www.irctt.com

A subsidiary of

TT electronics plc

WBC Series Issue April 2006

Recommended Resources

Pure resistive series negative feedback circuit

Practical circuit diagram of single-ended flyback switching power supply using UC3842

Pulse position modulator circuit diagram

Reversible inching and starting hybrid control circuit diagram

Electronic ventriloquist circuit

Appearance and dimensions of T/R40 ultrasonic sensor

createdialog no wm_command message: When creating a dialog from the same template, using dialogbox, everything works fine. However, when creating a dialog using createdialog, there is only WM_INITDIALOG in the callback, but no WM_COMMAN...; 宝剑出鞘 Embedded System

The problem has been found! STM32 made a 485 communication, but it turned out to be a ghost! Please help me find the ghost!!!: [i=s] This post was last edited by Xiaoyue on 2016-11-23 10:44 [/i] Let me explain the cause of the problem: There is a frequency detection circuit in the board that detects the 50Hz industrial freque...; 小跃同学 stm32/stm8

Help: Can the source code of the msp series chips be universal?: Is it impossible to port the chip codes between different MSP models? If so, what needs to be modified?...; shell_1010 Microcontroller MCU

ADI commonly used chips: [i=s]This post was last edited by paulhyde on 2014-9-15 03:45[/i]1.Analog-to-digital converter AD1380JD 16-bit 20us high-performance analog-to-digital converter (civilian grade) AD1380KD 16-bit 20us h...; paulhyde Electronics Design Contest

How to conduct accurate and cost-effective high-brightness LED testing starting from basic device characteristics: Keithley experts invite you to first learn about " High Brightness LED Test (HBLED) " High brightness light emitting diodes ( HBLED ) combine the advantages of high output, high efficiency and long li...; Jack_ma Test/Measurement

There is Ximen Shopping Mall in front and Shenzhen Huaqiangbei in the back!: Haha, I recommend Zhang Wuji 1987's blog to everyone: [url=https://home.eeworld.com.cn/my/space.php?uid=159276&do=blog&id=30702]https://home.eeworld.com.cn/my/space.php?uid=159276&do=blog&id=30702[/ur...; soso Analog electronics

Shortcut: A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 AA AB AC AD AE AF AG AH AI AJ AK AL AM AN AO AP AQ AR AS AT AU AV AW AX AY AZ B0 B1 B2 B3 B4 B5 B6 B7 B8 B9 BA BB BC BD BE BF BG BH BI BJ BK BL BM BN BO BP BQ BR BS BT BU BV BW BX BY BZ C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 CA CB CC CD CE CF CG CH CI CJ CK CL CM CN CO CP CQ CR CS CT CU CV CW CX CY CZ D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 DA DB DC DD DE DF DG DH DI DJ DK DL DM DN DO DP DQ DR DS DT DU DV DW DX DZ

Popular Components