EEWORLDEEWORLDEEWORLD

Part Number

Search

Y1627184R000B0R

Description
Fixed Resistor, Metal Foil, 0.5W, 184ohm, 187V, 0.1% +/-Tol, -.2,.2ppm/Cel, 2010,
CategoryPassive components    The resistor   
File Size838KB,6 Pages
ManufacturerVishay
Websitehttp://www.vishay.com
Download Datasheet Parametric View All

Y1627184R000B0R Overview

Fixed Resistor, Metal Foil, 0.5W, 184ohm, 187V, 0.1% +/-Tol, -.2,.2ppm/Cel, 2010,

Y1627184R000B0R Parametric

Parameter NameAttribute value
Is it Rohs certified?incompatible
Objectid860447816
Reach Compliance Codenot_compliant
Country Of OriginIsrael
ECCN codeEAR99
YTEOL10
Other featuresNON INDUCTIVE; ULTRA HIGH PRECISION
structureRectangular
Installation featuresSURFACE MOUNT
Number of terminals2
Maximum operating temperature150 °C
Minimum operating temperature-55 °C
Package height0.64 mm
Package length5.03 mm
Package formSMT
Package width2.46 mm
method of packingTR
Rated power dissipation(P)0.5 W
Rated temperature70 °C
resistance184 Ω
Resistor typeFIXED RESISTOR
size code2010
surface mountYES
technologyMETAL FOIL
Temperature Coefficient0.2 ppm/°C
Terminal surfaceTIN LEAD SILVER OVER NICKEL
Terminal shapeWRAPAROUND
Tolerance0.1%
Operating Voltage187 V
VSMP Series(0603,0805,1206,1506,2010,2010,(ZFoil)
VSMP Series (0603, 0805, 1206, 1506, 2512) 2512)
(Z Foil)
Ultra High Precision Foil Wraparound Surface Mount Chip Resistor
with TCR of ±0.05 ppm/°C and Power Coefficient of 5 ppm at
Rated Power and Load Life Stability of ±0.005% (50 ppm)
FEATURES
• Temperature coefficient of resistance (TCR):
0.2 ppm/°C typical (–55°C to +125°C, +25°C ref.)
• Resistance tolerance: to ±0.01%
• Power coefficient “∆R due to self heating”:
5 ppm at rated power
• Power rating: to 750 mW at +70°C (see table 3)
• Load life stability: to ±0.005% at 70°C, 2000 h
at rated power
• Resistance range: 5 Ω to 125 kΩ (for lower or higher
values, please contact us)
• Bulk Metal Foil resistors are not restricted to standard
values, we can supply specific “as required” values at
no extra cost or delivery (e.g. 1K2345 vs. 1K)
• Thermal stabilization time <1 s (nominal value achieved
within 10 ppm of steady state value)
• Electrostatic discharge (ESD) at least to 25 kV
• Short time overload: ≤0.005%
• Non inductive, non capacitive design
• Rise time: 1 ns effectively no ringing
• Current noise: 0.010 μV
RMS
/V of applied voltage
(<–40 dB)
• Voltage coefficient <0.1 ppm/V
(resistance values above 10 kΩ)
• Non inductive: <0.08 μH
• Non hot spot design
• Terminal finishes available: lead (Pb)-free, tin/lead alloy
• Matched sets are available on request
• Screening in accordance with EEE-INST-002 and
MIL-PRF-55342 available (see datasheet resistor
models 303133 to 303138)
• Quick prototype quantities available, please contact
foil@vpgsensors.com
Top View
(for date code print specification please refer to table 2)
INTRODUCTION
VSMP Series is the industry’s first device to provide high
rated power and excellent load life stability along with
extremely low TCR – all in one resistor.
One of the most important parameters influencing stability
is the Temperature Coefficient of Resistance (TCR).
Although the TCR of Bulk Metal
®
Foil is considered
extremely low, this characteristic has been further
refined over the years. The VSMP Series utilizes ultra
high precision Z Foil. The Z Foil technology provides a
significant reduction of the resistive element’s sensitivity
to ambient temperature variations (TCR) and to self
heating when power is applied (Power Coefficient of
Resistance, or PCR). Along with the inherently low PCR
and TCR, Z Foil technology also provides remarkably
improved load life stability, low noise and tight tolerances.
Vishay Foil Resistors’ (VFR) application engineering
department is available to advise and make
recommendations. For non-standard technical
requirements and special applications, please contact
us using the e-mail address in the footer below.
Table 1—Tolerance and TCR vs. Resistance
Value
(1)
(–55°C to +125°C, +25°C Ref.)
Resistance value
250 Ω to 125 kΩ
100 Ω to <250 Ω
50 Ω to <100 Ω
25 Ω to <50 Ω
10 Ω to <25 Ω
5 Ω to <10 Ω
(1)
Figure 1—Power Derating Curve
Percent of Rated Power
100
75
50
25
0
- 75
Tolerance
±0.01%
±0.02%
±0.05%
±0.1%
±0.25%
±0.5%
Typical TCR and
max. Spread
±0.2 ±1.8 ppm/°C
±0.2 ±1.8 ppm/°C
±0.2 ±2.8 ppm/°C
±0.2 ±3.8 ppm/°C
±0.2 ±3.8 ppm/°C
±0.2 ±7.8 ppm/°C
- 55 °C
+ 70 °C
For tighter performances and non-standard values lower than
5 Ω and above 125 kΩ, please contact application engineering
using the e-mail addresses in the footer below
- 50
- 25
0
+ 25 + 50 + 75 + 100 + 125 + 150 + 175
Ambient Temperature (°C)
* This datasheet provides information about parts that are RoHS-compliant and/or parts that are non-RoHS-compliant.
For example, parts with lead (Pb) terminations are not RoHS compliant. Please see the information/tables in this datasheet for details.
4128-EN
Rev 04-Mar-2020
For any questions, contact
foil@vpgsensors.com
www.vishayfoilresistors.com
1
NI China Branch has implemented a direct sales model since 2006
----Local users can enjoy more favorable product prices, faster delivery services and the same high-quality technical support.National Instruments China Co., Ltd. (NI) announced that it will officiall...
rain MCU
Microchip Live at 10:30 AM today | Securely configure the MPU in your factory
Secure provisioning is a process that allows you to securely instantiate a microprocessor ( MPU) root of trust. In this webinar, Microchip will explain why secure provisioning is important for MPU-bas...
EEWORLD社区 Industrial Control Electronics
EEWORLD University ---- Introduction to TPS56x201/8 DC Buck
Introduction to TPS56x201/8 DC Buck : https://training.eeworld.com.cn/course/4172...
hi5 Power technology
How to identify the quality of LED full-color display
The quality of a full-color display can be judged mainly from the following aspects:    1. Flatness    The surface flatness of the display screen should be within ±1mm to ensure that the displayed ima...
探路者 LED Zone
TLP521 optocoupler isolation resistor size selection problem
In the figure, the CON point should be pulled up to a high level, but the actual test shows only 0.8V. Why is this? How can I pull up the CON point to close the optocoupler switch? [[i] This post was ...
linjingui Test/Measurement
Ask a question about the design of Altera DE-2 (high score help)
Now I want to use an Altera de-2 chip to simulate the performance of a system design. One solution is to design a router by myself, and then a 3*3 mesh structure. In addition, each router is connected...
zfnlj Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2488  1668  1135  1368  314  51  34  23  28  7 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号