Y08501R00000F0W datasheet, PDF

Datasheet> All Categories > Passive components> Y08501R00000F0W

Preview

Y08501R00000F0W: Descriptionres 1 ohm 1/2W 1% 2516 wide; CategoryPassive components; File Size983KB，5 Pages; ManufacturerVishay; Websitehttp://www.vishay.com

Download Datasheet View All

Y08501R00000F0W Overview

res 1 ohm 1/2W 1% 2516 wide

Preview

Download Datasheet

View All

303119Z, 303119

Vishay Foil Resistors

Models # 303119Z and 303119 (Current Sensing Fixed Foil Resistor Chips

VCS1625Z/VCS1625 Configuration) Screen/Test Flow in Compliance with

EEE-INST-002, (Tables 2A and 3A, Film/Foil, Level 1) and MIL-PRF-55342

FEATURES



Temperature coefficient of resistance (TCR):



± 0.05 ppm/°C typical (0 °C to + 60 °C)

± 0.2 ppm/°C typical (- 55 °C to + 125 °C, + 25 °C ref.)

(see table 1)



Resistance range: 0.01



to 10



INTRODUCTION

The Z-foil technology provides a significant reduction of

the resistive component’s sensitivity to ambient temperature

variations (TCR) and applied power changes (PCR).

Designers can now guarantee a high degree of stability

and accuracy in fixed-resistor applications using solutions

based on Vishay‘s revolutionary Z-foil technology.

0.05 ppm/°C absolute TCR removes errors due to

temperature gradients.

Models 303119Z and 303119 are surface mount chip

resistors designed with 4 pads for Kelvin connection.

Utilizing Vishay’s Bulk Metal

Z-foil as the resistance

element, 303119Z provides performance capabilities far

greater than other resistor technologies can supply in a

product of comparable size.

These small devices dissipate heat almost entirely through

the pads so surface mount users are encouraged to be

generous with the board’s pads and traces. Gold

terminations are available as well.

Our application engineering department is available to

advise and to make recommendations.



Vishay Foil resistors are not restricted to standard values,

specific “as required” values can be supplied at no extra

cost or delivery (e.g. 1.234



vs. 1

)



Tolerance: to ± 0.5 %



Power coefficient “R due to self heating”: 5 ppm at rated

power



Load life stability: 0.05 % at 70 °C, 2000 h at rated power



Electrostatic discharge (ESD) up to 25 000 V



Short time overload < 0.02 %



Power rating: 0.5 W at + 70 °C (figure 1)



Non inductive, non capacitive design



Rise time: 1 ns effectively no ringing



Current rating: 5 A maximum



Current noise: < - 40 dB



Voltage coefficient: < 0.1 ppm/V



Non inductive: < 0.08 µH



Non hot spot design



For prototypes units, append a “U” to the model number

(example: 303119ZU). These units have all of the table 2A

(page 3) 100 % tests performed, with no destructive

qualification testing required (table 3A, page 3). For more

information, please contact

foil@vishaypg.com



For oriented performances please contact us

FIGURE 1 - POWER DERATING CURVE

Percent of Rated Power

- 55 °C

100

- 75

+ 70 °C

TERMINATIONS



Two options are available:

- tin/lead plated

- 50

- 25

+ 25

+ 50

+ 75 + 100 + 125 + 150 + 175

Ambient Temperature (°C)

- gold plated

TABLE 1 - SPECIFICATIONS

MODEL

NUMBER

303119Z

RESISTANCE

RANGE

> 2.0



to 10



> 0.5



to 2.0



0.3



to 0.5



> 2.0



to 10



> 0.5



to 2.0



> 0.1



to 0.5



> 0.05



to 0.1



> 0.03



to 0.05



> 0.01



to 0.03



TIGHTEST RESISTANCE

TOLERANCE

± 0.5 %

± 1.0 %

± 2.0 %

± 0.5 %

± 1.0 %

± 2.0 %

TYPICAL TCR

MAXIMUM TCR

(- 55 °C to + 125 °C, + 25 °C ref.)

± 0.2 ppm/°C

± 3 ppm/°C

± 5 ppm/°C

± 10 ppm/°C

± 15 ppm/°C

± 20 ppm/°C

± 30 ppm/°C

± 50 ppm/°C

0.5 W on FR4 PCB

POWER RATING

at + 70 °C

(1)

MAXIMUM

CURRENT

(1)

303119

± 2.0 ppm/°C

Note

(1)

Whichever is lower

Document Number: 63167

Revision: 12-Jan-12

For any questions, contact:

foil@vishaypg.com

www.vishayfoilresistors.com

Legal Disclaimer Notice

Vishay Precision Group, Inc.

Disclaimer

ALL PRODUCTS, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE.

Vishay Precision Group, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf

(collectively, “VPG”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained herein or in

any other disclosure relating to any product.

The product specifications do not expand or otherwise modify VPG’s terms and conditions of purchase, including but

not limited to, the warranty expressed therein.

VPG makes no warranty, representation or guarantee other than as set forth in the terms and conditions of purchase.

To the maximum extent permitted by applicable law, VPG disclaims (i) any and all liability arising out of the

application or use of any product, (ii) any and all liability, including without limitation special, consequential or

incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose,

non-infringement and merchantability.

Information provided in datasheets and/or specifications may vary from actual results in different applications and

performance may vary over time. Statements regarding the suitability of products for certain types of applications

are based on VPG’s knowledge of typical requirements that are often placed on VPG products. It is the customer’s

responsibility to validate that a particular product with the properties described in the product specification is suitable for

use in a particular application. You should ensure you have the current version of the relevant information by contacting

VPG prior to performing installation or use of the product, such as on our website at vpgsensors.com.

No license, express, implied, or otherwise, to any intellectual property rights is granted by this document, or by any

conduct of VPG.

The products shown herein are not designed for use in life-saving or life-sustaining applications unless otherwise

expressly indicated. Customers using or selling VPG products not expressly indicated for use in such applications do

so entirely at their own risk and agree to fully indemnify VPG for any damages arising or resulting from such use or sale.

Please contact authorized VPG personnel to obtain written terms and conditions regarding products designed for such

applications.

Product names and markings noted herein may be trademarks of their respective owners.

Document No.: 63999

Revision: 15-Jul-2014

www.vpgsensors.com

Recommended Resources

Thermostatic soldering iron circuit

bistable circuit

Protection circuit diagram using field effect transistors

Current expansion circuit with external transistor and external NPN switch circuit diagram

Simple current sink circuit diagram

600MHz broadband amplifier circuit

Talk about TI M3 day technical seminar: I was lucky enough to attend the 2011 TI M3 Day Technical Seminar (Guangzhou) today. Thank you TI for providing me with this opportunity, giving me a chance to get close to a big company and let me se...; longxtianya Microcontroller MCU

Summer, are you lazy?: When the weather is hot, you can grill directly on the stones. But sitting in front of the computer seems too lazy, right?...; zqjqq88 Talking

Wince burning problem: I rebooted after burning wince's nboot. I got this error: wince nand boot v1.00 mar 22 2007 00:02:34 picture boot wince nand boot v1.00 mar 22 2007 12:25:45 dwEntry is 0x00000001 ECC ERROR: 0x00000020...; zhang_shuai2005 Embedded System

STM8ADC and GPIO operation questions: STM8S105K6PB0PB1 > GPIO outputPB2The problem I am facing now is that after AIN2 ADC is initialized, AIN2 can collect data normally, but the PB0 status cannot be read. Have I encountered another BUG......; caobenda stm32/stm8

I use ATmega32's JTAG, why does the connection always fail? ? Please help: I use ATmega32 JTAG. First of all, the circuit is correct. I have verified it many times. The chip is also new. In addition, Jtag ports 1, 3, 5, and 9 are all connected to pull-up resistors. When prog...; zixialong Microchip MCU

[TI's First Low Power Design Competition] Micro LCR Tester - Hardware Part 4: This article will introduce the power supply part of LCRThe figure above is the principle block diagram of the power supply part. The right side is a typical single-button switch circuit. The switch i...; snoweaglemcu Microcontroller MCU

Shortcut: E0 E1 E2 E3 E4 E5 E6 E7 E8 E9 EA EB EC ED EE EF EG EH EI EJ EK EL EM EN EO EP EQ ER ES ET EU EV EW EX EY EZ F0 F1 F2 F3 F4 F5 F6 F7 F8 F9 FA FB FC FD FE FF FG FH FI FJ FK FL FM FN FO FP FQ FR FS FT FU FV FW FX FY FZ G0 G1 G2 G3 G4 G5 G6 G7 G8 G9 GA GB GC GD GE GF GG GH GI GJ GK GL GM GN GO GP GQ GR GS GT GU GV GW GX GZ H0 H1 H2 H3 H4 H5 H6 H7 H8 HA HB HC HD HE HF HG HH HI HJ HK HL HM HN HO HP HQ HR HS HT HU HV HW HX HY HZ I1 I2 I3 I4 I5 I6 I7 IA IB IC ID IE IF IG IH II IK IL IM IN IO IP IQ IR IS IT IU IV IW IX J0 J1 J2 J6 J7 JA JB JC JD JE JF JG JH JJ JK JL JM JN JP JQ JR JS JT JV JW JX JZ K0 K1 K2 K3 K4 K5 K6 K7 K8 K9 KA KB KC KD KE KF KG KH KI KJ KK KL KM KN KO KP KQ KR KS KT KU KV KW KX KY KZ

Popular Components