EEWORLDEEWORLDEEWORLD

Part Number

Search

PHP00603E2710BBT1

Description
res 271 ohm 3/8W .1% 0603
CategoryPassive components   
File Size146KB,5 Pages
ManufacturerVishay
Websitehttp://www.vishay.com
Download Datasheet View All

PHP00603E2710BBT1 Overview

res 271 ohm 3/8W .1% 0603

PHP
www.vishay.com
Vishay Dale Thin Film
High Power Thin Film Wraparound Chip Resistor
FEATURES
PHP series chip resistors are designed with enlarged
backside terminations to reduce the thermal resistance
between the topside resistor layer and the solder joint on the
end users circuit board.
Actual power handling capability is limited by the end user
mounting process. As with any high power chip resistor the
ability to remove the generated heat is critical to the overall
performance of the device.
High purity ceramic substrate
Power rating to 2.5 W
Resistance range 10
to 30.1 k
Resistor tolerance to ± 0.1 %
TCR to ± 25 ppm/°C
Flame resistant UL 94 V-0
Power supplies
Power switching
Braking system
Test and measurement equipment
Motor deflection circuits
APPLICATIONS
TYPICAL PERFORMANCE
ABSOLUTE
TCR
TOL.
25
0.1
STANDARD ELECTRICAL SPECIFICATIONS
TEST
Material
Resistance Range
TCR: Absolute
Tolerance: Absolute
Power Rating: Resistor
Stability: Absolute
Stability: Ratio
Voltage Coefficient
Working Voltage
Operating Temperature Range
Storage Temperature Range
Noise
Shelf Life Stability: Absolute
SPECIFICATIONS
Nichrome
10
to 30.1 k
25 ppm/°C, 50 ppm/°C (standard)
and, 100 ppm/°C
0.1 %, 0.5 %, 1.0 % and, 5.0 %
0.375 W - 2.5 W
(1)
R
0.1 %
Not applicable
< 0.1 ppm/V
75 V to 200 V
-55 °C to +155 °C
-55 °C to +155 °C
< -30 dB
± 0.01 %
CONDITIONS
-
-
-55 °C to +125 °C
+25 °C
Maximum at +70 °C
2000 h at +70 °C
-
-
-
-
-
-
1 year at +25 °C
COMPONENT RATINGS
CASE SIZE
POWER RATING (mW)
0603
375
(1)
0805
625
(1)
1206
1000
(1)
2512
2500
(1)
Note
(1)
Dependent on component mounting by user.
WORKING VOLTAGE (V)
75
100
200
200
RESISTANCE RANGE ()
10 to 30.1K
10 to 30.1K
10 to 30.1K
10 to 30.1K
ENVIRONMENTAL TESTS
(Vishay Performance vs. MIL-PRF-55342 Requirements)
ENVIRONMENTAL TEST
Resistance Temperature Characteristic
Maximum Ambient Temperature at Rated Wattage
Maximum Ambient Temperature at Power Derating
Thermal Shock
Low Temperature Operation
Short Time Overload
High Temperature Exposure
Resistance to Soldering Heat
Moisture Resistance
Life at +70 °C for 2000 h
Revision: 27-Jun-16
LIMITS MIL-PRF-55342
CHARACTERISTIC “E”
± 25 ppm/°C
+70 °C
+150 °C
± 0.1 %
± 0.1 %
± 0.1 %
± 0.1 %
± 0.2 %
± 0.2 %
± 0.5 %
TYPICAL VISHAY PERFORMANCE
± 15 ppm/°C
+70 °C
+150 °C
± 0.04 %
± 0.001 %
± 0.003 %
± 0.030 %
± 0.007 %
± 0.002 %
± 0.100 %
Document Number: 60076
1
For technical questions, contact:
thinfilm@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT
www.vishay.com/doc?91000
The amplification factor of the op amp in the TI schematic
When looking at the schematic diagram of TI's official BLDC development board, I have some questions about the op amp method multiples. How is it calculated? I calculated it to be 25. Can someone expl...
1243026497 Microcontroller MCU
Help
Looking for installation software for MAX+plusII10.2 and QuartusII.v50...
xiaoxiaoha FPGA/CPLD
Application of Double Balanced Mixer in Mixing Circuit of TV Transmitter
[i=s]This post was last edited by jameswangsynnex on 2015-3-3 20:00[/i]With the development of China's radio and television industry, TV transmitter equipment has been updated for many times. TV trans...
JasonYoo Mobile and portable
Learning simulation + reducing cable crosstalk
[i=s]This post was last edited by dontium on 2015-1-23 11:39[/i] [b][size=3]How to minimize crosstalk in cable design[/size][/b][size=3]deyisupport./blog/b/analogwire/archive/2014/01/22/51614.aspx[/si...
machinnneee Analogue and Mixed Signal
Does anyone know about the FDS9435 chip?
I want to use this chip to control the power supply recently, but the data sheet doesn't seem to explain it in detail. I want to ask if this chip can be directly controlled by FPGA or does it need to ...
明天你好123 Power technology
Button control water flow light: press key1, LED1-8 will flow in sequence, press key2, LED1/3/5/7 (4 intervals)...
It is stipulated that delay functions cannot be used, only timers can be used Please help me find out what is wrong. It didn't work in the end.#include STC12C5A60S2.Hunsigned int Count_disturb = 0; //...
姜先生、初一 51mcu

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2539  1064  1457  1567  2712  52  22  30  32  55 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号