TK111xxCS
LDO REGULATOR WITH ON/OFF CONTROL
TK111xxCS
1. DESCRIPTION
TK111xxC is an integrated circuit of the silicon
monolithic bipolar structure, and the regulator of the
low saturation output type with very little quiescent
current (63mA).
The PNP power transistor is Built-in to. The I/O voltage
difference when the current of Typ.200mA is supplied to
the system is 0.2V. The voltage source can be effectively
used.
Therefore, It is the best for the battery use set.
The on/off function is Built-in to IC. The current at
standing-by mode becomes slight (pA level).
1.5 to 10.0V is arranged to the output voltage in 0.1V step.
The output voltage is trimmed in high accuracy. The best
voltage for the set used will be able to be selected.
The over current sensor circuit and the reverse-bias over
current obstruction circuit are Built-in to.
It is a design not broken because an ESD is also high. It is
possible to use (*O) at ease.
When mounting on PCB, the loss becomes about 500mW
though the package is very small.
TK111xxC uses the circuit with very high stability in DC
and AC.
The capacitor on the output side is steady in 0.1mF
(1.8V£Vout). The kind of this capacitor is not asked. It is
possible to use every type capacitor.
However, a good characteristic is shown the more overall
larger this capacitor is.
The ripple rejection is 84dB at 400Hz and 80dB at 1kHz.
3. APPLICATIONS
Any Electronic Equipment
Battery Powered Systems
Mobile Communication
4. PIN CONFIGURATION
Top View
Vcont
GND
Np
1
2
3
5
Vin
4
Vout
5. BLOCK DIAGRAM
Vin
Vout
Control
Circuit
Over Heat &
Over Current
Protection
2. FEATURES
Very good stability C
L
=0.1mF is steady enough. Any
type can be used.(1.8V£V
OUT
)
Very low dropout Voltage. V
DROP
=120mV at 100mA
High Precision output voltage (±1.5% or
±50mV)
Good ripple rejection ratio(80dB at 1kHz)
Wide operating voltage range (1.8V to 14V)
Built-in Short circuit protection
Peak output current is 320mA.(0.3V down point)
Built-in thermal shutdown
Very low quiescent current (I
QUT
=63mA at I
OUT
=0mA)
Available very low noise application
Built-in on/off control (0.1mA Max Standby current)
High On
Very small surface mount package
Built-in reverse bias over current protection
320kW
Bandgap
Reference
500kW
Vcont
GND
Np
GC3-H008J
Page 2
TK111xxCS
6. ORDERING INFORMATION
T K 1 1 1
Voltage Code
(Refer to the following table)
Version
C
Package Code
S : SOT23-5
C S
L -
Environment Code
-G : Lead Free
-GH : Lead Free and Halogen Free
Tape / Reel Code
L : Left Type
Rank Code
C : C Rank
I : I Rank
TK11115CS
TK11116CS
TK11117CS
TK11118CS
TK11119CS
TK11120CS
TK11121CS
TK11122CS
TK11123CS
TK11124CS
TK11125CS
TK11126CS
TK11127CS
TK11128CS
TK11129CS
TK11130CS
TK11131CS
TK11132CS
TK11133CS
TK11134CS
TK11135CS
TK11136CS
TK11137CS
TK11138CS
TK11139CS
TK11140CS
TK11141CS
TK11142CS
TK11143CS
TK11144CS
TK11145CS
TK11146CS
TK11147CS
TK11148CS
TK11149CS
TK11150CS
TK11160CS
TK11185CS
*Please contact your authorized ASAHI KASEI TOKO POWER DEVICES representatives for voltage
availability.
If you need the voltage except the above table, please contact ASAHI KASEI TOKO POWER DEVICES.
7. ABSOLUTE MAXIMUM RATINGS (BOTH C AND I RANK IN COMMON)
T
A
=25
°
C
Parameter
Absolute Maximum Ratings
Supply Voltage
Reverse Bias
NP pin Voltage
Control pin Voltage
Storage Temperature Range
Power Dissipation
Operating Condition
Operating Temperature Range
Operating Voltage Range
Symbol
Vcc
MAX
Vrev
MAX
Vnp
MAX
Vcont
MAX
T
stg
P
D
T
OP
V
OP
Rating
-0.4 ~ 16
-0.4 ~ 6
-0.4 ~ 12
-0.4 ~ 5
-0.4 ~ 16
-55 ~ 150
500 when mounted on PCB
-40 ~ 85
Units
V
V
V
V
V
°C
mW
°
C
Conditions
Vout
£
2.0V
2.1V
£
Vout
Internal Limited T
J
=150°C
*
2.1 ~ 14
V
T
OP
= -40 ~ 80
°
C
1.8 ~ 14
V
T
OP
= -30 ~ 80
°
C
Short Circuit Current
Ishort
360
mA
*
P
D
must be decreased at rate of 4.0mW/°C for operation above 25°C.
The maximum ratings are the absolute limitation values with the possibility of the IC breakage.
When the operation exceeds this standard quality cannot be guaranteed.
GC3-H008J
Page 3
TK111xxCS
8. ELECTRICAL CHARACTERISTICS
8-1. Electrical Characteristics of the C rank
The parameters with min. or max. values will be guaranteed at Ta=Tj=25°C with test when manufacturing or
SQC(Statistical Quality Control) methods. The operation between -40 ~ 85
°
C is guaranteed when design.
Vin=Vout
TYP
+1V,Vcont=1.8V,Ta=Tj=25°C
Parameter
Output Voltage
Line Regulation
Load Regulation
Dropout Voltage
*1
Symbol
Vout
LinReg
LoaReg
Vdrop
Value
MIN
TYP
MAX
Refer to TABLE 1 ~ 3
0.0
5.0
Refer to TABLE 1 ~ 3
Refer to TABLE 1 ~ 3
80
140
120
210
230
350
200
350
240
320
63
0.0
1.0
5.0
1.8
0.35
*1:
For Vout
£
2.0V , no regulations.
*2:
The maximum output current is limited by power dissipation.
100
0.1
1.8
15.0
Units
V
mV
mV
mV
mV
mV
mV
mV
mA
mA
mA
mA
mA
V
V
Conditions
Iout = 5mA
DVin
= 5V
Iout = 5mA ~ 100mA
Iout = 5mA ~ 200mA
Iout = 50mA
Iout = 100mA
Iout = 180mA
(2.1V
£
Vout
£
2.3V)
Iout = 200mA
(2.4V
£
Vout)
Vout=Vout
TYP
´0.9
Iout = 0mA
Vcont = 0V
Iout = 50mA
Vcont = 1.8V
Vout ON state
Vout OFF state
Maximum Output Current
*2
Supply Current
Standby Current
Quiescent Current
Control Terminal
Control Current
Control Voltage
Iout
MAX
Icc
Istandby
Iq
Icont
Vcont
GC3-H008J
Page 4
Embedded System
京公网安备 11010802033920号
EEWORLD
