EEWORLDEEWORLDEEWORLD

Part Number

Search

PIC-37242LO

Description
OPTIC RECEIVER MODULES
CategoryLED optoelectronic/LED    photoelectric   
File Size62KB,2 Pages
ManufacturerKODENSHI
Websitehttp://www.kodenshi.co.jp
Download Datasheet Parametric Compare View All

PIC-37242LO Overview

OPTIC RECEIVER MODULES

PIC-37242LO Parametric

Parameter NameAttribute value
Reach Compliance Codeunknow
Installation featuresTHROUGH HOLE MOUNT
Maximum slew rate0.003 mA
Nominal supply voltage5 V
surface mountNO
Base Number Matches1
PIC-3704 LO / 3724 LO

PIC-37242LO Related Products

PIC-37242LO PIC-3704 PIC-37244LO PIC-37245LO PIC-37243LO PIC-37241LO PIC-37044LO
Description OPTIC RECEIVER MODULES OPTIC RECEIVER MODULES OPTIC RECEIVER MODULES OPTIC RECEIVER MODULES OPTIC RECEIVER MODULES OPTIC RECEIVER MODULES OPTIC RECEIVER MODULES
Reach Compliance Code unknow - unknow unknow unknow unknow unknow
Installation features THROUGH HOLE MOUNT - THROUGH HOLE MOUNT THROUGH HOLE MOUNT THROUGH HOLE MOUNT THROUGH HOLE MOUNT THROUGH HOLE MOUNT
Maximum slew rate 0.003 mA - 0.003 mA 0.003 mA 0.003 mA 0.003 mA 0.003 mA
Nominal supply voltage 5 V - 5 V 5 V 5 V 5 V 5 V
surface mount NO - NO NO NO NO NO
Base Number Matches 1 - 1 1 1 1 1
A question about interruption
I understand that interrupts stop the CPU and execute my interrupt service routine. The interrupt controller controls interrupt enable and priority. According to the ARM documentation, it specifies ea...
tulao Embedded System
Question: How large can the actual ZigBee network range be?
If there is only one gateway and the nodes are densely packed, how large an area can be effectively networked in practice (for temperature sensors)? Also, to be sure, a gateway refers to a node that c...
miaoyannan RF/Wirelessly
About the distance of infrared obstacle avoidance circuit
This is a circuit I found online. The test distance is less than 10CM. How can I increase the distance? I added an NPN transistor to the DO, but it didn't work. I then replaced the receiving tube with...
sky999 PCB Design
FPGA Minimum System Design
When I was working on the minimum FPGA system, when the crystal oscillator output pin was not connected to the FPGA's GCLK, the output amplitude was 2.78V at the maximum and 1.88V at the minimum. But ...
ottomia1 FPGA/CPLD
The stepper motor jitters intermittently after returning to zero - help
I am now using PLC + position module + stepper motor for control and found the following problems: (FX2N-80MR PLC, FX2N-20GM position module, Shenzhen Reise stepper motor;) 1. The stepper motor will j...
eeleader-mcu Industrial Control Electronics
I want to make an LCD setting interface. How to set the number bit by bit? I feel that the method is not very good. I would like to ask if there is a good method
Want to make an LCD setting interface, and set the numbers bit by bit? I use a 12864 LCD without a font library. I want to set the value, for example, 123. First set the hundreds digit, select it, pre...
z755924843 MCU

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2557  938  2512  838  1611  52  19  51  17  33 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号