EEWORLDEEWORLDEEWORLD

Part Number

Search

EZA14HRJN

Description
Card Edge Connector, 14 Contact(s), 1/2 LOADED Row(s), Straight, 0.125 inch Pitch, Solder Terminal, Blue Insulator, Receptacle
CategoryThe connector    The connector   
File Size433KB,3 Pages
ManufacturerSullins Connector Solutions
Download Datasheet Parametric View All

EZA14HRJN Overview

Card Edge Connector, 14 Contact(s), 1/2 LOADED Row(s), Straight, 0.125 inch Pitch, Solder Terminal, Blue Insulator, Receptacle

EZA14HRJN Parametric

Parameter NameAttribute value
Is it lead-free?Contains lead
Is it Rohs certified?incompatible
Objectid1225719560
Reach Compliance Codecompliant
ECCN codeEAR99
Other featuresNONE
body width0.33 inch
subject depth0.406 inch
body length2.575 inch
Body/casing typeRECEPTACLE
Connector typeCARD EDGE CONNECTOR
Contact to complete cooperationNOT SPECIFIED
Contact completed and terminatedTin/Lead (Sn/Pb) - with Nickel (Ni) barrier
Contact materialNOT SPECIFIED
contact modeRECTANGULAR
Contact resistance10 mΩ
Contact styleBELLOWED TYPE
Dielectric withstand voltage800VDC V
maximum insertion force4.448 N
Insulation resistance5000000000 Ω
Insulator colorBLUE
insulator materialPOLYESTER
JESD-609 codee0
Plug contact pitch0.125 inch
Match contact row spacing0.25 inch
Installation methodSTRAIGHT
Installation typeBOARD
Number of connectorsONE
PCB row number1,(1/2 LD)
Number of rows loaded1/2 LOADED
Maximum operating temperature125 °C
Minimum operating temperature-65 °C
PCB contact patternRECTANGULAR
Plating thickness10u inch
Rated current (signal)3 A
GuidelineUL, CSA
reliabilityCOMMERCIAL
Terminal length0.165 inch
Terminal pitch3.175 mm
Termination typeSOLDER
Total number of contacts14
Evacuation force-minimum value.278 N
The video signal carrying capacity close to 1MHz is not enough. What op amp can I use to design a voltage follower?
As the title says, the video signal current output by the linear array CMOS is too small, and the input resistance of the AD module used is only 50ohm. I want to use an op amp to design a voltage foll...
XuYong虚庸 Analog electronics
How does STM32 make AD continuously sample and then delay 500MS before DA continuously outputs
This is my current graduation project: using the AD and DA built into the STM32F103ZET6 chip, the waveform is first continuously collected by the AD and stored in the external SRAM. After 500MS, the C...
wjg2954 stm32/stm8
Research on voice acquisition system and external communication interface based on DSP.pdf
Research on voice acquisition system and external communication interface based on DSP.pdf...
yunhuihe DSP and ARM Processors
Why are the upper and lower rows of pins not parallel when laying out AD devices?
When drawing a minimum system board for STM32, why do the four 2.54*10 pin headers on the top and bottom seem to be bent, wider on the left and narrower on the right?...
littleshrimp Talking
Why does it say here that RBPU needs to be defined?
//----------------------------------------------------------------- // Name: RB port level change interrupt controls the switch of two-digit digital tubes, addition and subtraction display//----------...
嘻嘻嘻嘻啊啊 Microchip MCU
[LPC54100] Wanli board super simple reverse
[i=s]This post was last edited by freebsder on 2015-3-22 14:07[/i] First of all, I want to complain! The schematic is lousy. I have been asking them for it since the board was sent on Monday. It has b...
freebsder MCU

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1789  286  188  2846  2482  37  6  4  58  50 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号