EEWORLDEEWORLDEEWORLD

Part Number

Search

B0202GA-00-5301-D

Description
Fixed Resistor, Thin Film, 0.25W, 5300ohm, 100V, 0.5% +/-Tol, 300ppm/Cel, Surface Mount, 0202, CHIP
CategoryPassive components    The resistor   
File Size381KB,3 Pages
ManufacturerTT Electronics plc
Websitehttp://www.ttelectronics.com/
Download Datasheet Parametric View All

B0202GA-00-5301-D Overview

Fixed Resistor, Thin Film, 0.25W, 5300ohm, 100V, 0.5% +/-Tol, 300ppm/Cel, Surface Mount, 0202, CHIP

B0202GA-00-5301-D Parametric

Parameter NameAttribute value
Objectid1579381435
package instruction, 0202
Reach Compliance Codecompliant
ECCN codeEAR99
Installation featuresSURFACE MOUNT
Number of terminals2
Maximum operating temperature150 °C
Minimum operating temperature-55 °C
Package shapeRECTANGULAR PACKAGE
method of packingTRAY
Rated power dissipation(P)0.25 W
Rated temperature70 °C
resistance5300 Ω
Resistor typeFIXED RESISTOR
size code0202
surface mountYES
technologyTHIN FILM
Temperature Coefficient300 ppm/°C
Terminal shapeONE SURFACE
Tolerance0.5%
Operating Voltage100 V
Wire Bondable
Chip Resistors
WBC Series
Discrete or tapped schematics
MIL inspection available
High resistor density
IRC’s WBC series wire bondable chip resistors are ideally suited for
the most demanding hybrid application. The WBC combines IRC’s
TaNSil
®
tantalum nitride thin film technology with silicon substrate processing to produce an extremely small
footprint device with the proven stability, reliability and moisture performance of IRC’s TaNSil
®
resistor film.
Available in a wide range of tolerances and temperature coefficients to fit a variety of hybrid circuit applica-
tions. Custom resistance values, sizes and schematics are available on request from the factory.
Physical Data
R0202 - Discrete
(0.508mm ±0.025)
0.020˝ ±0.001
Electrical Data
Absolute Tolerance
Absolute TCR
Package Power Rating
(@ 70°C)
Rated Operating Voltage
(not to exceed P x R )
Operating Temperature
Back contact
Noise
R
Top contact
pad chamfered
0.004˝ min bond pad size
to ±0.1%
to ±25ppm/°C
250mW
100V
-55°C to +150°C
<-30dB
Oxidized Silicon
(10KÅ SiO
2
min)
0.010˝ ±0.001
(0.254mm ±0.025)
10KÅ minimum
15KÅ minimum
Silicon
(Al / Au optional)
3KÅ Au minimum
10KÅ Al minimum
Silicon Dioxide or
Silicon Nitride
R
0.004˝ min bond pad size
0.020˝ ±0.001
(0.508mm ±0.025)
B0202 - Discrete back contact
(0.508mm ±0.025)
0.020˝ ±0.001
Substrate Material
Top contact
Substrate Thickness
Aluminum
Gold
R0202 and
T0303
B0202
0.020˝ ±0.001
(0.508mm ±0.025)
T0303 - Tapped network ½R + ½R
Bond Pad
Metallization
(0.762mm ±0.025)
0.030˝ ±0.001
½R
½R
Backside
0.030˝ ±0.001
(0.762mm ±0.025)
0.004˝ min bond pad size
Passivation
General Note
IRC reserves the right to make changes in product specification without notice or liability.
All information is subject to IRC’s own data and is considered accurate at time of going to print.
© IRC Advanced Film Division
• Corpus Christi Texas 78411 USA
Telephone: 361 992 7900 • Facsimile: 361 992 3377 • Website: www.irctt.com
A subsidiary of
TT electronics plc
WBC Series Issue January 2009 Sheet 1 of 3
TI TM4C123GXL data sharing
I have collected some information about TM4c123GXL and would like to share it with you. If you have any good information, please share it with us!...
wikelallala Microcontroller MCU
Measuring the reluctance problem
When measuring the magnetic resistance impedance value, the first test was more than 100K. After exchanging the multimeter probes, the test result was a few M. What caused this?...
928083047 Analog electronics
Electromagnetic compatibility design of flyback power factor correction circuit
Electromagnetic compatibility (EMC) refers to the ability of an electronic device or system to work properly in its electromagnetic environment and not cause unbearable electromagnetic interference to...
zbz0529 Power technology
Analog circuit behavior model and simulation based on Verilog-A_.pdf
Analog circuit behavior model and simulation based on Verilog-A_.pdf...
zxopenljx FPGA/CPLD
DCDC point circuit
Please ask everyoneDCDC point circuit, why do we need this port to adjust the frequency?Thanks for the advice!!...
15272693963 Circuit Observation Room
Can FPGA be used to design a GSM frequency selector?
I want to use FPGA to design a GSM digital frequency selector that can automatically select the frequency. I wonder if it is possible?...
yangms76 FPGA/CPLD

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 553  1506  2828  1861  2421  12  31  57  38  49 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号