SFP
www.vishay.com
Vishay Electro-Films
Thin Film Top-Contact Resistor with Part Mark
FEATURES
• Wire bondable
• Part marked - 5 digits
• Small size: 0.022 inches square
• Case: 0202
• Resistance range: 1
to 1 M
Product may not be to scale
The SFP series single-value resistor chips offer a small size,
wide ohmic value range and excellent power capacity.
The SFPs are part marked with resistance value allowing
user the ability to visually determine the resistance value of
the chip.
The SFPs are manufactured using Vishay Electro-Films (EFI)
sophisticated thin film equipment and manufacturing
technology.
The SFPs are 100 % electrically tested and visually
inspected to MIL-STD-883, method 2032 class H or K.
• DC power rating: 250 mW
• Oxidized silicon substrate for good power dissipation
• Resistor material: Tantalum nitride, self passivating
• Moisture resistant
APPLICATIONS
Vishay EFI SFP small resistor chips are widely used in hybrid
packages where space is limited and chip value marking is
important for identification. The die is part marked with the
resistance value. Wire bonding is made to the two pads on
the top of the chip.
TEMPERATURE COEFFICIENT OF RESISTANCE, VALUES, AND TOLERANCES
PARAMETER
Total Resistance Range
Standard Tolerances
TCR
VALUE
1 to 1M
± 0.1, ± 0.5, ± 1
± 25, ± 50, ± 100, ± 250
Tightest Standard Tolerance Available
1%
0.5 %
0.1 %
± 25 ppm/°C
± 50 ppm/°C
± 100 ppm/°C
± 250 ppm/°C
UNIT
%
ppm/°C
1
Ω
10
Ω
30
Ω
100
Ω
200 k
Ω
430 k
Ω
620 k
Ω
1 M
Ω
STANDARD ELECTRICAL SPECIFICATIONS
PARAMETER
Noise, MIL-STD-202, Method 308
100
- 250 k
< 100
or > 251 k
Moisture Resistance, MIL-STD-202, Method 106
Stability, 1000 h, + 125 °C, 125 mW
Operating Temperature Range
Thermal Shock, MIL-STD-202, Method 107, Test Condition F
High Temperature Exposure, + 150 °C, 100 h
Dielectric Voltage Breakdown
Insulation Resistance
Operating Voltage
DC Power Rating at + 70 °C (Derated to zero at + 175 °C)
5 x Rated Power Short-Time Overload, + 25 °C, 5 s
Note
• Values above 1M available
Revision: 15-Aug-11
1
For technical questions, contact:
efi@vishay.com
VALUE
- 35 typ.
- 20 typ.
± 0.5 max.
R/R
± 0.25 max.
R/R
- 55 to + 125
± 0.25 max.
R/R
± 0.5 max.
R/R
200
10
12
min.
100 V max.
0.250
± 0.25 max.
R/R
UNIT
dB
%
%
°C
%
%
V
V
W
%
Document Number: 61000
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT
www.vishay.com/doc?91000
SFP
www.vishay.com
DIMENSIONS
in inches
0.005
PART MARK
PART MARK
PART MARK
PART MARK
Vishay Electro-Films
PART MARK
PART MARK
PART MARK
PART MARK
0.018
0.022
TYPICAL RANGE
< 30
Ω
TYPICAL RANGE
30
Ω
to 199
Ω
TYPICAL RANGE
200
Ω
to 1 kΩ
TYPICAL RANGE
1 kΩ to 1 MΩ
0.004
SCHEMATIC
STANDARD MARKING - 5 DIGITS
XXXX
Four significant digits of value
X
Multiplier
C = 0.001
B = 0.01
A = 0.1
0=0
1 = 10
2 = 100
3 = 1000
MECHANICAL SPECIFICATIONS
PARAMETER
Chip Size
Chip Thickness
Chip Substrate Material
Resistor Material
Bonding Pad Size
Number of Pads
Pad Material
Backing
VALUE
0.022" x 0.022" ± 0.003" (0.558 mm x 0.558 mm ± 0.05 mm)
0.010" ± 0.002" (0.254 mm ± 0.05 mm)
Oxidized silicon, 10 kÅ minimum SiO
2
Tantalum nitride, self-passivating
0.004" x 0.004" (0.10 mm x 0.10 mm)
2
25 kÅ minimum aluminum (Au optional)
None, lapped semiconductor silicon (Au optional)
GLOBAL PART NUMBER INFORMATION
Global Part Number: SFP50000FKANHWS
Global Part Number Description: SFP 5K 1 % 100 ppm/°C Al None H WS
S
F
P
5
0
0
TOLERANCE
CODE
(%)
B
= 0.1
C
= 0.25
D
= 0.5
F
= 1.0
G
= 2.0
J
= 5.0
K
= 10.0
0
0
F
K
A
N
H
W
S
MODEL
SFP
22 x 22
size
Ta2N on
Silicon
w/ part
mark
RESISTANCE
First 4 digits
are significant
figures of
resistance
RESISTANCE
MULTIPLIER
CODE
C
= 0.001
B
= 0.01
A
= 0.1
0
=1
1
= 10
2
= 100
3
= 1000
TCR
(ppm/°C)
E
= ± 25
C
= ± 50
K
= ± 100
M
= ± 250
TERMINATION
G
= Au
A
= Al
BACK
METAL
G
= Au
N
= None
VISUAL
CLASS
H
= Class H
K
= Class K
PACKAGING
CODE
WS
=
Waffle pack
100 min., 1 mult
Revision: 15-Aug-11
2
For technical questions, contact:
efi@vishay.com
Document Number: 61000
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT
www.vishay.com/doc?91000
Legal Disclaimer Notice
www.vishay.com
Vishay
Disclaimer
ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE
RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively,
“Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other
disclosure relating to any product.
Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or
the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all
liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special,
consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular
purpose, non-infringement and merchantability.
Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical
requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements
about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular
product with the properties described in the product specification is suitable for use in a particular application. Parameters
provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All
operating parameters, including typical parameters, must be validated for each customer application by the customer’s
technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase,
including but not limited to the warranty expressed therein.
Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining
applications or for any other application in which the failure of the Vishay product could result in personal injury or death.
Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please
contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by
any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners.
Material Category Policy
Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as RoHS-Compliant fulfill the
definitions and restrictions defined under Directive 2011/65/EU of The European Parliament and of the Council
of June 8, 2011 on the restriction of the use of certain hazardous substances in electrical and electronic equipment
(EEE) - recast, unless otherwise specified as non-compliant.
Please note that some Vishay documentation may still make reference to RoHS Directive 2002/95/EC. We confirm that
all the products identified as being compliant to Directive 2002/95/EC conform to Directive 2011/65/EU.
Vishay Intertechnology, Inc. hereby certifies that all its products that are identified as Halogen-Free follow Halogen-Free
requirements as per JEDEC JS709A standards. Please note that some Vishay documentation may still make reference
to the IEC 61249-2-21 definition. We confirm that all the products identified as being compliant to IEC 61249-2-21
conform to JEDEC JS709A standards.
Revision: 02-Oct-12
1
Document Number: 91000
Talking about work
京公网安备 11010802033920号
EEWORLD
