ABL3-05.0000MHZ-S-N-7-W-T datasheet, PDF

Datasheet> All Categories > Passive components> Crystal/resonator> ABL3-05.0000MHZ-S-N-7-W-T

ABL3-05.0000MHZ-S-N-7-W-T: DescriptionSeries - Fundamental Quartz Crystal, 5MHz Nom, ROHS COMPLIANT, RESISTANCE WELDED, METAL, HC/49US, 2 PIN; CategoryPassive components Crystal/resonator; File Size1MB，3 Pages; ManufacturerAbracon; Websitehttp://www.abracon.com/index.htm; Environmental Compliance

Download Datasheet Parametric View All

ABL3-05.0000MHZ-S-N-7-W-T Overview

Series - Fundamental Quartz Crystal, 5MHz Nom, ROHS COMPLIANT, RESISTANCE WELDED, METAL, HC/49US, 2 PIN

ABL3-05.0000MHZ-S-N-7-W-T Parametric

Parameter Name	Attribute value
Is it Rohs certified?	conform to
Objectid	1928115654
package instruction	ROHS COMPLIANT, RESISTANCE WELDED, METAL, HC/49US, 2 PIN
Reach Compliance Code	compliant
Country Of Origin	Japan
YTEOL	5.95
Other features	AT CUT; TAPE AND REEL
Ageing	5 PPM/YEAR
Crystal/Resonator Type	SERIES - FUNDAMENTAL
Drive level	100 µW
frequency stability	0.0025%
frequency tolerance	15 ppm
Installation features	THROUGH HOLE MOUNT
Nominal operating frequency	5 MHz
Maximum operating temperature	85 °C
Minimum operating temperature	-30 °C
physical size	L11.5XB5.0XH2.0 (mm)/L0.453XB0.197XH0.079 (inch)
Series resistance	120 Ω
surface mount	NO

Preview

Download Datasheet

View All

HC/49US (AT49) MICROPROCESSOR CRYSTAL

ABL3 Series

FEATURES:

• Reduced height at 2.0mm

• High reliability & Low Cost

• Tight stability & extended temperature

• Proven resistance welded metal package

RoHS

Compliant

APPLICATIONS:

• Home electronics

• Computers, modems, and communications

• Automotive and industrial

• High-precision TCXO and clock applications

• Microprocessors

11.5 x 5.0 x 2.0 mm

| | | | | | | | | | | | | | |

STANDARD SPECIFICATIONS:

PARAMETERS

ABRACON P/N

Frequency

Operation Mode

ABL3 Series

3.579545 MHz to 70 MHz

AT cut (Fundamental or 3rd OT) or BT cut (See options)

3.579545MHz - 24.0MHz (Fundamental) (Standard)

24.01 - 70.00MHz (3rd- Overtone) (Standard)

24.01MHz - 50.00MHz (Fund. AT or BT) (See options)

0°C to + 70°C (see options)

- 55°C to + 125°C

± 50 ppm max. (see options)

See Table 1

7pF max.

18pF (see options)

1 mW max., 100µW typical

± 5ppm max.

500 M

Ω

min at 100Vdc ± 15V

1µW to 500µW

Change in frequency (Maximum - Minimum) over DLD range < ±10ppm

Change in ESR (Maximum - Minimum) over DLD range < 25% of Max ESR value

Maximum ESR over DLD range < Max ESR value

Operating Temperature

Storage Temperature

Frequency Tolerance at +25°C

Frequency Stability over the

Operating Temp. (Ref to +25°C)

Equivalent Series Resistance

Shunt Capacitance C

Load Capacitance C

Drive Level

Aging at 25°C ± 3°C Per Year

Insulation Resistance

Drive level dependency (DLD),

minimum 7 points tested

TABLE 1: ESR

FREQUENCY (MHz)

3.579 - 4.999 (Fund.)

5.000 - 5.999 (Fund.)

6.000 - 7.999 (Fund.)

8.000 - 8.999 (Fund.)

9.000 - 9.999 (Fund.)

10.000 - 15.999 (Fund.)

16.000 - 50.000 (Fund.)

24.01 - 31.999 (3rd O/T)

32.000 - 70.00 (3rd O/T)

ESR (Ω)

Ω

180

120

100

ABRACON IS

ISO 9001 / QS 9000

CERTIFIED

Revised:

09.01.10

30332 Esperanza, Rancho Santa Margarita, California 92688

tel 949-546-8000

fax 949-546-8001

| www.abracon.com

Visit www.abracon.com for Terms & Conditions of Sale

Recommended Resources

Concentrated Typical Circuit for Reference Voltage a

Simple RF LC filter circuit diagram

Fundamental frequency quartz crystal oscillator

On-site signal optical fiber transmission and reception circuit

555 high voltage low current low power inverter circuit

Application circuit of surface acoustic wave resonator in radio remote control

Newbie help with AD7745 issue: I want to measure the capacitance of a capacitive sensor, so I bought an AD7745. I was shocked when I bought it. I found that the chip is very small and it is difficult to solder it by hand. I would l...; 琉璃球 ADI Reference Circuit

Discussion on the problem caused by FPGA IO output signal resetting DSP and ARM circuit: Yesterday, when we were designing an FPGA board, we found an FPGA output reset circuit as follows:FPGA IO outputs TTL level. Now it is found that ARM and DSP work unreliably and there is a problem of ...; eeleader FPGA/CPLD

Request UJ7108 Datasheet: I have a broken multimeter (DT9808), which uses the UM7108 chip. Does anyone have information about it? Can you share it?...; huchuan987 Test/Measurement

How to use Keil simulation to see 4-way pwm, how to set the time, can clearly see the duty cycle, the screenshot effect is better!: How to use Keil simulation to see 4-way pwm, how to set the time, can clearly see the duty cycle, the screenshot effect is better!...; dongxinwanwu Microcontroller MCU

External pulse counting: If an IO port flips and generates a pulse, can it be counted and the edge polarity determined without turning on the external interrupt?...; sang523 stm32/stm8

Seeking to develop single chip microcomputer: Due to the needs of machine research and development, it is necessary to develop a single-chip microcomputer to judge and analyze the sound collected by the microphone, and then communicate with the P...; lzy8400367 MCU

Shortcut: S0 S1 S2 S3 S4 S5 S6 S7 S8 S9 SA SB SC SD SE SF SG SH SI SJ SK SL SM SN SO SP SQ SR SS ST SU SV SW SX SY SZ T0 T1 T2 T3 T4 T5 T6 T7 T8 T9 TA TB TC TD TE TF TG TH TI TJ TK TL TM TN TO TP TQ TR TS TT TU TV TW TX TY TZ U0 U1 U2 U3 U4 U6 U7 U8 UA UB UC UD UE UF UG UH UI UJ UK UL UM UN UP UQ UR US UT UU UV UW UX UZ V0 V1 V2 V3 V4 V5 V6 V7 V8 V9 VA VB VC VD VE VF VG VH VI VJ VK VL VM VN VO VP VQ VR VS VT VU VV VW VX VY VZ W0 W1 W2 W3 W4 W5 W6 W7 W8 W9 WA WB WC WD WE WF WG WH WI WJ WK WL WM WN WO WP WR WS WT WU WV WW WY X0 X1 X2 X3 X4 X5 X7 X8 X9 XA XB XC XD XE XF XG XH XK XL XM XN XO XP XQ XR XS XT XU XV XW XX XY XZ Y0 Y1 Y2 Y4 Y5 Y6 Y9 YA YB YC YD YE YF YG YH YK YL YM YN YP YQ YR YS YT YX Z0 Z1 Z2 Z3 Z4 Z5 Z6 Z8 ZA ZB ZC ZD ZE ZF ZG ZH ZJ ZL ZM ZN ZP ZR ZS ZT ZU ZV ZW ZX ZY

Popular Components