ATC GENERAL PURPOSE CAPACITORS: NPO (COG) DIELECTRIC
ELECTRICAL CHARACTERISTICS
CAPACITANCE RANGE:
0.5 pF to 0.10 µF.
TEMPERATURE CHARACTERISTIC:
0 ± 30ppm/°C.
L
W
OPERATING TEMPERATURE RANGE:
-55°C to +125°C.
DISSIPATION FACTOR:
0.1% (max.) @ + 25°C,
@1 MHz
≤
1000 pF; @1 KHz >1000 pF
INSULATION RESISTANCE
@ + 25°C and rated Vdc:
100,000 megohms (min.) or 1000 ohm-farads (min.),
whichever is less.
DIELECTRIC WITHSTANDING VOLTAGE:
250% of rated voltage for 5 ± 1 seconds, 50 milliamps (max.).
Unless otherwise specified all test data is at + 25°C.
T (MAX.)
MB
Temperature Coefficient
Aging Rate
Voltage Coefficient of Capacitance
Temperature (Celsius)
Impedance vs. Frequency
Dissipation Factor vs. Frequency
Minimum IR vs. Temperature
Temperature (Celsius)
Sales of ATC products are subject to the terms and conditions contained in American Technical Ceramics Corp. Terms and Conditions of Sale(ATC document #001-992 Rev. A 10/03). Copies of
these terms and conditions will be provided upon request. They may also be viewed on ATC's website at www.atceramics.com/productfinder/default.asp. Click on the link for Terms and
Conditions of Sale.
ATC has made every effort to have this information as accurate as possible. However, no responsibility is assumed by ATC for its use, nor for any infringements of rights of third parties which
may result from its use. ATC reserves the right to revise the content or modify its product without prior notice.
After AD sampling, if there is no DA chip, how can we view the results after AD? And how can we use an oscilloscope to observe the results after FFT changes? How can we display the array values inside...
[b][backcolor=white] [/backcolor][/b][align=left][color=rgb(0, 0, 0)][font=宋体][size=16px]1. The relationship between stages of a multi-stage amplifier: [/size][/font][/color][/align][align=left][color...
[i=s]This post was last edited by dontium on 2015-1-23 11:38[/i] In recent years, Sigma-Delta architecture is becoming more and more important and popular for implementing high-resolution ADC in mixed...
[i=s]This post was last edited by isduhfufa on 2022-10-19 21:13[/i]Where Vout is the output voltage, Vf is the voltage drop of the rectifier diode at the output end, Vin (minDC) is the minimum input v...
I am a novice in the field of communications. I have recently been working on a project related to digital walkie-talkies and designing an application layer software for sending and receiving text mes...
1. Introduction
Since the 1980s, with the continuous development of automotive electronic technology, there are more and more electronic control units in automobiles, such as electronic fuel i...[Details]
Since the No. 4 blast furnace of Handan Iron and Steel was put into operation in 1993, its external equipment has been seriously aged, and the original PLC control system TDC3000 of the hot blast furn...[Details]
At very low temperatures, certain metals and alloys lose their resistance to electric
current
and become
superconductors
. Two parameters that are often measured are the transition ...[Details]
System Overview
The system consists of a signal preprocessing circuit, a single-chip computer AT89C2051, a systematic LED display module, a serial port data storage circuit and system software...[Details]
0 Introduction
There are many types of sensors, and the working principles, measurement targets and measurement environments of different types of sensors vary greatly. The corresponding detection s...[Details]
The demand for improved healthcare environments is endless, so medical imaging equipment with higher resolution is needed to better observe the human body. High resolution brings problems with sign...[Details]
One in five car failures are caused by batteries, a problem that will become more serious in the coming years as electric-by-wire, start/stop engine management and hybrid (electric/gas) vehicles be...[Details]
Battery clamps, commonly known as battery connectors, come in two sizes depending on the thickness of the battery terminals. One is the battery clamp used on thick terminals, with a positive termin...[Details]
Electrostatic coupling and interference occur when a charged object is close to the input of the circuit being measured. At low impedance, the effects of interference are not noticeable because th...[Details]
In industry, voltage 0…5 (10) V or current 0 (4)…20 mA is usually used as a method for analog signal transmission, which is also a method often used by programmable controllers. So what are the dif...[Details]
DCDC means DC to DC (conversion of different DC power values). Anything that meets this definition can be called a DCDC converter. Specifically, it means converting the input DC into AC through a s...[Details]
This paper describes the design method of electronic multifunctional watt-hour meter, the key technology of hardware design and the software design process. Taking NEC's μPD78F0338 microcontroller ...[Details]
Preface
DS18B2 is generally used in conjunction with a single-chip microcomputer, and there are few reports on
the interface between
DSP
and DS18B20. Therefore, this article introdu...[Details]
introduction
Frequency characteristic tester
Also known as sweep frequency meter or frequency response analyzer, it uses a rectangular oscilloscope with internal scale as
a displ...[Details]
The embedded network module series products of Yingchuang Company all have a streamlined ISA expansion bus, which usually includes several address buses, 8-bit data buses, read and write control li...[Details]
DSP and ARM Processors
京公网安备 11010802033920号
EEWORLD
