Component Carriers and Housings
Weidmüller DK 4 and DKT 4 terminals
are suitable for the installation of electronic
components with a maximum diameter or
width of 4.5 mm. Four independent clamp-
ing yoke screw connections are available.
A snap-on frame expands the installation
space in the DK4 by 6 mm respectively.
Depending on type, these modular termi-
nals are suitable for mounting on TS 32,
TS 35 x 7.5 or TS 35 x 15 mounting rails
according to European standards EN 50
035 and EN 50 022.
Weidmüller EG 4 housing
as type EG 3, offers the same width of
22.5 mm. However, the greater installation
depth (75 mm) and height (109 mm) allow
the installation of more complex circuit
configurations. The built-in installation can
be connected via 6 screw connections.
The snap-on combination foot allows the
terminal to be mounted on TS 32, TS 35 x
7.5 or TS 35 x 15 mounting rails. Due to
the sliding foot construction, the EG 4 can
be slid forwards or backwards on the
locking foot, and can be turned through
180° (e.g. exchanging of input and out-
put).
Weidmüller housings type WAVEBOX
It is essential to provide fit-for-use housings
for modern electronic components. Setting
and control functions must be easily car-
ried out and technical requirements with
respect to heat dissipation and EMV prop-
erties should be supported.
An ideal design saves space and wiring
costs in the switchgear cabinet.
In addition, ergonomics and design are
becoming increasingly important for high-
quality electronic products.
These are the criteria that led to the devel-
opment of WAVEBOX. Simplified produc-
Weidmüller WDK 2.5 terminals
tion methods (shaft soldering, SMD) ensure
are suitable for the installation of electrical
cost-savings for the customer.
components with a maximum width of 4
The WAVEBOX is characterised by:
Weidmüller EG 5 housings
mm. As many as four independent clamp-
• Optimum width for any application
ing yoke screw connections or 4 6.3 x 0.8 correspond to type EG 4. The EG 5 has
(12.5 mm, 17.5 mm, 22.5 mm)
tab connections are available. These termi- 12 screw connections, which can be wired • Large component assembly surface;
nals are suitable for mounting on TS 35 x
with solder lugs inside the housing. The
SMDs can be mounted on the solder
7.5 or TS 35 x 15 mounting rails.
snap-on combination foot allows the ter-
side
minal to be mounted on TS 32, TS 35 x
• UL94 flammability class V2
7.5 or TS 35 x 15 mounting rails. Due to
• No tools required for assembly
Weidmüller EG 1 housings
the sliding foot construction, the EG 4 can • Plug-in printed circuit board
offer 4 screw connections and, as acces-
be slid 6 mm forwards or backwards on
• Plug-in cross-connection via ZQV 2.5 N
sories, up to 4 0.8 x 4.8 mm solder/tab
the engaging foot and can be turned
• Hinged, transparent cover
connections on a width of 18 mm. The
through 180° (e.g. exchanging input and
• BLZ 5.08 screw/plug and socket con-
screw clamp busbar ends with a solder
output).
nector
ring inside the housing. Two end plates
• BLFZ 5.08 optional tension clamp/plug
seal the module. Depending on type, the
and socket connector
Weidmüller EG 6 housings
modules are mounted on TS 32, TS 35 x
• Marking option with WS tags
7.5 or TS 35 x 15 mounting rails.
have a bus-suitable contact carrier. The
• Mounts onto TS 35
bus connection is created by directly
Weidmüller individual parts for RS 70
mounting several housings in a row. 32
locking socket
Weidmüller EG 2 housings
connections are available on both sides of
latch together to form units from 20 mm in
The external shape of these housings cor- the housing as crimp connector block
width. Any desired intermediate parts or
responds to Type EG 1. Four screw con-
contacts. The housing accepts printed cir-
feet can be connected between two side
nections or up to 8 0.8 x 6.6 mm/0.8 x
cuit boards with dimensions of 100 x 120
pieces (locking feet) at intervals of 5 mm. In
2.8 mm tab connectors are connected
mm. The printed circuit board is adapted
this way, a carrier module is constructed
with a printed circuit board in the housing. with a VG 64 DIN strip. The front panel is
for PCB, on which various components
They can be mounted on TS 32, TS 35 x
screwed onto the circuit board similar to
can be soldered. The assembly snaps onto
7.5 or TS 35 x 15 mounting rails.
the 19" technology. The locking foot
TS 32, TS 35 x 7.5 or TS 35 x 15 mount-
allows easy mounting onto the TS 35
ing rails.
mounting rail.
Weidmüller EG 3 housings
The Weidmüller RSX custom circuit
provides 6 screw connections or 12
module
Weidmüller SEG/U housing
0.8 x 6.3 mm/0.8 x 2.8 mm tab connec-
is a largely prefabricated unit wich accepts
tions on a width of 22.5 mm. As an acces- enable the plug-in module assembly of a
up to 5 components such as resistors,
sory, Weidmüller offers a shaped printed
70 x 52 x 1 mm printed circuit board. The diodes, varistors or capacitors via soldering
circuit board with a 2.54 mm hole grid
circuit board is attached to the accessory
terminals. The components are connected
or fully copper-coated. The engagable
cover plate via snap-in hooks. The housing via screw clamps or tab connections. This
combination foot allows the terminal to
contains a 13-pole socket block for instal- module is also suitable for mounting on TS
be mounted on TS 32, TS 35 x 7.5
lation of the module; 6 screw connections 32, TS 35 x 7.5 or TS 35 x 15 mounting
or TS 35 x 15 mounting rails.
are available for connection. The permissi- rails.
The MPL mounting plate is used to mount ble power loss in the housing during con-
Weidmüller locking socket profiles
the housing directly (without mounting rail). tinuous operation of terminals in rows
The RS 45, RS 80 and RS 100 profiles are
Due to the sliding foot construction, the
amounts to 1.5W, depending on the sur-
available as 2 m long strips. The extruded
EG 3 can be turned through 180° in all
face temperature of the soldered compo-
profiles can be easily cut to any length with
types of assembly (e.g. exchanging input
nents. The snap-on combination foot
and output).
allows the housings to be mounted on TS a saw. In this way, a carrier module is con-
structed for a printed circuit board on
32, TS 35 x 7.5 or TS 35 x 15 mounting
which various components can be solder-
rails.
ed. Locking feet can be slid into these pro-
files for mounting on TS 32, TS
35 x 7.5 or TS 35 x 15 mounting rails. The
sliding foot construction of the RS 80 also
allows the fixing foot be turned through 180°.
293
Housings
京公网安备 11010802033920号
EEWORLD
