NOTES: (1) Binary Two’s Complement coding. (2) Ratio of (Distortion
RMS
+ Noise
RMS
)/Signal
RMS
. (3) D/A converter output frequency/signal level (both left and right
channels are “on”). (4) D/A converter sample frequency (8 x 44.1kHz; 8X oversampling per channel). (5) Ratio of Noise
RMS
/Signal
RMS
. Measured using a 40kHz
3rd-order GIC (Generalized Immittance Converter) filter and an A-weighted filter. (6) Bipolar Zero.
USA OEM PRICES
The information provided herein is believed to be reliable; however, BURR-BROWN assumes no responsibility for inaccuracies or omissions. BURR-BROWN assumes
no responsibility for the use of this information, and all use of such information shall be entirely at the user’s own risk. Prices and specifications are subject to change
without notice. No patent rights or licenses to any of the circuits described herein are implied or granted to any third party. BURR-BROWN does not authorize or warrant
any BURR-BROWN product for use in life support devices and/or systems.
®
PCM67/69A
2
PIN ASSIGNMENTS
PCM67P
PCM67U
DESCRIPTION
+5V Analog Supply Voltage
Left Voltage Common
No Connection
Left Current Output (0 to 1.2mA)
Servo Decoupling Capacitor
Reference Decoupling Capacitor
Right Current Output (0 to 1.2mA)
No Connection
Right Voltage Common
Analog Common
Digital Common
Mode Control 2
Right Data Input
Bit Clock
System Clock
Word Clock
Left Data Input
Mode Control 3
Mode Control 1
+5V Digital Supply Voltage
MNEMONIC
+V
A
LV
COM
NC
LI
OUT
SRVCAP
REFCAP
RI
OUT
NC
RV
COM
ACOM
DCOM
MC2
RDATA
BTCK
SYSCK
WDCK
LDATA
MC3
MC1
+V
D
PCM69AP PCM69AU
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
ABSOLUTE MAXIMUM RATINGS
+V
A
, +V
D
to ACOM, DCOM ................................................... 0V to +6.5V
ACOM to DCOM ...............................................................................
±0.5V
Digital Inputs to DCOM ............................................ –0.3V to +V
D
+ 0.3V
Power Dissipation ................ 300mW (U Package), 500mW (P Package)
Lead Temperature, (soldering, 10s) .............................................. +260°C
Max Junction Temperature ............................................................ +165°C
NOTE: Stresses above those listed under “Absolute Maximum Ratings”
may cause permanent damage to the device. Exposure to absolute
maximum conditions for extended periods may affect device reliability.
ELECTROSTATIC
DISCHARGE SENSITIVITY
Electrostatic discharge can cause damage ranging from per-
formance degradation to complete device failure. Burr-Brown
Corporation recommends that all integrated circuits be handled
and stored using appropriate ESD protection methods.
PACKAGE INFORMATION
MODEL
PCM67P/69AP
PCM67U/69AU
PACKAGE
16-Pin Plastic DIP
20-Pin SOIC
PACKAGE DRAWING
NUMBER
(1)
180
248
NOTE: (1) For detailed drawing and dimension table, please see end of data
Our school is going to divide the subjects. I have been in class for half a year. I have learned HTML, Javascript, C language, Oracle, Java, and C# from beginning to end. Of course, these are the elem...
In response to [i]mesada[/i]'s post [url=https://bbs.eeworld.com.cn/thread-341066-1-1.html]https://bbs.eeworld.com.cn/thread-341066-1-1.html[/url], hehe, although he seems to have disappeared, he is a...
In learning, teachers are a very critical link. This is certainly no exception for embedded learning. Therefore, in embedded learning, teachers are one of the most important factors. What kind of teac...
Hello, moderators and faga engineers, are you interested in practicing the program of downloading pictures? You can also learn the top-level file by yourself. The following is lined up. First of all, ...
UBOOT ran smoothly and succeeded at once, but the LINUX transplantation died on the initialization clock interrupt. I racked my brains and checked a lot of information but to no avail. The hardware pl...
This program is written to simulate the serial port hardware mechanism. When used, a timed interrupt can be set with a time interval of 1/4 baud rate. The receiving function is called once for ea...[Details]
In
circuit design,
current
measurement
is widely used, and the main fields are divided into three categories: in measurement,
the electric meter
is used to measure the curre...[Details]
0. Introduction
In daily life, we often see some special-purpose vehicles. When these vehicles pass through intersections, they often obtain the right of way at intersections by temporarily op...[Details]
The Portable Digital Data Acquisition System (PDDAS) uses LabVIEW Real-Time and PXI to control the wind tunnel test and record air pressure data from 128 different channels.
"The LabVIEW Real-...[Details]
All electronic design engineers and scientists have performed electrical signal analysis, or signal analysis for short. Through this basic measurement, they can gain insight into signal details and...[Details]
DSP (digital signal processor) is used more and more frequently in today's engineering applications. There are three main reasons for this: first, it has powerful computing power and is capable of ...[Details]
My colleague and I spent the day chatting in the hotel bar. We had met with several customers. We were both wondering how come these engineers we were meeting knew almost nothing about analog techn...[Details]
1. Introduction
At present, most lighting equipment still uses traditional energy for lighting. Making full use of solar energy as the energy supply for lighting equipment is of great si...[Details]
AD8205 is
a single-supply high-performance differential
amplifier
launched by
Analog
Devices of the United States
. The typical single-supply voltage is 5V, and its common-mode volta...[Details]
Overview:
This paper introduces a method of connecting a CAN-bus network with Ethernet to form a medium-sized remote monitoring/data transmission network.
CAN (Controller Area Network) is ...[Details]
On the afternoon of July 10, Beijing time, Taiwan's largest chip designer MediaTek expects its smartphone chip shipments to grow by double digits in the third quarter of this year, and the company is ...[Details]
In the analysis of electronic circuits, static analysis (also known as DC analysis) is the basis of circuit analysis. However, it is well known that electronic components are nonlinear, so the anal...[Details]
RS-422 and RS-485 are both serial data interface standards, which were developed and published by the Electronic Industries Association (EIA). RS-422 defines a balanced communication interface with a ...[Details]
Many battery-powered systems require a visual indicator to show when the battery needs to be replaced. LEDs are commonly used for this purpose, but they consume at least 10mA of current. This con...[Details]
With concerns about the growing energy crisis, motor efficiency has become an important and timely topic. This is because motors use 63% to 70% of the electricity produced in the United States and ...[Details]
Embedded System
京公网安备 11010802033920号
EEWORLD
