EEWORLDEEWORLDEEWORLD

Part Number

Search

8N4Q001FG-0080CDI8

Description
IC osc clock QD freq 10clcc
Categorysemiconductor    Analog mixed-signal IC   
File Size163KB,20 Pages
ManufacturerIDT (Integrated Device Technology, Inc.)
Websitehttp://www.idt.com/
Download Datasheet View All

8N4Q001FG-0080CDI8 Online Shopping

Suppliers Part Number Price MOQ In stock  
8N4Q001FG-0080CDI8 - - View Buy Now

8N4Q001FG-0080CDI8 Overview

IC osc clock QD freq 10clcc

Quad-Frequency Programmable XO IDT8N4Q001 REV G
DATA SHEET
General Description
The IDT8N4Q001 is a Quad-Frequency Programmable Clock
Oscillator with very flexible frequency programming capabilities. The
device uses IDT’s fourth generation FemtoClock® NG technology for
an optimum high clock frequency and low phase noise performance.
The device accepts 2.5V or 3.3V supply and is packaged in a small,
lead-free (RoHS 6) 10-lead ceramic 5mm x 7mm x 1.55mm package.
Besides the four default power-up frequencies set by the FSEL0 and
FSEL1 pins, the IDT8N4Q001 can be programmed via the I
2
C
interface to output clock frequencies between 15.476MHz to
866.67MHz and from 975MHz to 1,300MHz to a very high degree of
precision with a frequency step size of 435.9Hz ÷
N
(N is the PLL
output divider). Since the FSEL0 and FSEL1 pins are mapped to four
independent PLL divider registers (P, MINT, MFRAC and N),
reprogramming those registers to other frequencies under control of
FSEL0 and FSEL1 is supported. The extended temperature range
supports wireless infrastructure, telecommunication and networking
end equipment requirements.
Features
Fourth generation FemtoClock® NG technology
Programmable clock output frequency from 15.476MHz to
866.67MHz and from 975MHz to 1,300MHz
Four power-up default frequencies (see part number order
codes), re-programmable by I
2
C
I
2
C programming interface for the output clock frequency and
internal PLL control registers
Frequency programming resolution is 435.9Hz ÷N
One 2.5V, 3.3V LVDS clock output
Two control inputs for the power-up default frequency
LVCMOS/LVTTL compatible control inputs
RMS phase jitter @ 156.25MHz (12kHz - 20MHz): 0.253ps
(typical), integer PLL feedback configuration
RMS phase jitter @ 156.25MHz (1kHz - 40MHz): 0.263ps
(typical), integer PLL feedback configuration
Full 2.5V or 3.3V supply modes
-40°C to 85°C ambient operating temperature
Available in Lead-free (RoHS 6) package
Block Diagram
OSC
f
XTAL
÷MINT,
MFRAC
2
25
FSEL1
FSEL0
SCLK
SDATA
OE
Pulldown
Pulldown
Pullup
Pullup
Pullup
Pin Assignment
÷P
PFD
&
LPF
FemtoClock® NG
VCO
1950-2600MHz
÷N
Q
nQ
DNU 1
OE 2
GND 3
FSEL0 4
FSEL1 5
10 SCLK
9 SDATA
8 V
DD
7 nQ
6 Q
7
Configuration Register (ROM)
(Frequency, APR, Polarity)
I
2
C Control
IDT8N4Q001
10-lead ceramic 5mm x 7mm x 1.55mm
package body
CD Package
Top View
IDT8N4Q001GCD
REVISION A
MARCH 6, 2012
1
©2012 Integrated Device Technology, Inc.
New Qualcomm QCA4010 Development Board Exchange
[i=s]This post was last edited by qwerghf on 2016-7-18 14:29[/i] I just bought a [color=rgb(85, 85, 85)][font=arial, Microsoft YaHei][size=2]Qualcomm QCA4010 development board,[/size][/font][/color][c...
qwerghf Buy&Sell
Microcontroller selection
STM32, which 48-pin model can support I2S and USB communication? I can't find Chinese MCU information...
~胖球 stm32/stm8
F2812 interrupt priority setting (reprinted)
F2812 interrupt priority settingAuthor: embededt… Article source: embededtonyViews :103 Update time: 2011-4-20I thought the 2812 interrupts could not set the priority. In fact, the hardware priority i...
安_然 Microcontroller MCU
Made a tool to use serial port IAP to realize batch online upgrade program
After the product is produced, it may be necessary to upgrade the software in large quantities, so a tool for batch upgrading programs is developed.Two upgrade cases for STM32 and M0518 are provided....
ap0705307 MCU
[My relationship with TI] + LMX2541SQ3740E phase-locked loop debugging
[size=4] Most of the forums use TI's MCU and power products, so I won't talk about them. In my work, I still use a lot of TI devices, such as power supplies, ADCs, DACs, level converters, phase-locked...
neufeifatonju TI Technology Forum
【allegro】Geber cannot come out due to special-shaped hole
Hello everyone, I have three special-shaped holes, why didn't they come out when I was importing the GERBER?...
ohahaha PCB Design

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 546  655  13  248  1307  11  14  1  5  27 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号