EEWORLDEEWORLDEEWORLD

Part Number

Search

PH1-FLPFC3085

Description
Transponder, 10660Mbps(Tx), 10660Mbps(Rx), FC/UPC Connector,
CategoryWireless rf/communication    Optical fiber   
File Size240KB,6 Pages
ManufacturerLumentum Operations LLC
Download Datasheet Parametric View All

PH1-FLPFC3085 Overview

Transponder, 10660Mbps(Tx), 10660Mbps(Rx), FC/UPC Connector,

PH1-FLPFC3085 Parametric

Parameter NameAttribute value
Objectid4000959762
Reach Compliance Codecompliant
Other featuresIT ALSO OPERATE FROM 1280NM TO 1600NM
body height13.2 mm
Body length or diameter84.1 mm
Connection TypeFC/UPC CONNECTOR
Data rate (receive)10660 Mbps
Data rate (send)10660 Mbps
Emitter/Detector TypePIN PHOTODIODE
Fiber optic equipment typesTRANSCEIVER, TRANSPONDER
Nominal operating wavelength1538 nm
Nominal optical power output1.584 mW
minimum return loss-27 dB
Sensitivity-17 dBm
COMMUNICATIONS MODULES & SUBSYSTEMS
10 Gb/s TDM/DWDM 300 Pin SFF MSA SR2/IR2/LR2 Transponder
PH1 Series
Key Features
• Three configurations supporting SR2/IR2/LR2 applications
• Supports dense wavelength division multiplexing
(DWDM) applications (without wavelocker)
• Microprocessor controls to support I2C
• Integrated 16:1/1:16 mux/demux
• Small form factor package (2.2" x 3.0" x 0.53") for high
density applications
• Low power consumption: 4.8 W typical, 6.8 W maximum
for TDM applications
• 70 °C maximum operating temperature
• High sensitivity PIN or APD receivers
• SONET, FEC, Ethernet and Multirate Capable Versions
• Forward, counter and line timing clocking modes
Applications
Telecommunications
Metropolitan Area Networks
Subscriber loop
Intra-office SONET/SDH
High bit-rate data communications
JDSU 10 Gb/s PH1 Series transponders are intended for 1550 nm system
applications with reaches of up to 80 km. The series includes three different
transponders for SR2 (25 km), IR2 (40 km), and LR2 (80 km) TDM or DWDM
applications. Each transponder accepts 16 bits of parallel digital data and converts
it to a 10 Gb/s NRZ modulated optical signal. It also accepts a 10 Gb/s NRZ
modulated optical signal and converts it into 16 bit wide parallel digital data.
The PH1 series offers low DC power dissipation and is available in either a small
form factor package (2.2 x 3 x 0.53 inches) or in a larger footprint (3.5 x 4.5 x 0.53
inches) package, depending on system thermal performance requirements. The
transmit design uses an Electro-Absorptive Modulated Laser (EML) which,
depending on the configuration, produces an average output power of between
-4 dBm to 2 dBm (EOL). A PIN (-17 dBm typical sensitivity) or APD (-24 dBm
typical sensitivity) receiver is available, based on system configurations.
JDSU PH1 Series transponders are designed to support the following data rates:
9.953 Gb/s (SONET), 10.3125 Gb/s (Ethernet), 10.664 Gb/s (FEC Encoded),
10.709 Gb/s FEC, or 11.09 Gb/s EFEC. They meet all applicable SONET/SDH standards.
Compliance
• Telcordia GR-253-Core
NORTH AMERICA
:
800 498-JDSU (5378)
WORLDWIDE
:
+800 5378-JDSU
WEBSITE
:
www.jdsu.com
WinCE6.0 is very different from WinCE5.0. Please introduce WinCE6.0 (including: directory structure...)
WinCE6.0 is very different from WinCE5.0. Please introduce WinCE6.0 (including: directory structure...)...
lisheng053758 Embedded System
About DS-5 debugging bare board FPGA
According to Section 7.4 of the DE1-SOC training material, to light up the FPGA LED, you need to go through the following steps:alt_fpga_control_enable() , allow the HPS to control the FPGA;alt_fpga_c...
guorui200901 FPGA/CPLD
VHDL frequency division
My crystal is 50M, and after PLL division, there is still 10M. I want to make a clock now, that is, to get a 1HZ signal. That is difficult. I wrote several processes and divided it three times, but I ...
wenhuawu FPGA/CPLD
[ESP32-Audio-Kit Audio Development Board] - 4: Run "esp-adf" build on Ubuntu 20.04
[i=s]This post was last edited by MianQi on 2021-10-7 21:51[/i]Things to note and set up include: 1. Download-unzip " esp-idf-v4.2.2.zip" (https://github.com/espressif/esp-idf/releases/tag/v4.2.2) (ht...
MianQi RF/Wirelessly
at91rm9200 u-boot burning problem
I want at91rm9200 to boot from flash. I see the partition table. I need to burn boot.bin, u-boot.gz, uImage, and finally the u-boot environment variables. Where can I find the boot.bin and environment...
lijiamin11 Embedded System
Why is serial faster than parallel?
Last week we sent out a 32G USB flash drive in an event. People also shared their comparison of the transmission speed of this USB flash drive on the forum. Some people questioned that USB only relies...
eric_wang Integrated technical exchanges

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 418  2601  99  1934  1914  9  53  2  39  37 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号