EEWORLDEEWORLDEEWORLD

Part Number

Search

PH1-MLASA2805

Description
Transponder, 10709Mbps(Tx), 10709Mbps(Rx), SC/UPC Connector,
CategoryWireless rf/communication    Optical fiber   
File Size240KB,6 Pages
ManufacturerLumentum Operations LLC
Download Datasheet Parametric View All

PH1-MLASA2805 Overview

Transponder, 10709Mbps(Tx), 10709Mbps(Rx), SC/UPC Connector,

PH1-MLASA2805 Parametric

Parameter NameAttribute value
Objectid4000967176
Reach Compliance Codecompliant
Other featuresIT ALSO OPERATE FROM 1280NM TO 1600NM
body width56.1 mm
body height13.2 mm
Body length or diameter76.5 mm
Connection TypeSC/UPC CONNECTOR
Data rate (receive)10709 Mbps
Data rate (send)10709 Mbps
Emitter/Detector TypeAVALANCHE PHOTODIODE
Fiber optic equipment typesTRANSCEIVER, TRANSPONDER
Nominal operating wavelength1533 nm
Nominal optical power output1.584 mW
minimum return loss-27 dB
Sensitivity-24 dBm
COMMUNICATIONS MODULES & SUBSYSTEMS
10 Gb/s TDM/DWDM 300 Pin SFF MSA SR2/IR2/LR2 Transponder
PH1 Series
Key Features
• Three configurations supporting SR2/IR2/LR2 applications
• Supports dense wavelength division multiplexing
(DWDM) applications (without wavelocker)
• Microprocessor controls to support I2C
• Integrated 16:1/1:16 mux/demux
• Small form factor package (2.2" x 3.0" x 0.53") for high
density applications
• Low power consumption: 4.8 W typical, 6.8 W maximum
for TDM applications
• 70 °C maximum operating temperature
• High sensitivity PIN or APD receivers
• SONET, FEC, Ethernet and Multirate Capable Versions
• Forward, counter and line timing clocking modes
Applications
Telecommunications
Metropolitan Area Networks
Subscriber loop
Intra-office SONET/SDH
High bit-rate data communications
JDSU 10 Gb/s PH1 Series transponders are intended for 1550 nm system
applications with reaches of up to 80 km. The series includes three different
transponders for SR2 (25 km), IR2 (40 km), and LR2 (80 km) TDM or DWDM
applications. Each transponder accepts 16 bits of parallel digital data and converts
it to a 10 Gb/s NRZ modulated optical signal. It also accepts a 10 Gb/s NRZ
modulated optical signal and converts it into 16 bit wide parallel digital data.
The PH1 series offers low DC power dissipation and is available in either a small
form factor package (2.2 x 3 x 0.53 inches) or in a larger footprint (3.5 x 4.5 x 0.53
inches) package, depending on system thermal performance requirements. The
transmit design uses an Electro-Absorptive Modulated Laser (EML) which,
depending on the configuration, produces an average output power of between
-4 dBm to 2 dBm (EOL). A PIN (-17 dBm typical sensitivity) or APD (-24 dBm
typical sensitivity) receiver is available, based on system configurations.
JDSU PH1 Series transponders are designed to support the following data rates:
9.953 Gb/s (SONET), 10.3125 Gb/s (Ethernet), 10.664 Gb/s (FEC Encoded),
10.709 Gb/s FEC, or 11.09 Gb/s EFEC. They meet all applicable SONET/SDH standards.
Compliance
• Telcordia GR-253-Core
NORTH AMERICA
:
800 498-JDSU (5378)
WORLDWIDE
:
+800 5378-JDSU
WEBSITE
:
www.jdsu.com
【Nucleo】My STM32F05 Nucleo is now working
I used the board I bought in a group purchase for 39 yuan and found it very good. I drew a circuit and started making the board. So I never talked about my experience. Now the board is back and I'm re...
dontium stm32/stm8
After installing the SDK, run setup.sh
Run setup.sh, but after executing uboot setup, the question "Which kernel image do you want to boot from TFTP?" pops up. After clicking Enter, it stays there and I cannot exit....
wnwolf ARM Technology
uVision2 Getting Started Tutorial
uVision2 Getting Started Tutorial...
wang7588038 MCU
High speed op amp self-excitation
High-speed op amp self-excitation solution...
成杨 Analog electronics
I didn't ask for the meter back, but I found out that the electricity was stolen.
Poor me, my electricity has been stolen for a long time. Remember the incident of children being hacked? It was at that time that the school installed cameras. They actually connected my home wires wi...
wangfuchong Talking
vb mscomm and embedded system serial port communication, old computer communication is not normal?
Now I use vb mscomm to communicate with the program on Linux, using the standard mode instead of the original mode (raw). The program on the Linux wrench does this: bzero(&newtio, sizeof(newtio)); ///...
someoneelse Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1804  759  2181  826  2300  37  16  44  17  47 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号