EEWORLDEEWORLDEEWORLD

Part Number

Search

177-710-5-67GP6K5-18LXG

Description
Cable Assembly, 26AWG,
CategoryThe connector    Connector bracket   
File Size858KB,5 Pages
ManufacturerGlenair
Websitehttp://www.glenair.com/
Download Datasheet Parametric View All

177-710-5-67GP6K5-18LXG Overview

Cable Assembly, 26AWG,

177-710-5-67GP6K5-18LXG Parametric

Parameter NameAttribute value
Objectid7004970315
Reach Compliance Codeunknown
YTEOL8.75
Other featuresSTANDARD: MIL-DTL-83513, EMI SHIELDED
CertificationMIL
Conductor surface treatmentSILVER
conductor materialCOPPER
ConnectorSide1MICRO-D MALE
ConnectorSide2MICRO-D MALE
Connector bracket typeCABLE ASSEMBLY
structureSTRANDED
Cross-sectional area0.129 mm2
DIN complianceNO
IEC complianceNO
insulator materialPOLYTETRAFLUOROETHYLENE
Jacket materialETHYLENE-CHLOROTRIFLUOROETHYLENE
length0.466 mm
MIL complianceYES
Number of conductors67
Maximum operating temperature150 °C
Minimum operating temperature-55 °C
Rated current3 A
Rated voltage150 V
resistance0.125 Ω
shieldYES
stay19X38
Wire gauge26 AWG
Wire and Cable NamesFLEXIBLE CORD AND FIXTURE WIRE
B
SHIELDING EFFECTIVENESS (Db)
1.00E+04
1.00E+05
1.00E+06
1.00E+07
1.00E+08
1.00E+09
SHIELDING EFFECTIVENESS (Db)
Micro-D Harness
EMI Performance with Ground Spring
100
90
80
70
60
50
40
30
20
10
0
1.00E+03
MWDM Micro-D
Shielded Cable Assembly
Single-Ended or Double-Ended–These
easy-to-order cable
assemblies eliminate the need for expensive assembly labor. 100%
tested and ready for use.
Now With Twisted Pairs–No
need to create a procurement
specification for Micro-D cables with twisted pairs. Glenair 177-740
cables are furnished with a full complement of white/blue twisted
pair wires.
Integral Shield Termination–The
connector shell has a platform
to accept Band-It shield termination bands. The cable shield braid is
attached directly to the connector.
Save Labor, Reduce Weight and Improve EMI Shielding
with Glenair’s Micro-D Shielded Cable Assemblies
Aerospace electronics systems require higher and higher levels of protection from radiated emissions. Glenair’s
fully shielded Micro-D cable assemblies meet this need. The cable shield is attached directly onto the one-
piece connector shell and secured with a stainless steel
Band-Master™ ATS
clamp. These pre-wired, 100% tested
assemblies meet the requirements of MIL-DTL-83513. An optional ground spring on the pin connector assures low
shell-to-shell resistance. Available with a variety of wire types and shields, Micro-D shielded assemblies can be
ordered in any length, either single-ended or “back-to-back”.
Ground Spring and EMI Shielding Effectiveness
A gold-plated stainless steel ground spring on the pin connector mating
face offers substantial improvement in EMI protection. The graphs
compare identical connectors tested with and without ground springs.
EMI Performance without Ground Spring
100
90
80
70
60
50
40
30
20
10
0
1.00E+03
1.00E+04
1.00E+05
1.00E+06
1.00E+07
1.00E+08
1.00E+09
frequency (Hz)
frequency (Hz)
© 2013 Glenair, Inc.
High Performance Micro-D Connectors and Cables
U.S. CAGE Code 06324
Printed in U.S.A.
GLENAIR, INC.
1211 AIR WAY
GLENDALE, CA 91201-2497
818-247-6000
FAX 818-500-9912
www.glenair.com
B-14
E-Mail: sales@glenair.com
Looking for a compiled and configured Mini2440 project
I have a Mini2440 development board. Since the entry threshold of Linux is too high, I need an MDK project configuration file that supports mini2440 development under RT-Thread1.1.0. After referring t...
LuoHG Embedded System
Share the ucos transplantation manual based on LPC1768
[color=#ff00][size=6]Some time ago, I did a project with LPC1768, and I needed to use the UCOS system. I searched the Internet but couldn't find any porting information. I downloaded a DEMO from the o...
openmcu890 Microcontroller MCU
Linear optocoupler isolation voltage problem
The figure below is the voltage isolation circuit of the linear optocoupler HCNR201. R1 and R2 in the figure are feedback resistors. If the resistance values are equal, the voltage changes on both sid...
bigbat Analog electronics
Temperature control using MSP430
[size=4]For MSP430, the following modules cooperate with each other to realize the temperature control module. It will be divided into the following parts for explanation: Clock source part ADC part I...
fish001 Microcontroller MCU
I want someone who knows TCPIP to see where my problem is.
The board is LPC1768, and lwip needs to send data to the computer continuously, so I wrote an infinite loop in the callback function CMD_recv. Every time it sends 231 times, the client can no longer r...
sunflowerfsw ARM Technology
Recalling the struggle process
[i=s]This post was last edited by paulhyde on 2014-9-15 09:37[/i] [font=Verdana] We succeeded, we succeeded. I couldn't help but be excited for a while when I heard that we won the first prize. [/font...
songbo Electronics Design Contest

Technical ResourceMore

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 912  242  1651  2468  2617  19  5  34  50  53 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号