EEWORLDEEWORLDEEWORLD

Part Number

Search

177-740-2-67GS6K1-18MVN

Description
Cable Assembly, 26AWG,
CategoryThe connector    Connector bracket   
File Size858KB,5 Pages
ManufacturerGlenair
Websitehttp://www.glenair.com/
Environmental Compliance
Download Datasheet Parametric View All

177-740-2-67GS6K1-18MVN Overview

Cable Assembly, 26AWG,

177-740-2-67GS6K1-18MVN Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
Objectid7005064515
Reach Compliance Codecompliant
Country Of OriginUSA
YTEOL8.75
Other featuresSTANDARD: MIL-DTL-83513, EMI SHIELDED
CertificationMIL
Conductor surface treatmentSILVER
conductor materialCOPPER
ConnectorSide1MICRO-D FEMALE
ConnectorSide2MICRO-D FEMALE
Connector bracket typeCABLE ASSEMBLY
structureSTRANDED
Cross-sectional area0.129 mm2
DIN complianceNO
IEC complianceNO
insulator materialPOLYTETRAFLUOROETHYLENE
length0.467 mm
MIL complianceYES
Number of conductors67
Maximum operating temperature150 °C
Minimum operating temperature-55 °C
Rated current3 A
Rated voltage150 V
resistance0.125 Ω
shieldYES
stay19X38
Wire gauge26 AWG
Wire and Cable NamesFLEXIBLE CORD AND FIXTURE WIRE
B
SHIELDING EFFECTIVENESS (Db)
1.00E+04
1.00E+05
1.00E+06
1.00E+07
1.00E+08
1.00E+09
SHIELDING EFFECTIVENESS (Db)
Micro-D Harness
EMI Performance with Ground Spring
100
90
80
70
60
50
40
30
20
10
0
1.00E+03
MWDM Micro-D
Shielded Cable Assembly
Single-Ended or Double-Ended–These
easy-to-order cable
assemblies eliminate the need for expensive assembly labor. 100%
tested and ready for use.
Now With Twisted Pairs–No
need to create a procurement
specification for Micro-D cables with twisted pairs. Glenair 177-740
cables are furnished with a full complement of white/blue twisted
pair wires.
Integral Shield Termination–The
connector shell has a platform
to accept Band-It shield termination bands. The cable shield braid is
attached directly to the connector.
Save Labor, Reduce Weight and Improve EMI Shielding
with Glenair’s Micro-D Shielded Cable Assemblies
Aerospace electronics systems require higher and higher levels of protection from radiated emissions. Glenair’s
fully shielded Micro-D cable assemblies meet this need. The cable shield is attached directly onto the one-
piece connector shell and secured with a stainless steel
Band-Master™ ATS
clamp. These pre-wired, 100% tested
assemblies meet the requirements of MIL-DTL-83513. An optional ground spring on the pin connector assures low
shell-to-shell resistance. Available with a variety of wire types and shields, Micro-D shielded assemblies can be
ordered in any length, either single-ended or “back-to-back”.
Ground Spring and EMI Shielding Effectiveness
A gold-plated stainless steel ground spring on the pin connector mating
face offers substantial improvement in EMI protection. The graphs
compare identical connectors tested with and without ground springs.
EMI Performance without Ground Spring
100
90
80
70
60
50
40
30
20
10
0
1.00E+03
1.00E+04
1.00E+05
1.00E+06
1.00E+07
1.00E+08
1.00E+09
frequency (Hz)
frequency (Hz)
© 2013 Glenair, Inc.
High Performance Micro-D Connectors and Cables
U.S. CAGE Code 06324
Printed in U.S.A.
GLENAIR, INC.
1211 AIR WAY
GLENDALE, CA 91201-2497
818-247-6000
FAX 818-500-9912
www.glenair.com
B-14
E-Mail: sales@glenair.com
[Zhou Ligong ARM9 imx28 learning day 2]
[i=s] This post was last edited by qq670300923 on 2016-8-9 16:40 [/i] I had planned to go to a training institution for a month of training recently, but it was too expensive, so I didn't sign up. I d...
qq670300923 Linux and Android
About DA voltage output
The user guide gives this formula: Vout = Vref * DAC12_xDAT/4096; DAC12_xDAT uses straight binary data format, so how to calculate it if it is a hexadecimal number? And it seems that the routines prov...
浅影月居 Microcontroller MCU
NRF24L01 Mega16 Program
My NRF24L01 program has been debugged and is very practical!...
rxm24217 RF/Wirelessly
Ask a question about dBFS
The following figure is a picture of a 24-bit ADC. I found some information about dBFS. For a 24-bit ADC, dBFS = 20*log(code / 16777216). The maximum is 0dBFS and the minimum should be -144.49dBFS. Ho...
littleshrimp Analog electronics
Is it possible to apply for a larger buf on the c8051f chip?
I am using C8051F020. The program needs to apply for a buf of more than 10k, but the on-chip ram is only 8k. I want to apply for it in the on-chip flash area. I wonder if it is possible? I have seen s...
tencom Embedded System
TCK (pin 9) low, but should be high. Please check target hardware
TCK (pin 9) low, but should be high. Please check target hardware ??? The emulator reports an error. It worked fine before and now it doesn't work anymore without any changes? Thanks!!!...
starcyh12 NXP MCU

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1212  1414  1517  119  1563  25  29  31  3  32 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号