EEWORLDEEWORLDEEWORLD

Part Number

Search

177-740-5-67CS0J1-18RNN

Description
Cable Assembly, 30AWG,
CategoryThe connector    Connector bracket   
File Size858KB,5 Pages
ManufacturerGlenair
Websitehttp://www.glenair.com/
Download Datasheet Parametric View All

177-740-5-67CS0J1-18RNN Overview

Cable Assembly, 30AWG,

177-740-5-67CS0J1-18RNN Parametric

Parameter NameAttribute value
Objectid7005111992
Reach Compliance Codeunknown
YTEOL8.23
Other featuresSTANDARD: MIL-DTL-83513
CertificationMIL
Conductor surface treatmentSILVER
conductor materialCOPPER
ConnectorSide1MICRO-D MALE
ConnectorSide2MICRO-D FEMALE
Connector bracket typeCABLE ASSEMBLY
structureSTRANDED
Cross-sectional area0.051 mm2
DIN complianceNO
IEC complianceNO
insulator materialCROSSLINKED ETHYLENE-TETRAFLUOROETHYLENE
length0.467 mm
MIL complianceYES
Number of conductors67
Maximum operating temperature150 °C
Minimum operating temperature-55 °C
Rated current3 A
Rated voltage150 V
resistance0.385 Ω
shieldNO
stay7X38
Wire gauge30 AWG
Wire and Cable NamesFLEXIBLE CORD AND FIXTURE WIRE
B
SHIELDING EFFECTIVENESS (Db)
1.00E+04
1.00E+05
1.00E+06
1.00E+07
1.00E+08
1.00E+09
SHIELDING EFFECTIVENESS (Db)
Micro-D Harness
EMI Performance with Ground Spring
100
90
80
70
60
50
40
30
20
10
0
1.00E+03
MWDM Micro-D
Shielded Cable Assembly
Single-Ended or Double-Ended–These
easy-to-order cable
assemblies eliminate the need for expensive assembly labor. 100%
tested and ready for use.
Now With Twisted Pairs–No
need to create a procurement
specification for Micro-D cables with twisted pairs. Glenair 177-740
cables are furnished with a full complement of white/blue twisted
pair wires.
Integral Shield Termination–The
connector shell has a platform
to accept Band-It shield termination bands. The cable shield braid is
attached directly to the connector.
Save Labor, Reduce Weight and Improve EMI Shielding
with Glenair’s Micro-D Shielded Cable Assemblies
Aerospace electronics systems require higher and higher levels of protection from radiated emissions. Glenair’s
fully shielded Micro-D cable assemblies meet this need. The cable shield is attached directly onto the one-
piece connector shell and secured with a stainless steel
Band-Master™ ATS
clamp. These pre-wired, 100% tested
assemblies meet the requirements of MIL-DTL-83513. An optional ground spring on the pin connector assures low
shell-to-shell resistance. Available with a variety of wire types and shields, Micro-D shielded assemblies can be
ordered in any length, either single-ended or “back-to-back”.
Ground Spring and EMI Shielding Effectiveness
A gold-plated stainless steel ground spring on the pin connector mating
face offers substantial improvement in EMI protection. The graphs
compare identical connectors tested with and without ground springs.
EMI Performance without Ground Spring
100
90
80
70
60
50
40
30
20
10
0
1.00E+03
1.00E+04
1.00E+05
1.00E+06
1.00E+07
1.00E+08
1.00E+09
frequency (Hz)
frequency (Hz)
© 2013 Glenair, Inc.
High Performance Micro-D Connectors and Cables
U.S. CAGE Code 06324
Printed in U.S.A.
GLENAIR, INC.
1211 AIR WAY
GLENDALE, CA 91201-2497
818-247-6000
FAX 818-500-9912
www.glenair.com
B-14
E-Mail: sales@glenair.com
S3C2440 SPI receiving problem
I have a question about S3C2440 SPI receiving. The program code is as follows. I can capture the correct waveforms of MISO and MOSI through an oscilloscope, indicating that the data transmission and r...
thingwind Embedded System
There is no signal at all when using the ceramic antenna on the cc2541. Can anyone help me see if that is wrong?
I tried to draw the board myself. The ceramic antenna I used was RFANT3216120A5T, and I drew it according to the data sheet. First, the balun outputted a 50Ω impedance, and then the antenna. But the r...
osiris00 Wireless Connectivity
Ask about the application of Mitsubishi FR-E740 on conveyor belt
Hi everyone, I would like to ask you something:I have a Mitsubishi FR E740 inverter, which is used on a conveyor belt. A proximity switch is used to control the start and stop of the motor. The proxim...
eeleader-mcu Industrial Control Electronics
MCU system EMC test
EMC testing includes two aspects: testing the electromagnetic disturbance intensity sent to the outside world and testing its sensitivity under the electromagnetic environment conditions with specifie...
qwqwqw2088 Power technology
[Book Collection] Guide to solving problems in analog electronic circuits
[b]Contents: [/b] Part I Analog Electronic Circuits Chapter 1 Semiconductor Components Chapter 2 Amplifier Basics Chapter 3 Feedback in Amplifiers Chapter 4 Frequency Characteristics of Amplifiers Cha...
wzt Analog electronics
How to migrate eboot under 2440 ce5.0 to ce6.0?
01:0000000127:ERRORE] fulllibc.lib(armsecgs.obj) : error LNK2001: unresolved external symbol __security_cookie BUILD: [01:0000000128:ERRORE] smflash_lib.lib(fmd.obj) : error LNK2001: unresolved extern...
hub128 Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2597  1253  2168  810  3  53  26  44  17  1 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号