POR Specifications....................................................................................................................................................81
AS Configuration Timing............................................................................................................................................86
DCLK Frequency Specification in the AS Configuration Scheme....................................................................................... 87
Minimum Configuration Time Estimation......................................................................................................................91
Remote System Upgrades......................................................................................................................................... 93
User Watchdog Internal Circuitry Timing Specifications..................................................................................................93
Document Revision History for the Intel Arria 10 Device Datasheet.......................................................................................... 99
Intel
®
Arria
®
10 Device Datasheet
2
Send Feedback
A10-DATASHEET | 2019.06.24
Send Feedback
Intel
®
Arria
®
10 Device Datasheet
This datasheet describes the electrical characteristics, switching characteristics, configuration specifications, and I/O timing
for Intel
®
Arria
®
10 devices.
Intel Arria 10 devices are offered in extended and industrial grades. Extended devices are offered in –E1 (fastest), –E2, and –
E3 speed grades. Industrial grade devices are offered in the –I1, –I2, and –I3 speed grades.
The suffix after the speed grade denotes the power options offered in Intel Arria 10 devices.
•
•
•
•
L—enables the device to operate at low static power while maintaining excellent performance.
S—standard power specification.
V—enables the device to run at lower than default V
CC
, reducing static and dynamic power while retaining equivalent
performance.
H—small device with high performance at the fastest speed grade (–1).
Related Information
Intel Arria 10 Device Overview
Provides more information about the densities and packages of devices in the Intel Arria 10 family.
Electrical Characteristics
The following sections describe the operating conditions and power consumption of Intel Arria 10 devices.
Operating Conditions
Intel Arria 10 devices are rated according to a set of defined parameters. To maintain the highest possible performance and
reliability of the Intel Arria 10 devices, you must consider the operating requirements described in this section.
Intel Corporation. All rights reserved. Agilex, Altera, Arria, Cyclone, Enpirion, Intel, the Intel logo, MAX, Nios, Quartus and Stratix words and logos are trademarks
of Intel Corporation or its subsidiaries in the U.S. and/or other countries. Intel warrants performance of its FPGA and semiconductor products to current
specifications in accordance with Intel's standard warranty, but reserves the right to make changes to any products and services at any time without notice. Intel
assumes no responsibility or liability arising out of the application or use of any information, product, or service described herein except as expressly agreed to in
writing by Intel. Intel customers are advised to obtain the latest version of device specifications before relying on any published information and before placing
orders for products or services.
*Other names and brands may be claimed as the property of others.
ISO
9001:2015
Registered
Intel
®
Arria
®
10 Device Datasheet
A10-DATASHEET | 2019.06.24
Absolute Maximum Ratings
This section defines the maximum operating conditions for Intel Arria 10 devices. The values are based on experiments
conducted with the devices and theoretical modeling of breakdown and damage mechanisms. The functional operation of the
device is not implied for these conditions.
Caution:
Table 1.
Conditions outside the range listed in the following table may cause permanent damage to the device. Additionally, device
operation at the absolute maximum ratings for extended periods of time may have adverse effects on the device.
Absolute Maximum Ratings for Intel Arria 10 Devices
Symbol
V
CC
V
CCP
V
CCERAM
V
CCPT
V
CCBAT
V
CCPGM
V
CCIO
Core voltage power supply
Periphery circuitry and transceiver fabric interface power supply
Embedded memory power supply
Power supply for programmable power technology and I/O pre-driver
Battery back-up power supply for design security volatile key register
Configuration pins power supply
I/O buffers power supply
Description
Condition
—
—
—
—
—
(1)
Minimum
–0.50
–0.50
–0.50
–0.50
–0.50
–0.50
–0.50
–0.50
–0.50
–0.50
–0.50
–0.50
–0.50
–0.50
–0.50
–0.50
Maximum
1.21
1.21
1.36
2.46
2.46
2.46
4.10
2.46
2.46
1.34
1.34
2.46
1.27
4.10
2.46
2.46
Unit
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
continued...
3 V I/O
LVDS I/O
V
CCA_PLL
V
CCT_GXB
V
CCR_GXB
V
CCH_GXB
V
CCL_HPS
V
CCIO_HPS
Phase-locked loop (PLL) analog power supply
Transmitter power supply
Receiver power supply
Transceiver output buffer power supply
HPS core voltage and periphery circuitry power supply
HPS I/O buffers power supply
—
—
—
—
—
3 V I/O
LVDS I/O
V
CCIOREF_HPS
HPS I/O pre-driver power supply
—
(1)
The LVDS I/O values are applicable to all dedicated and dual-function configuration I/Os.
Intel
®
Arria
®
10 Device Datasheet
4
Send Feedback
Intel
®
Arria
®
10 Device Datasheet
A10-DATASHEET | 2019.06.24
Symbol
V
CCPLL_HPS
I
OUT
T
J
T
STG
HPS PLL power supply
DC output current per pin
Description
Condition
—
—
—
—
Minimum
–0.50
–25
(2)(3)(4)(5)
(6)
Maximum
2.46
25
125
150
Unit
V
mA
°C
°C
Operating junction temperature
Storage temperature (no bias)
–55
–65
Related Information
•
•
AN 692: Power Sequencing Considerations for Intel Cyclone 10 GX, Intel Arria 10, and Intel Stratix 10 Devices
Provides the power sequencing requirements for Intel Arria 10 devices.
Power-Up and Power-Down Sequences, Power Management in Intel Arria 10 Devices chapter
Provides the power sequencing requirements for Intel Arria 10 devices.
Maximum Allowed Overshoot and Undershoot Voltage
During transitions, input signals may overshoot to the voltage listed in the following table and undershoot to –2.0 V for input
currents less than 100 mA and periods shorter than 20 ns.
The maximum allowed overshoot duration is specified as a percentage of high time over the lifetime of the device. A DC signal
is equivalent to 100% duty cycle.
For example, a signal that overshoots to 2.70 V for LVDS I/O can only be at 2.70 V for ~4% over the lifetime of the device.
(2)
The maximum current allowed through any LVDS I/O bank pin when the device is not turned on or during power-up/power-down
conditions is 10 mA.
Total current per LVDS I/O bank must not exceed 100 mA.
Voltage level must not exceed 1.89 V.
Applies to all I/O standards and settings supported by LVDS I/O banks, including single-ended and differential I/Os.
Applies only to LVDS I/O banks. 3 V I/O banks are not covered under this specification and must be implemented as per the power
sequencing requirement. For more details, refer to
AN 692: Power Sequencing Considerations for Intel Cyclone
®
10 GX, Intel Arria
10, and Intel Stratix
®
10 Devices
and
Power Management in Intel Arria 10 Devices chapter.
[i=s] This post was last edited by Brother Meng Yi on 2015-7-20 13:06 [/i] [align=left][font=宋体]Foreword: The shift register IP core seems to have been inconspicuous, and many beginners don’t know abo...
0000]//添加的DEBUG[/color] Microsoft Windows CE Bootloader Common Library Version 1.4 Built Mar 26 2009 22:59:02 Microsoft Windows CE Bootloader for the Samsung SMDK2440 Version 2.4 Built Mar 31 2009 run...
[i=s]This post was last edited by niuyuzhe on 2015-5-16 00:11[/i] I don't know much about technology, but I have a product idea. The requirements are: A set of equipment, divided into equipment A, B a...
I am still a student, a super rookie. I just came into contact with this development board because of my teacher's project. Now I have this problem: I am making a WIN CE6.0 simulator in VS2005. I down...
Hello everyone: I have encountered the following problem: Hardware; TI High vol Motor kit+pfc. The program simulation runs OK. Power off, unplug the emulator USB cable, power on, but the program does ...
Hardware designers have begun to adopt FPGA technology in high-performance DSP designs because it can provide 10-100 times faster computing than PC-based or microcontroller-based solutions. Previou...[Details]
A single-chip microcomputer is also called a single-chip microcontroller. It is not a chip that completes a certain logical function, but a computer system integrated into one chip. In general, a c...[Details]
introduction
my country has a vast territory and a large population. The scale of housing construction is huge, and the amount of residential construction is large and wide. It is still on t...[Details]
introduction
In the discharge process of tokamak plasma physics, the study of rupture and sawtooth is of great significance. Rupture and sawtooth exist in most tokamaks. Rupture is a notew...[Details]
System design is a complex process. It is not enough to just use ICs. There are many details to consider. This article uses a high-fidelity music playback system as an example to introduce how to s...[Details]
1. Principle of displacement angle sensor
The angle sensor is used to detect angles. It has a hole in its body that fits the LEGO axle. When connected to the RCX, the angle sensor counts once ...[Details]
1 Introduction
Intelligent control instruments are one of the most commonly used controllers in industrial control. They are mainly aimed at a specific parameter (such as pressure, tempera...[Details]
Printed circuit boards ( PCBs
)
are used in most electrical products
. If a PCB has low
insulation resistance
(IR), the performance of the circuits on the PCB will be greatly reduced...[Details]
hint:
The number of speakers and their spacing limit the sound field of a portable stereo system.
Spatial audio attempts to artificially recreate the experience of listening to sounds i...[Details]
Corelink Semiconductor has launched the CL1100-based 5-7W E27 LED lighting driver system solution DB2. This driver module meets the requirements of small size (L×W×H=5.1cm×2.1cm×1.8cm), low standby...[Details]
With the widespread application of new services and technologies in the communications industry, the scale and capacity of operators' network construction are getting larger and larger, and the ris...[Details]
1 Basic Features
In computer control systems and various intelligent instruments and meters composed of single-chip microcomputers (or microprocessors), various external analog signals must be ...[Details]
With the rapid development of cities and the improvement of citizens' living standards, the number of various vehicles in cities is growing, and the demand for parking spaces in major commercial an...[Details]
In the "digital pressure measurement" experimental device of applied physics, the subject technical knowledge of analog circuits, digital circuits, sensors and single-chip microcomputers is used. In o...[Details]
Distributed Wireless Communication System (DWCS) uses distributed antennas, distributed processing control, joint signal processing and other technologies to improve the system's spectrum efficie...[Details]
FPGA/CPLD
京公网安备 11010802033920号
EEWORLD
