POR Specifications....................................................................................................................................................81
AS Configuration Timing............................................................................................................................................86
DCLK Frequency Specification in the AS Configuration Scheme....................................................................................... 87
Minimum Configuration Time Estimation......................................................................................................................91
Remote System Upgrades......................................................................................................................................... 93
User Watchdog Internal Circuitry Timing Specifications..................................................................................................93
Document Revision History for the Intel Arria 10 Device Datasheet.......................................................................................... 99
Intel
®
Arria
®
10 Device Datasheet
2
Send Feedback
A10-DATASHEET | 2019.06.24
Send Feedback
Intel
®
Arria
®
10 Device Datasheet
This datasheet describes the electrical characteristics, switching characteristics, configuration specifications, and I/O timing
for Intel
®
Arria
®
10 devices.
Intel Arria 10 devices are offered in extended and industrial grades. Extended devices are offered in –E1 (fastest), –E2, and –
E3 speed grades. Industrial grade devices are offered in the –I1, –I2, and –I3 speed grades.
The suffix after the speed grade denotes the power options offered in Intel Arria 10 devices.
•
•
•
•
L—enables the device to operate at low static power while maintaining excellent performance.
S—standard power specification.
V—enables the device to run at lower than default V
CC
, reducing static and dynamic power while retaining equivalent
performance.
H—small device with high performance at the fastest speed grade (–1).
Related Information
Intel Arria 10 Device Overview
Provides more information about the densities and packages of devices in the Intel Arria 10 family.
Electrical Characteristics
The following sections describe the operating conditions and power consumption of Intel Arria 10 devices.
Operating Conditions
Intel Arria 10 devices are rated according to a set of defined parameters. To maintain the highest possible performance and
reliability of the Intel Arria 10 devices, you must consider the operating requirements described in this section.
Intel Corporation. All rights reserved. Agilex, Altera, Arria, Cyclone, Enpirion, Intel, the Intel logo, MAX, Nios, Quartus and Stratix words and logos are trademarks
of Intel Corporation or its subsidiaries in the U.S. and/or other countries. Intel warrants performance of its FPGA and semiconductor products to current
specifications in accordance with Intel's standard warranty, but reserves the right to make changes to any products and services at any time without notice. Intel
assumes no responsibility or liability arising out of the application or use of any information, product, or service described herein except as expressly agreed to in
writing by Intel. Intel customers are advised to obtain the latest version of device specifications before relying on any published information and before placing
orders for products or services.
*Other names and brands may be claimed as the property of others.
ISO
9001:2015
Registered
Intel
®
Arria
®
10 Device Datasheet
A10-DATASHEET | 2019.06.24
Absolute Maximum Ratings
This section defines the maximum operating conditions for Intel Arria 10 devices. The values are based on experiments
conducted with the devices and theoretical modeling of breakdown and damage mechanisms. The functional operation of the
device is not implied for these conditions.
Caution:
Table 1.
Conditions outside the range listed in the following table may cause permanent damage to the device. Additionally, device
operation at the absolute maximum ratings for extended periods of time may have adverse effects on the device.
Absolute Maximum Ratings for Intel Arria 10 Devices
Symbol
V
CC
V
CCP
V
CCERAM
V
CCPT
V
CCBAT
V
CCPGM
V
CCIO
Core voltage power supply
Periphery circuitry and transceiver fabric interface power supply
Embedded memory power supply
Power supply for programmable power technology and I/O pre-driver
Battery back-up power supply for design security volatile key register
Configuration pins power supply
I/O buffers power supply
Description
Condition
—
—
—
—
—
(1)
Minimum
–0.50
–0.50
–0.50
–0.50
–0.50
–0.50
–0.50
–0.50
–0.50
–0.50
–0.50
–0.50
–0.50
–0.50
–0.50
–0.50
Maximum
1.21
1.21
1.36
2.46
2.46
2.46
4.10
2.46
2.46
1.34
1.34
2.46
1.27
4.10
2.46
2.46
Unit
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
continued...
3 V I/O
LVDS I/O
V
CCA_PLL
V
CCT_GXB
V
CCR_GXB
V
CCH_GXB
V
CCL_HPS
V
CCIO_HPS
Phase-locked loop (PLL) analog power supply
Transmitter power supply
Receiver power supply
Transceiver output buffer power supply
HPS core voltage and periphery circuitry power supply
HPS I/O buffers power supply
—
—
—
—
—
3 V I/O
LVDS I/O
V
CCIOREF_HPS
HPS I/O pre-driver power supply
—
(1)
The LVDS I/O values are applicable to all dedicated and dual-function configuration I/Os.
Intel
®
Arria
®
10 Device Datasheet
4
Send Feedback
Intel
®
Arria
®
10 Device Datasheet
A10-DATASHEET | 2019.06.24
Symbol
V
CCPLL_HPS
I
OUT
T
J
T
STG
HPS PLL power supply
DC output current per pin
Description
Condition
—
—
—
—
Minimum
–0.50
–25
(2)(3)(4)(5)
(6)
Maximum
2.46
25
125
150
Unit
V
mA
°C
°C
Operating junction temperature
Storage temperature (no bias)
–55
–65
Related Information
•
•
AN 692: Power Sequencing Considerations for Intel Cyclone 10 GX, Intel Arria 10, and Intel Stratix 10 Devices
Provides the power sequencing requirements for Intel Arria 10 devices.
Power-Up and Power-Down Sequences, Power Management in Intel Arria 10 Devices chapter
Provides the power sequencing requirements for Intel Arria 10 devices.
Maximum Allowed Overshoot and Undershoot Voltage
During transitions, input signals may overshoot to the voltage listed in the following table and undershoot to –2.0 V for input
currents less than 100 mA and periods shorter than 20 ns.
The maximum allowed overshoot duration is specified as a percentage of high time over the lifetime of the device. A DC signal
is equivalent to 100% duty cycle.
For example, a signal that overshoots to 2.70 V for LVDS I/O can only be at 2.70 V for ~4% over the lifetime of the device.
(2)
The maximum current allowed through any LVDS I/O bank pin when the device is not turned on or during power-up/power-down
conditions is 10 mA.
Total current per LVDS I/O bank must not exceed 100 mA.
Voltage level must not exceed 1.89 V.
Applies to all I/O standards and settings supported by LVDS I/O banks, including single-ended and differential I/Os.
Applies only to LVDS I/O banks. 3 V I/O banks are not covered under this specification and must be implemented as per the power
sequencing requirement. For more details, refer to
AN 692: Power Sequencing Considerations for Intel Cyclone
®
10 GX, Intel Arria
10, and Intel Stratix
®
10 Devices
and
Power Management in Intel Arria 10 Devices chapter.
I installed a new system on my computer today, but after turning it on I found that the USB blaster didn't work. I was frustrated and plugged in the download cable, but the following prompt appeared [...
I have recently encountered a difficult problem. I am designing a DC motor PWM speed control system. I use a 51 single-chip microcomputer, the main circuit is an H bridge, the keyboard is 4*4, the dis...
As the title says, I want to make a humidity measurement system, but I can't use a temperature and humidity integrated chip, so I would like to ask you for some advice on what sensor I should use. How...
What kind of professional knowledge is DVM digital voltmeter? My friend asked me to help him write a paper on this subject. Is there any book on this subject that you can recommend? Please tell me abo...
Can JTAG be connected in series via SWD? 6 On one side is STM32F030, which only has SWD interface, and on the other side is STM32F107, which has JTAG and SWD interfaces. How should it be designed? The...
This program is written to simulate the serial port hardware mechanism. When used, a timed interrupt can be set with a time interval of 1/4 baud rate. The receiving function is called once for ea...[Details]
1. Introduction
Since the 1980s, with the continuous development of automotive electronic technology, there are more and more electronic control units in automobiles, such as electronic fuel i...[Details]
In this article, the high-performance DSP developed by TI can be used as an effective confidentiality method if it is applied to PC encryption cards.
As an effective network security solution,...[Details]
DSP (digital signal processor) is used more and more frequently in today's engineering applications. There are three main reasons for this: first, it has powerful computing power and is capable of ...[Details]
Contact resistance
is the resistance to current flow through a closed pair of contacts. This type of measurement is performed on devices such as connectors,
relays
, and switches. The...[Details]
1. Background:
The instrument system parameter detection and control of the chemical production workshop of Tangshan Coal Gas Coking Plant are all analog instruments, some of which are eve...[Details]
1 Introduction to HART Protocol
HART (Highway Addressable Remote Transducer), an open communication protocol for addressable remote sensor high-speed channels, was launched by Rosemen in the U...[Details]
At very low temperatures, certain metals and alloys lose their resistance to electric
current
and become
superconductors
. Two parameters that are often measured are the transition ...[Details]
1. Overview
At present, an information revolution is in the ascendant around the world, led by microelectronics, computers and communication technologies, and centered on information technolog...[Details]
1 Introduction
With the improvement of people's quality of life, lamps are no longer just basic indoor lighting tools, but also a kind of practical art for architectural decoration. When ther...[Details]
0 Introduction
There are many types of sensors, and the working principles, measurement targets and measurement environments of different types of sensors vary greatly. The corresponding detection s...[Details]
Our flight had just begun to descend when a gentleman sitting next to me turned to talk to me about engineering—he had seen me reading an engineering journal. The gentleman next to me said that he ...[Details]
Overview
By transmitting ultrasonic energy into the human body and receiving and processing the returning reflected signals, phased array ultrasound systems can generate images of organs and s...[Details]
The demand for improved healthcare environments is endless, so medical imaging equipment with higher resolution is needed to better observe the human body. High resolution brings problems with sign...[Details]
The emergence and development of street lamps are inseparable from the prosperity and progress of cities, which makes street lamps useful. Conversely, street lamps also make the night of the city n...[Details]
FPGA/CPLD
京公网安备 11010802033920号
EEWORLD
