POR Specifications....................................................................................................................................................81
AS Configuration Timing............................................................................................................................................86
DCLK Frequency Specification in the AS Configuration Scheme....................................................................................... 87
Minimum Configuration Time Estimation......................................................................................................................91
Remote System Upgrades......................................................................................................................................... 93
User Watchdog Internal Circuitry Timing Specifications..................................................................................................93
Document Revision History for the Intel Arria 10 Device Datasheet.......................................................................................... 99
Intel
®
Arria
®
10 Device Datasheet
2
Send Feedback
A10-DATASHEET | 2019.06.24
Send Feedback
Intel
®
Arria
®
10 Device Datasheet
This datasheet describes the electrical characteristics, switching characteristics, configuration specifications, and I/O timing
for Intel
®
Arria
®
10 devices.
Intel Arria 10 devices are offered in extended and industrial grades. Extended devices are offered in –E1 (fastest), –E2, and –
E3 speed grades. Industrial grade devices are offered in the –I1, –I2, and –I3 speed grades.
The suffix after the speed grade denotes the power options offered in Intel Arria 10 devices.
•
•
•
•
L—enables the device to operate at low static power while maintaining excellent performance.
S—standard power specification.
V—enables the device to run at lower than default V
CC
, reducing static and dynamic power while retaining equivalent
performance.
H—small device with high performance at the fastest speed grade (–1).
Related Information
Intel Arria 10 Device Overview
Provides more information about the densities and packages of devices in the Intel Arria 10 family.
Electrical Characteristics
The following sections describe the operating conditions and power consumption of Intel Arria 10 devices.
Operating Conditions
Intel Arria 10 devices are rated according to a set of defined parameters. To maintain the highest possible performance and
reliability of the Intel Arria 10 devices, you must consider the operating requirements described in this section.
Intel Corporation. All rights reserved. Agilex, Altera, Arria, Cyclone, Enpirion, Intel, the Intel logo, MAX, Nios, Quartus and Stratix words and logos are trademarks
of Intel Corporation or its subsidiaries in the U.S. and/or other countries. Intel warrants performance of its FPGA and semiconductor products to current
specifications in accordance with Intel's standard warranty, but reserves the right to make changes to any products and services at any time without notice. Intel
assumes no responsibility or liability arising out of the application or use of any information, product, or service described herein except as expressly agreed to in
writing by Intel. Intel customers are advised to obtain the latest version of device specifications before relying on any published information and before placing
orders for products or services.
*Other names and brands may be claimed as the property of others.
ISO
9001:2015
Registered
Intel
®
Arria
®
10 Device Datasheet
A10-DATASHEET | 2019.06.24
Absolute Maximum Ratings
This section defines the maximum operating conditions for Intel Arria 10 devices. The values are based on experiments
conducted with the devices and theoretical modeling of breakdown and damage mechanisms. The functional operation of the
device is not implied for these conditions.
Caution:
Table 1.
Conditions outside the range listed in the following table may cause permanent damage to the device. Additionally, device
operation at the absolute maximum ratings for extended periods of time may have adverse effects on the device.
Absolute Maximum Ratings for Intel Arria 10 Devices
Symbol
V
CC
V
CCP
V
CCERAM
V
CCPT
V
CCBAT
V
CCPGM
V
CCIO
Core voltage power supply
Periphery circuitry and transceiver fabric interface power supply
Embedded memory power supply
Power supply for programmable power technology and I/O pre-driver
Battery back-up power supply for design security volatile key register
Configuration pins power supply
I/O buffers power supply
Description
Condition
—
—
—
—
—
(1)
Minimum
–0.50
–0.50
–0.50
–0.50
–0.50
–0.50
–0.50
–0.50
–0.50
–0.50
–0.50
–0.50
–0.50
–0.50
–0.50
–0.50
Maximum
1.21
1.21
1.36
2.46
2.46
2.46
4.10
2.46
2.46
1.34
1.34
2.46
1.27
4.10
2.46
2.46
Unit
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
V
continued...
3 V I/O
LVDS I/O
V
CCA_PLL
V
CCT_GXB
V
CCR_GXB
V
CCH_GXB
V
CCL_HPS
V
CCIO_HPS
Phase-locked loop (PLL) analog power supply
Transmitter power supply
Receiver power supply
Transceiver output buffer power supply
HPS core voltage and periphery circuitry power supply
HPS I/O buffers power supply
—
—
—
—
—
3 V I/O
LVDS I/O
V
CCIOREF_HPS
HPS I/O pre-driver power supply
—
(1)
The LVDS I/O values are applicable to all dedicated and dual-function configuration I/Os.
Intel
®
Arria
®
10 Device Datasheet
4
Send Feedback
Intel
®
Arria
®
10 Device Datasheet
A10-DATASHEET | 2019.06.24
Symbol
V
CCPLL_HPS
I
OUT
T
J
T
STG
HPS PLL power supply
DC output current per pin
Description
Condition
—
—
—
—
Minimum
–0.50
–25
(2)(3)(4)(5)
(6)
Maximum
2.46
25
125
150
Unit
V
mA
°C
°C
Operating junction temperature
Storage temperature (no bias)
–55
–65
Related Information
•
•
AN 692: Power Sequencing Considerations for Intel Cyclone 10 GX, Intel Arria 10, and Intel Stratix 10 Devices
Provides the power sequencing requirements for Intel Arria 10 devices.
Power-Up and Power-Down Sequences, Power Management in Intel Arria 10 Devices chapter
Provides the power sequencing requirements for Intel Arria 10 devices.
Maximum Allowed Overshoot and Undershoot Voltage
During transitions, input signals may overshoot to the voltage listed in the following table and undershoot to –2.0 V for input
currents less than 100 mA and periods shorter than 20 ns.
The maximum allowed overshoot duration is specified as a percentage of high time over the lifetime of the device. A DC signal
is equivalent to 100% duty cycle.
For example, a signal that overshoots to 2.70 V for LVDS I/O can only be at 2.70 V for ~4% over the lifetime of the device.
(2)
The maximum current allowed through any LVDS I/O bank pin when the device is not turned on or during power-up/power-down
conditions is 10 mA.
Total current per LVDS I/O bank must not exceed 100 mA.
Voltage level must not exceed 1.89 V.
Applies to all I/O standards and settings supported by LVDS I/O banks, including single-ended and differential I/Os.
Applies only to LVDS I/O banks. 3 V I/O banks are not covered under this specification and must be implemented as per the power
sequencing requirement. For more details, refer to
AN 692: Power Sequencing Considerations for Intel Cyclone
®
10 GX, Intel Arria
10, and Intel Stratix
®
10 Devices
and
Power Management in Intel Arria 10 Devices chapter.
Please send your resume to [email=China.Recruiting@lsi.com]China.Recruiting@lsi.com[/email][b][font=Arial][size=10pt]DESCRIPTION OF DUTIES IN ADDITION TO THOSE IN JOB DESCRIPTION:[/size][/font][/b]
[a...
The adapter output voltage is 5V, but different modules in the circuit require input voltages of 1.8V, 2.4V, 3.0V, and 4.5V. What should I do? ? ? ? ?...
Today I read the chapter on interrupts, but I still don't understand some parts of SWI. I would like to ask all the experts for help, thank you! The problem is in the place where the interrupt is load...
[i=s]This post was last edited by Changjianze1 on 2015-5-20 23:56[/i] [align=left][size=5][b]1. Introduction[/b][/size][/align][align=left][size=3]The previous few articles simply implemented the read...
[i=s]This post was last edited by paulhyde on 2014-9-15 03:38[/i][table=98%][tr][td]Author: Yang Jun and Jin Xinmin, Institute of New Energy, School of Electrical Engineering, Beijing Jiaotong Univers...
Assume that data is read from 8-bit AD (if it is a higher-bit AD, the data type can be defined as int), the subroutine is get_ad();
1. Limited secondary filtering
/* A value can be adjust...[Details]
Floating-point digital signal processing has become a constant requirement for precision technology, often in applications requiring high accuracy in areas such as aviation, industrial machinery, a...[Details]
1 Introduction
Solar street lights are mainly composed of four parts: solar photovoltaic cell components, batteries, charge and discharge controllers, and lighting fixtures. The bo...[Details]
1. What is temperature?
Heat is a type of molecular motion. The hotter an object is, the faster its molecules move. Absolute zero is defined as the temperature at which all molecular motion ...[Details]
1 Introduction
Building Automation System (BAS) is a distributed monitoring system (DCS) designed according to distributed information and control theory. It is the result of the mutual de...[Details]
Since the No. 4 blast furnace of Handan Iron and Steel was put into operation in 1993, its external equipment has been seriously aged, and the original PLC control system TDC3000 of the hot blast furn...[Details]
1 Introduction
With the development of control, computer, communication, network technology, etc., a new control technology, namely fieldbus, has emerged in the field of industrial control...[Details]
1 Introduction
In recent years, there have been many major advances in the production technology and processes of automotive headlights, which have greatly improved the performance of automoti...[Details]
Experimental tasks
A DS18B20 is used to form a temperature measurement system. The temperature measurement accuracy reaches 0.1 degrees. The temperature range is between -20 degrees and +50 de...[Details]
Overview
In spectral measurement, photomultiplier tubes (PMT) and charge-coupled devices (CCD) are often used as photoelectric converters. PMT is used in slow-changing, high-precision spectral...[Details]
Different initialization between C8051F and 80C51 series microcontrollers
In the past 30 years, major electronic component manufacturers in the world have launched their own unique single-chip...[Details]
Continuity test
A variety of devices need to be checked for continuity, including cable assemblies, printed circuit boards, and connectors to ensure that these components have the expected contin...[Details]
In 2012, more than half of the cars in the European, Japanese and American car markets will be equipped with color displays, navigation systems, satellite communications and other in-vehicle infota...[Details]
At present, the traffic congestion in cities is quite serious. According to relevant news reports: In China, the traffic congestion has expanded from megacities such as Beijing, Shanghai, and Guangzho...[Details]
System Overview
The system consists of a signal preprocessing circuit, a single-chip computer AT89C2051, a systematic LED display module, a serial port data storage circuit and system software...[Details]
Recruitment
京公网安备 11010802033920号
EEWORLD
