FPDR3E1227D02XX datasheet, PDF

Datasheet> All Categories > Mechanical and electronic products> switch> FPDR3E1227D02XX

FPDR3E1227D02XX: DescriptionSpecial Switch,; CategoryMechanical and electronic products switch; File Size251KB，5 Pages; ManufacturerAPEM; Environmental Compliance

Download Datasheet Parametric View All

FPDR3E1227D02XX Overview

Special Switch,

FPDR3E1227D02XX Parametric

Parameter Name	Attribute value
Is it Rohs certified?	conform to
Objectid	145007522594
Reach Compliance Code	unknown
ECCN code	EAR99

Preview

Download Datasheet

View All

New!

Fully illuminated pushbutton switches - bushing Ø 30 mm - momentary or latching

Distinctive features and specifications

4.50

(.177)

Ø26.50

(1.043DIA)

FP series

00 )

4. IA

Ø3 39D

Full actuator or symbol illumination

26.50

(1.043)

Suited for integrated designs

Large but lightweight

Pad printed or laser etched symbols

Snap-in and threaded bushing models

Pad printing

Laser

0.50

(.020)

6.30

(.248)

2.80

(.110)

Ø29.80

(1.173)

Non-illuminated

Ø26.50

(1.043DIA)

00 )

4. IA

Ø3 39D

26.50

(1.043)

Illuminated

4.50

(.177)

6.30

(.248)

ELECTRICAL SPECIFICATIONS

0.50

(.020)

MATERIALS

Ø30.00x1.50 SI

2.80

(.110)

• Max. current/voltage rating with resistive load :

- silver contacts (code 2) : 4A 12VDC

- gold plated contacts (code 4) : 200mA 12VDC

• Initial contact resistance : 50 mΩ max.

• Insulation resistance : 1 GΩ min. at 500VDC

• Dielectric strength : 1.000 Vrms 50 Hz min.

• Electrical life at full load :

- Momentary models : 1 million cycles (gold plated contacts)

400.000 cycles (silver contacts)

- Latching models : 200.000 cycles

GENERAL SPECIFICATIONS

(1.181DIAx1.50 IS)

• Case : PA46

• Actuator : PA12, gloss finish

• Bushing/ bezel : ABS, gloss finish

• Contacts :

Silver (code 2)

or silver, gold plated (code 4)

WIRING DIAGRAM

POLE 2

LED

• Panel thickness :

- Snap-in version : 1,5 (.059) to 2 mm (.078) with panel gasket

2 (.078) to 2,5 mm (.885) without panel gasket

- Threaded bushing version : 1(.039) to 9 mm (.354) max.

• Total travel : 2,8 mm

± 0,5 mm

• Typical operating force : 8N

± 2N

• Low level or mechanical life :

- Momentary models : 1 million cycles

- Latching models : 200.000 cycles

• Torque : 2 Nm max. applied to nut

• Operating temperature : -40°C to +75°C

LED

POLE 1

The company reserves the right to change specifications without notice.

B2-150

www.apem.com

APEM

Recommended Resources

How should the inductor of the switching power supply be placed correctly in PCB design?

Low output impedance operational amplifier circuit

A low-voltage circuit breaker voltage loss delay circuit

Alarm clock equipped with automatic light-on function circuit

Charging circuit diagram using NS-8910 module

6.5kHzLC frequency selective encoder

[Micropython]TPYBoard v10x VS183B infrared remote control development board: [align=center][size=15px][b]This article is just a simple infrared remote control TPYBoard v102 development board data. There are many expansions that can be done. See the attachment for the VS1838 fi...; loktar MicroPython Open Source section

Crystal cleaning problem: [i=s] This post was last edited by jameswangsynnex on 2015-3-3 19:57 [/i] Can the crystal oscillator be cleaned? What cleaning liquid can be used without damaging the crystal oscillator?...; naok654321 Mobile and portable

Distributed temperature control: Can anyone provide some information about distributed temperature control based on MS-51? Thank you! ! ! ! ! Urgent! Urgent! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! !...; zj63613465 MCU

Analysis of the whole process of IAR microcontroller programming software from project establishment to program burning: Microcontroller programming software has many applications in actual projects. Each microcontroller programming software and even different versions of microcontroller programming software have their ...; fish001 Microcontroller MCU

What are your shortcomings in the workplace?: Most people in this world are not immune to this, that is, they are often clear about their strengths and advantages, and even consciously or unconsciously exaggerate them, always thinking that they a...; ESD技术咨询 Talking about work

Look here----->Open source CNC engraving machine control system based on STM32: It took half a year, from transplantation to secondary development, and finally it was basically formed, supporting offline, online, parameter setting and other operations. Let's watch the video: The ...; greatxiaoguzi stm32/stm8

Shortcut: A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 AA AB AC AD AE AF AG AH AI AJ AK AL AM AN AO AP AQ AR AS AT AU AV AW AX AY AZ B0 B1 B2 B3 B4 B5 B6 B7 B8 B9 BA BB BC BD BE BF BG BH BI BJ BK BL BM BN BO BP BQ BR BS BT BU BV BW BX BY BZ C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 CA CB CC CD CE CF CG CH CI CJ CK CL CM CN CO CP CQ CR CS CT CU CV CW CX CY CZ D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 DA DB DC DD DE DF DG DH DI DJ DK DL DM DN DO DP DQ DR DS DT DU DV DW DX DZ

Popular Components