5.0 mm x 3.2 mm Package Pinout ............................................................................................................................................... 1
Ordering Information .................................................................................................................................................................... 2
Device Configurations and Pin-outs ............................................................................................................................................. 9
Pin-out Top Views................................................................................................................................................................. 9
Test Circuit Diagrams for LVCMOS and Clipped Sinewave Outputs ......................................................................................... 10
Frequency Stability ............................................................................................................................................................. 16
Output Frequency and Format............................................................................................................................................ 16
Output Frequency Tuning ................................................................................................................................................... 16
Pin 1 Configuration (OE, VC, or NC) .................................................................................................................................. 17
Control Voltage Bandwidth ................................................................................................................................................. 20
Pull Range and Average Pull Range .................................................................................................................................. 22
Output Frequency ............................................................................................................................................................... 23
2
I C Control Registers .......................................................................................................................................................... 25
Serial Interface Configuration Description .......................................................................................................................... 28
Serial Signal Format ........................................................................................................................................................... 28
Parallel Signal Format ........................................................................................................................................................ 29
Parallel Data Format ........................................................................................................................................................... 29
2
I C Timing Specification ...................................................................................................................................................... 31
2
I C Device Address Modes ................................................................................................................................................. 32
Schematic Example ............................................................................................................................................................ 33
Dimensions and Patterns ........................................................................................................................................................... 34
Additional Information ................................................................................................................................................................ 36
Revision History ......................................................................................................................................................................... 37
Rev 1.05
Page 3 of 38
www.sitime.com
SiT5156
1 MHz to 60 MHz, ±0.5 to ±2.5 ppm, Elite Platform™ Super-TCXO
Electrical Characteristics
All Min and Max limits are specified over temperature and rated operating voltage with 15 pF output load unless otherwise
stated. Typical values are at 25°C and 3.3V Vdd.
Table 1. Output Characteristics
Parameters
Nominal Output Frequency Range
Operating Temperature Range
Symbol
F_nom
T_use
Min.
1
-20
-40
-40
Frequency Stability over
Temperature
Initial Tolerance
Supply Voltage Sensitivity
F_stab
–
–
–
F_init
F_Vdd
–
–
–
–
Output Load Sensitivity
F_load
–
–
–
Frequency vs. Temperature Slope
ΔF/ΔT
–
–
–
Dynamic Frequency Change during
Temperature Ramp
One-Year Aging
20-Year Aging
F_dynamic
–
–
–
F_1y
F_20y
–
–
Typ.
–
–
–
–
–
–
–
–
±7.10
±11.83
±28.40
±0.81
±1.35
±3.24
±15
±25
±60
±0.13
±0.21
±0.50
±1
±2
Max.
60
+70
+85
+105
±0.5
±1.0
±2.5
±1
±16.25
±32.50
±65.0
±2.75
±5.50
±11.00
±25
±50
±100
±0.21
±0.42
±0.83
–
–
Unit
MHz
°C
°C
°C
ppm
ppm
ppm
ppm
ppb
ppb
ppb
ppb
ppb
ppb
ppb/°C
ppb/°C
ppb/°C
ppb/s
ppb/s
ppb/s
ppm
ppm
Initial frequency at 25°C at 48 hours after 2 reflows
1. Chip information
1) 26LS32: Receiver chip, receives the differential signals A/A-, B/B-, Z/Z- from the encoder output, converts them into single-ended signal output, and after pulse shaping by 74HC...
A machine has a word length of 32 bits and a single-word instruction. The instruction system has a number of two-address instructions, one-address instructions, and zero-address instructions (i.e., at...
When a PDA is used as a device, the PC may use it as a storage device. However, I also want to run a program on the PDA and communicate with the PC to transfer data through the USB interface. Is this ...
I've been studying the online programming of DSP 28335 recently and encountered the following problem: before erasing FLASH, the communication is normal, but once FLASH is erased, the communication be...
Current sensing resistors, also known as shunts, are the technology of choice for measuring current. In order not to adversely affect the current, the shunt has a small resistance value, which produce...
I bought the 51 board on Taobao a month ago. I am busy at work during the day and only go home to study at night and on weekends.
I/O port output high and low, light up a light-emitting diode, etc. I ...
Assume that data is read from 8-bit AD (if it is a higher-bit AD, the data type can be defined as int), the subroutine is get_ad();
1. Limited secondary filtering
/* A value can be adjust...[Details]
A single-chip microcomputer is also called a single-chip microcontroller. It is not a chip that completes a certain logical function, but a computer system integrated into one chip. In general, a c...[Details]
1. Overview
Will passive devices
produce nonlinear intermodulation distortion? The answer is yes! Although there is no systematic theoretical analysis, it has been found in engineerin...[Details]
Microcontrollers (MCUs), which are widely used in automotive electronics, are rapidly facing time and cost pressures. The main advantage of using MCUs has always been to create high-level system in...[Details]
Floating-point digital signal processing has become a constant requirement for precision technology, often in applications requiring high accuracy in areas such as aviation, industrial machinery, a...[Details]
1 Introduction
Solar street lights are mainly composed of four parts: solar photovoltaic cell components, batteries, charge and discharge controllers, and lighting fixtures. The bo...[Details]
With the continuous improvement of the requirements of intelligent building security systems and the continuous improvement of people's safety awareness, indoor anti-theft has gradually attracted peop...[Details]
Overview
In spectral measurement, photomultiplier tubes (PMT) and charge-coupled devices (CCD) are often used as photoelectric converters. PMT is used in slow-changing, high-precision spectral...[Details]
LED technology has made rapid progress, and improvements in chip design and materials have promoted the development of brighter and more durable light sources, and the scope of light source applica...[Details]
This article discusses the six design steps of LED lighting system design in detail: (1) determine the lighting requirements; (2) determine the design goals and estimate the optics; (3) the efficie...[Details]
introduction
Belt drive is a common transmission device used in industrial production. Its commonly used speed detection device is a photoelectric encoder installed at the rotating end of th...[Details]
Applying fieldbus technology on new beer production lines is the first choice for large beer companies with strong management level and technical strength. Guangzhou Zhujiang Beer Group Co., Ltd. i...[Details]
UDN2916LB is a two-phase stepper motor bipolar driver integrated circuit launched by SANKEN. It can drive dual-winding bipolar stepper motors and is particularly suitable for controlling dual-step ...[Details]
introduction
As
a
software
development platform in the field of professional measurement and control, LABVIEW contains rich data acquisition, data signal analysis and powerful DAQ a...[Details]
O Introduction
Virtual instrument is a new type of instrument developed with
the development of
computer
technology, electronic measurement technology and communication technology. ...[Details]
DSP and ARM Processors
京公网安备 11010802033920号
EEWORLD
