EEWORLDEEWORLDEEWORLD

Part Number

Search

3EQHM572-B-55.990N-D1.8

Description
CMOS Output Clock Oscillator, ROHS COMPLIANT, MINIATURE, SMD, 4 PIN
CategoryPassive components    oscillator   
File Size270KB,3 Pages
ManufacturerEuroquartz
Websitehttp://www.euroquartz.co.uk/
Environmental Compliance
Download Datasheet Parametric View All

3EQHM572-B-55.990N-D1.8 Overview

CMOS Output Clock Oscillator, ROHS COMPLIANT, MINIATURE, SMD, 4 PIN

3EQHM572-B-55.990N-D1.8 Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
MakerEuroquartz
Reach Compliance Codecompliant
JESD-609 codee4
Oscillator typeCMOS
Terminal surfaceGold (Au) - with Nickel (Ni) barrier
Base Number Matches1
EURO
QUARTZ
Provides from 8dB to 15dB reduction in system EMI
‘Drop-in’ replacement for standard clocks
Choice of modulation rate and spread
Miniature package: 7.0 mm x 5.0 mm x 1.4mm
N Group parts provide a low cost EMI reduction solution
3EQHM572N Low EMI Oscillator
Page 1 of 3
7 x 5 x 1.4mm SMD - Group 'N'
In electrical systems the principal cause of electro-
magnetic interference (EMI) is the system clock
oscillator. Traditional methods of 'patching-up' systems
with too high a level of EMI is to use ferrite beads,
filters, ground planes, metal shielding and similar costly
methods, However, the most efficient and economic
method to reduce EMI is to reduce it at source: replace
the system clock ocillator with a low EMI clock oscillator.
Compared with conventional clock oscillators, Spread
Spectrum (Dithered) Oscillators can reduce EMI by as
much as 16dB. The part is a 'drop-in' replacement for a
standard clock oscillator hence there is no requirement
to re-design existing PCBs.
DESCRIPTION
EQHM572 series low EMI oscillators can reduce system EMI from 8dB
to 16dB. The oscillators are a ‘drop-in’ replacement for standard
oscillators. EMI reduction is achieved by the use of Spread Spectrum
Technology whereby the mode energy is spread over a wider
bandwidth. The modulation carrier frequency, operating in the kHz
region, makes the process transparent to the oscillator frequency.
There is a choice of modulation rates and spread to suit application
requirements.
SPREAD SPECTRUM TECHNOLOGY
Unlike a conventional clock oscillator, in a Spread Spectrum Clock
Oscillator the mode energy is spread over a wider bandwidth. This is
achieved by the frequency modulation technique. The controlled
modulation process may be applied to the 'down' side of the nominal
frequency (known as
DOWN SPREAD,)
or spread equally either side
of nominal (CENTRE
SPREAD).
Down Spread is preferred if over-
clocking would cause a problem to the system.
APPLICATIONS
Printers, Multiple Function Printers (MPCs)
Digital Copiers; PDAs
Networking: LAN/WAN; Routers
Storage Systems (CD-ROM, VCD, DVD, HDD)
Scanners; Modems; Projectors
Embedded Systems
Musical Instruments
Automotive: GPS car navigation systems
LCD PC Monitors; LSD TVs
ADSL; PCMCIA
Still Digital Cameras (SDCs)
Medical devices
MODULATION TYPES - EXAMPLES
EUROQUARTZ LIMITED Blacknell Lane CREWKERNE Somerset UK TA18 7HE
Tel: +44 (0)1460 230000 Fax: +44 (0)1460 230001 info@euroquartz.co.uk www.euroquartz.co.uk
MTS Displacement Sensors
The R series displacement sensor developed by MTS is a modular " intelligent " displacement sensor. It provides high-speed, reliable and accurate data processing and communication. The position and sp...
shbj Sensor
Some problems in simulating op amp integrator circuit using multisim
[i=s] This post was last edited by dontium on 2015-1-23 13:36 [/i] I used software to simulate several simple integrator circuits, but the output waveform showed a DC component. I don't know why, but ...
hy5239 Analogue and Mixed Signal
Newbie asks: Compilation of STM32IAP in AN2557
I am a novice learning...Now I have downloaded AN2557 and directly run the project an2557\STM32F10x_AN2557_FW_V3.1.0\Project\IAP\RVMDK\IAP.uvproj. The compilation error is as follows:linking....\Obj\S...
emile1732 stm32/stm8
Why is the PI Quiz always like this?
The message says that the information was submitted illegally [click here to return to the previous page] Is it a network problem?...
hahadiy Suggestions & Announcements
How to remove the automatic feedback information of the serial port of the development board s3c2410?
How to remove the automatic feedback information of the serial port of the development board s3c2410? For example, connect the development board and the PC, open the serial port software on the PC, an...
ozx0512 Embedded System
The microcontroller is plugged in and the driver is installed, but it keeps showing that the device has not been migrated and needs further installation. What can I do?
[img]file:///C:\Users\wangzhaohai\AppData\Roaming\Tencent\Users\1416605783\QQ\WinTemp\RichOle\6OS1H)AKG2XDK7`{IZ0T)TF.png[/img]...
onepartner 51mcu

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 957  1125  140  1232  130  20  23  3  25  33 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号