General Electrical, Physical, and Environmental Characteristics
Test Procedures:
Section J of the catalog covers the
applicable test procedures
Humidity Test:
The Non-Hermetically sealed units shall be
tested as outlined in section J “Humidity Test”
As a result of the test there shall be:
• No visible damage
• Max.
∆
C of ± 5%
• Min. IR = 50% of initial limit
• Max. DF = .5%
Electrical Characteristics:
Capacitance, Dissipation Factor, Insulation
Resistance, and Dielectric Strength shall be
measured as specified in section J.
Physical Characteristics:
The Lead Strength shall be measured as
specified in section J.
DC Life:
810P, 820P, 842P & 860P: 140% of rated voltage at 125°C for 250 hours.
832P & 880P: 125% of rated voltage at 150C for 250 hours.
882P: 125% of rated voltage for 250 hours at 125C.
As a result of the test there shall be:
• No permanent open or short circuit
Environmental Characteristics:
Vibration Test: (Condition B)
No mechanical damage, short, open or
intermittent circuit
• No visible damage
• Max.
∆
C of ± 5%
• Min. IR = 50% of initial limit
Moisture Resistance:
The hermetically sealed units shall be tested
as outlined in the Moisture Resistance testing
of section J.
As a result of the test there shall be:
• No visible damage
• Max.
∆
C of ± 5%
• Min. IR = 50% of initial limit
• Max. DF = .5%
• Max. DF = 0.3%
AC Life:
The 859P shall be tested at 110% of the
rated rms voltage at 400 Hz for 250 hours at 85°C.
As a result of the test there shall be:
• No permanent open or short circuit
• No visible damage
• Max.
∆
C of ± 5%
• Min. IR = 50% of initial limit
• Max. DF = 0.5%
F-2
electronics
,
inc.
METALIZED POLYPHENYLENE SULFIDE FILM CAPACITORS
F3
electronics
,
inc.
POLYPHENYLENE SULFIDE FILM CAPACITORS
STYLES FOR METAL-CASE FILM CAPACITORS
SECTION GROUNDED TO CASE
SECTION INSULATED FROM CASE
DIMENSIONS IN INCHES
DIMENSIONS IN INCHES
CASE STYLE 01
+1.00
-0
1.625
CASE STYLE 02
±0.031
0.172 MAX
L
±0.031
+1.00
-0
1.625
0.172
MAX
1.625
+1.00
-0.00
L
D
-0.005
±0.015
DIA
D
+0.015
-0.005
CASE STYLE 04
+1.00
-0
1.625
±0.015
0.020
1.625
+1.000
-0.000
CASE STYLE 03
+1.00
-0
1.625
±0.015
0.020
L
±0.062
L
±0.31
0.020
±0.015
0.172
MAX
0.172
MAX
INSULATING SLEEVE
0.0075 MAX THICKNESS
D
+0.015
-0.005
D
+0.015
-0.037 DIA.
INSULATING SLEEVE
0.0075 MAX THICKNESS
CASE STYLE 12
1.625
+1.00
-0
CASE STYLE 13
1.625
+1.00
-0
1.625
+1.000
-0.000
WRAP-AROUND
APPROX. 135°
FOR 0.400 DIA.,
AND APPROX.
225° FOR LARGER DIA.
DIA
0.172
MAX
L
D
±0.031
L
±0.031
+0.015 DIA
-0.005
C
L
0.172
MAX
C
L
D
-0.005
±0.015
A
±0.005
DIA
C B
W
±0.015
0.033
±0.005
FOR 0.400 DIA.,
0.051
±0.005
FOR DIA. 0.500
AND LARGER
±0.005
A
DIA
C B
W
±0.015
0.033
±0.005
FOR 0.400
DIA., 0.051
±0.005
FOR
DIA. 0.500 AND LARGER
Bracket Dimensions (Style 12 & 13)
Inches
D
0.400
0.500
0.562
0.670
0.750
1.000
W
0.250
0.500
0.500
0.500
0.500
0.500
A
0.144
0.156
0.156
0.156
0.156
0.156
B
0.187±0.015
0.250±0.031
0.250±0.031
0.250±0.031
0.250±0.031
0.250±0.031
C
0.312±0.031
0.437±0.062
0.437±0.062
0.437±0.062
0.437±0.062
0.437±0.062
dimensionsbrac style 12 and 13
F4
electronics
,
inc.
POLYPHENYLENE SULFIDE FILM CAPACITORS
TYPICAL TAB TERMINAL DIMENSIONS
0.020
c
L
±0.005
0.125
±0.015
c
L
SLOT 0.062 x 0.125
A
B
0.296
±0.062
Dwg. No A-9525
A = 0.156 ± 0.015" (3.96 ± 0.38mm)
B = 0.187 ± 0.015" (4.75 ± 0.38mm)
Tab Terminal available only on case diameters equal to or greater than 0.400 inches.
T1 & T3 s t y l e s a r e s u p p l i e d w i t h o n e t a b t e r m i n a l o n t h e i n s u l a t e d e n d a n d a g r o u n d lead on the opposite end.
CATALOG NUMBERING SYSTEM
EXAMPLE:
859P
183
X9
165
S
02
STYLE NUMBER.
SEE PAGE 4 FOR STYLE VARIATIONS
AND CORRESPONDING DIMENSIONS. (Metal case only)
TERMINAL.
S = WIRE LEADS, T = SOLDERING TAB*
*SOLDERING TABS ARE A VAILABLE ONLY ON CASE
DIAMETERS EQUAL TO OR GREATER THAN 0.400
INCHES. (Metal case only)
AC or DC VOLTAGE RATING.
EXPRESSED IN VOLTS. SEE STANDARD
RATINGS CHARTS FOR VOLTAGE CODE.
CAPACITANCE TOLERANCE.
X0 = ±20%; X9 = ±10%
X5 = ± 5%; X2 = ±2%
X1 = ± 1%
CAPACITANCE.
EXPRESSED IN PICOFARADS. THE FIRST TWO DIGITS ARE SIGNIFICANT
FIGURES; THE THIRD IS THE NUMBER OF ZEROS FOLLOWING. SEE STANDARD RATINGS
TABLES FOR CAP ACITANCE CODE. e.g. 183 = 18000pf or 0.018µf
How can 2MFLASH be connected to the EMIFA port of C6416? AEA[22:3]seems to read the program into DSP memory through SDRAM. I hope an expert can give a detailed answer! !...
[i=s]This post was last edited by 1nnocent on 2020-8-13 18:03[/i]In the book Switching Power Supply Design (3rd Edition),The logical relationship behind this is that the EA output voltage decreases, w...
I'm going to share 7 tips for embedded system development. These are the experiences I learned with my friends at Oushi Electronics. I hope they will be helpful to you. Tip 1 - Fill ROM with known val...
This is a simple design, I hope it can be used as a reference. Main circuit: bidirectional thyristor controls the circuit opening and closing.Measurement circuit: differential amplifier circuit design...
On August 24th, Tesla CEO Elon
Musk
revealed information about the upcoming FSD V14, claiming it will outperform human drivers. Tesla FSD lead Ashok stated last year that FSD version 12.5, ...[Details]
A line scan lens is an industrial lens used with line scan cameras. Its imaging principle is to capture the image of the workpiece using a linear sensor and then perform digital signal processing t...[Details]
Nios II is a configurable 16-/32-bit RISC processor. Combined with a rich set of peripheral-specific instructions and hardware acceleration units, it provides a highly flexible and powerful SOPC sy...[Details]
As the number of cars increases, environmental pressures are also increasing. At this time, some people are saying that new energy vehicles are energy-efficient and environmentally friendly, and ar...[Details]
As the main model among new energy vehicles, pure electric vehicles have received strong support and encouragement from the country in recent years, and their development is changing with each pass...[Details]
Robotics
has become
LiDAR
's "second growth curve."
While LiDAR was still battling with its "pure vision" rivals in the automotive field, another field ignited the demand f...[Details]
On August 18th, Galaxis, a specialist in integrated intelligent intralogistics robotics, officially unveiled its next-generation, ultra-narrow aisle forklift mobile robot, the "VFR Ultra-Narrow Ser...[Details]
The all-new MG4 was recently officially announced on the Ministry of Industry and Information Technology's (MIIT) new vehicle announcement. The all-new MG4's semi-solid-state battery version addres...[Details]
One of the most core components of electric vehicles is the motor. The power supply provides electrical energy to the motor, which converts this electrical energy into mechanical energy, which in t...[Details]
Electric vehicles' 12V batteries don't rely on a generator to power them. Only gasoline-powered vehicles rely on the engine to drive a generator to generate electricity while driving, which is used...[Details]
1. Ease of Use: The HMI module should be designed to be simple and clear, allowing users to easily operate and configure the energy storage device.
2. Ease of Maintenance: The HMI module should...[Details]
UPS stands for Uninterruptible Power Supply, which includes energy storage devices. It is mainly used to provide uninterruptible power supply for devices that require high power stability.
...[Details]
A half-bridge is an inverter topology for converting DC to AC. A typical half-bridge circuit consists of two controller switches, a three-wire DC power supply, two feedback diodes, and two capacito...[Details]
On August 22, according to CNBC's report today, the National Highway Traffic Safety Administration (NHTSA) is launching an investigation into Tesla, and the latter is questioned whether it has fail...[Details]
Coal mines typically contain gas and coal dust. When gas and coal dust reach a certain concentration, they can cause explosions. Electrical equipment generates arcs during normal operation or durin...[Details]
Microcontroller MCU
京公网安备 11010802033920号
EEWORLD
