EEWORLDEEWORLDEEWORLD

Part Number

Search

332A1C105J

Description
Film Capacitor, Polyphenylene Sulphide, 200V, 5% +Tol, 5% -Tol, 1uF, Through Hole Mount, RADIAL LEADED
CategoryPassive components    capacitor   
File Size984KB,14 Pages
ManufacturerElectrocube Inc
Websitehttps://www.electrocube.com/
Environmental Compliance  
Download Datasheet Parametric View All

332A1C105J Overview

Film Capacitor, Polyphenylene Sulphide, 200V, 5% +Tol, 5% -Tol, 1uF, Through Hole Mount, RADIAL LEADED

332A1C105J Parametric

Parameter NameAttribute value
Is it lead-free?Lead free
Is it Rohs certified?conform to
Objectid1679647949
package instruction,
Reach Compliance Codecompliant
Country Of OriginUSA
ECCN codeEAR99
YTEOL6.95
capacitance1 µF
Capacitor typeFILM CAPACITOR
dielectric materialsPOLYPHENYLENE SULPHIDE
JESD-609 codee3
Manufacturer's serial number332A
Installation featuresTHROUGH HOLE MOUNT
negative tolerance5%
Number of terminals2
Maximum operating temperature125 °C
Minimum operating temperature-55 °C
Package shapeRECTANGULAR PACKAGE
positive tolerance5%
Rated (DC) voltage (URdc)200 V
surface mountNO
Terminal surfaceTin (Sn)
Terminal shapeWIRE
®
electrocube
METALLIZED POLYPHENYLENE SULFIDE
330 SERIES
SERIES NO.
DESCRIPTION
330B
FLAME RETARDANT
WRAP AND FILL, OVAL
330C
FLAME RETARDANT
WRAP AND FILL, FLAT
330D
FLAME RETARDANT
WRAP AND FILL, ROUND
332A
FLAME RETARDANT
EPOXY CASE,
RECTANGULAR
RADIAL LEADS
333A
FLAME RETARDANT
EPOXY CASE,
RECTANGULAR
AXIAL LEADS
351D
HERMETIC SEAL
ROUND CONFIGURATION
AXIAL LEADS
electrocube
Drawn: Justin Salaises
3366 Pomona Blvd • Pomona, CA 91768 • TEL: (909) 595-4037 • FAX: (909) 595-0186
e-mail:
esales@electrocube.com
• Internet :
www.electrocube.com
• (IR: 9/09)
ADuCM360 interrupt problem,
After ADuCM360 enters interrupt, the manual does not explain how to clear the interrupt again. I thought it would be cleared after entering interrupt, but when debugging, I found that after entering i...
dontium ADI Reference Circuit
How to start Wince system without BOOTLOADER?
Usually when we load the wince system, we always compile the eboot and then download it to the flash, and then download NK according to the menu prompts. In actual products, BOOTLOADER is not needed, ...
xioajinglchy Embedded System
Siemens s7200 programming problem
Why can't Q0.2 be turned on when M1.0 becomes 1, but Q0.2 is turned on when M1.1 becomes 1?...
eeleader Industrial Control Electronics
Make a timer with C51
Give me the following program to add a pause and clear function //Main program #includesbit ksec=P3^0; sbit kmin=P3^1; sbit khour=P3^2; unsigned char secshi=0,secge=0,minshi=0,minge=0,hourshi=0,hourge...
jianghan 51mcu
DAC8552 chip pin problem?
SPI (SYNC, MOSI, MISO, SCK) has these 4 wires. I checked a lot of information on the Internet. Generally, chips that use SPI have these 4 wires, which means that the chip can be read or written. But r...
猎狐梦痕 Analogue and Mixed Signal
A small question about 5509gpio, thank you everyone
1. For example, the iodir address of gpio in the manual is 0x3400, and the address of iodata is 0x3401. Now if I need to output a 1 to gpio6, assuming that gpio6 has been set to output state, can I ju...
ganweixu DSP and ARM Processors

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1256  597  2763  2220  160  26  13  56  45  4 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号