EEWORLDEEWORLDEEWORLD

Part Number

Search

FC5AQBHVC16.0-T1

Description
Parallel - Fundamental Quartz Crystal, 16MHz Nom, SMD, 2 PIN
CategoryPassive components    Crystal/resonator   
File Size198KB,2 Pages
ManufacturerFOX [Fox Electronics]
Environmental Compliance
Download Datasheet Parametric View All

FC5AQBHVC16.0-T1 Overview

Parallel - Fundamental Quartz Crystal, 16MHz Nom, SMD, 2 PIN

FC5AQBHVC16.0-T1 Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
MakerFOX [Fox Electronics]
package instructionSMD, 2 PIN
Reach Compliance Codecompliant
Ageing5 PPM/YEAR
Crystal/Resonator TypePARALLEL - FUNDAMENTAL
Drive level500 µW
frequency stability0.001%
frequency tolerance50 ppm
load capacitance7 pF
Installation featuresSURFACE MOUNT
Nominal operating frequency16 MHz
Maximum operating temperature70 °C
Minimum operating temperature
physical size5mm x 3.2mm x 1.2mm
Series resistance80 Ω
surface mountYES
Base Number Matches1
5.0mm x 3.2mm SMD Crystal
Tolerances down to 20 PPM
Stabilities down to 10 PPM
C5AQ
(former FQ5032A)
DATASHEET
Page
1
of
2
• C5BQ STANDARD SPECIFICATIONS
PARAMETERS 
Frequency Range
(Fo)
Frequency Tolerance @ 25ºC
Frequency Stability, ref @ 25ºC
Over Operating Temp Range
Temperature Range
(T
OPR
)
Operating
(T
STG
)
Storage
Shunt Capacitance
(Co)
Load Capacitance
(C
L
)
Drive Level
Aging per year
Termination Finish
Seal Method
Lead (Pb) Free
RoHS Compliant
MAX 
(unless otherwise noted)
8.000 ~ 48.000 MHz
(See options on page 2)
(See options below)
(See options below)
-40ºC ~ +85ºC
5 pF
(See options on page 2)
0.5 mW
±5 PPM
Ag
Resin
Yes
Yes
Frequency Range
(MHz)
Operating Mode
Max ESR
8.000000 ~ 11.999999
12.000000 ~ 16.000
16.000001 ~ 48.000
Fundamental
Fundamental
Fundamental
100
80
50
All dimensions are in millimeters.
Note: Dimensional drawing is for reference to critical specifications
defined by size measurements. Certain non-critical visual attributes,
such as side castellations, etc. may vary.
• Available Operating Temperatures and Stabilities*
±15 PPM
±20 PPM
±25 PPM
O
O
O
O
0 ~+70ºC
O
O
O
O
-20 ~+70ºC
X
X
X
X
-40 ~+85ºC
Key: O=Available, X=Not Available, ∆=Consult Fox Technical Support
*Does not imply a stocked part.
Stability Temperature
±10 PPM
±30 PPM
O
O
O
±50 PPM
O
O
O
© Copyright 2019 Fox Electronics. All rights reserved
Title / Description:
C5AQ SERIES STANDARD SPECIFICATIONS
Drawing Number:
101148
Size: A
Part Number:
Cage:
61429
Draftsperson: BEC
Approved: MAJ
Revision Date:
04/16/2019
Looking for an example of controlling UART reading and writing via SPI in SC16IS762 -- urgent!!!
Hi guys, I want to write the code about how to control UART read and write through SPI in SC16IS762. I have read the SPEC of this IC, which has the format of how to control the internal register of UA...
qu27jump Embedded System
Award-winning review: Sensirion SEK-SVM40 is coming in the new year, easily monitor indoor air quality and test whether it is "good luck"
This week is the last week for evaluation application. If you want to participate, pleaseclick here to apply. The New Year is here, and it looks like I’ll be staying at home for another Spring Festiva...
EEWORLD社区 Sensor
Problem with s3c2451 timer, T2 and T3 clocks are slow and occupy system resources?
I am using 4 timers of tiny2451 from FriendlyArm for PWM output. Timers T0 and T1 work fine, but when timer T2 or T3 is turned on, the system becomes stuck, and T0 and T1 also become slower. It takes ...
suhaozi ARM Technology
Can G2452 drive this screen? Can an expert give me a code?
I have an 8-bit screen with these interfaces GND, VCC, RS.RD, CS, RESET.WR and eight data bits from D0 to D7. I want to ask, can it be driven by G2452? Please give me the code[[i]This post was last ed...
smallbird Microcontroller MCU
[Domestic digital isolation chip replacement] Nanochip MSI series replaces ADI ADUM and TI IOS series isolation chips
[i=s]This post was last edited by nemo1991 on 2021-3-28 22:36[/i]Digital isolation chips are commonly used in industrial control and power supplies.For example, in power supply design, the power signa...
nemo1991 Domestic Chip Exchange
USB-Blaster cannot be used
As shown in the figure, this situation always occurs when connecting to the FPGA development board. I have tried several development boards and many methods, but it doesn't work even with a digital si...
Porang FPGA/CPLD

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1903  569  2778  125  164  39  12  56  3  4 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号