EEWORLDEEWORLDEEWORLD

Part Number

Search

177-710-5-100GP6J1-18MSN

Description
Cable Assembly, 26AWG,
File Size858KB,5 Pages
ManufacturerGlenair
Websitehttp://www.glenair.com/
Environmental Compliance
Download Datasheet Parametric View All

177-710-5-100GP6J1-18MSN Overview

Cable Assembly, 26AWG,

177-710-5-100GP6J1-18MSN Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
Objectid7004924408
Reach Compliance Codecompliant
Country Of OriginUSA
YTEOL8.75
Other featuresSTANDARD: MIL-DTL-83513, EMI SHIELDED
CertificationMIL
Conductor surface treatmentSILVER
conductor materialCOPPER
ConnectorSide1MICRO-D MALE
ConnectorSide2MICRO-D MALE
Connector bracket typeCABLE ASSEMBLY
structureSTRANDED
Cross-sectional area0.129 mm2
DIN complianceNO
IEC complianceNO
insulator materialCROSSLINKED ETHYLENE-TETRAFLUOROETHYLENE
length0.466 mm
MIL complianceYES
Number of conductors100
Maximum operating temperature150 °C
Minimum operating temperature-55 °C
Rated current3 A
Rated voltage150 V
resistance0.147 Ω
shieldYES
stay19X38
Wire gauge26 AWG
Wire and Cable NamesFLEXIBLE CORD AND FIXTURE WIRE
B
SHIELDING EFFECTIVENESS (Db)
1.00E+04
1.00E+05
1.00E+06
1.00E+07
1.00E+08
1.00E+09
SHIELDING EFFECTIVENESS (Db)
Micro-D Harness
EMI Performance with Ground Spring
100
90
80
70
60
50
40
30
20
10
0
1.00E+03
MWDM Micro-D
Shielded Cable Assembly
Single-Ended or Double-Ended–These
easy-to-order cable
assemblies eliminate the need for expensive assembly labor. 100%
tested and ready for use.
Now With Twisted Pairs–No
need to create a procurement
specification for Micro-D cables with twisted pairs. Glenair 177-740
cables are furnished with a full complement of white/blue twisted
pair wires.
Integral Shield Termination–The
connector shell has a platform
to accept Band-It shield termination bands. The cable shield braid is
attached directly to the connector.
Save Labor, Reduce Weight and Improve EMI Shielding
with Glenair’s Micro-D Shielded Cable Assemblies
Aerospace electronics systems require higher and higher levels of protection from radiated emissions. Glenair’s
fully shielded Micro-D cable assemblies meet this need. The cable shield is attached directly onto the one-
piece connector shell and secured with a stainless steel
Band-Master™ ATS
clamp. These pre-wired, 100% tested
assemblies meet the requirements of MIL-DTL-83513. An optional ground spring on the pin connector assures low
shell-to-shell resistance. Available with a variety of wire types and shields, Micro-D shielded assemblies can be
ordered in any length, either single-ended or “back-to-back”.
Ground Spring and EMI Shielding Effectiveness
A gold-plated stainless steel ground spring on the pin connector mating
face offers substantial improvement in EMI protection. The graphs
compare identical connectors tested with and without ground springs.
EMI Performance without Ground Spring
100
90
80
70
60
50
40
30
20
10
0
1.00E+03
1.00E+04
1.00E+05
1.00E+06
1.00E+07
1.00E+08
1.00E+09
frequency (Hz)
frequency (Hz)
© 2013 Glenair, Inc.
High Performance Micro-D Connectors and Cables
U.S. CAGE Code 06324
Printed in U.S.A.
GLENAIR, INC.
1211 AIR WAY
GLENDALE, CA 91201-2497
818-247-6000
FAX 818-500-9912
www.glenair.com
B-14
E-Mail: sales@glenair.com
Has anyone used L293D?
I use L293D to drive the motor. V1 is connected to 24V power supply and V2 is connected to 5V power supply. Then I am ready to control the forward and reverse rotation of the motor. A1, A2, EN1 are co...
wcf8051 Embedded System
s3c6410 nandflash partition problem, formatting binfs, exfat destroyed
Now I'm learning on the ut development board, and I want to change the partition method of nandflash: 256MB flash ------ bootloader ------ TOC ------ eboot ------ MBR ------ nk.bin, //binfs ------ exf...
yuyang4812 Embedded System
Brief analysis of the working principle of DSP
There are two ways to understand DSP:  1) Broadly speaking: digital signal processing;  it uses a digital signal processing system to process signals in digital form, and finally obtains a signal form...
Aguilera DSP and ARM Processors
VHDL design example and simulation stopwatch program
I followed the procedure in the book and tested it with Tianxiang's CPLD learning board, but it failed. There was no response when pressing the buttons. Please have a look. Use QUARTUS II 8.1. Externa...
acetuo FPGA/CPLD
How to develop FTP program on WINCE5 platform using VS2005? I want to use it to realize automatic update.
How to develop FTP program on WINCE5 platform with VS2005? I want to use it to realize automatic update? We have developed a program on WINCE handheld scanner, and want to realize automatic update wit...
push Embedded System
TL16c754 extended serial port
Has anyone used the TL16c754 chip? Does it support up to 56000@1.7432MHz and 38400@3.072MHz?...
sonic Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1839  2908  918  1373  1917  38  59  19  28  39 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号