EEWORLDEEWORLDEEWORLD

Part Number

Search

177-710-5-51-2GP6J5-18MSG

Description
Cable Assembly, 26AWG,
File Size858KB,5 Pages
ManufacturerGlenair
Websitehttp://www.glenair.com/
Environmental Compliance
Download Datasheet Parametric View All

177-710-5-51-2GP6J5-18MSG Overview

Cable Assembly, 26AWG,

177-710-5-51-2GP6J5-18MSG Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
Objectid7004959827
Reach Compliance Codecompliant
Country Of OriginUSA
YTEOL8.75
Other featuresSTANDARD: MIL-DTL-83513, EMI SHIELDED
CertificationMIL
Conductor surface treatmentSILVER
conductor materialCOPPER
ConnectorSide1MICRO-D MALE
ConnectorSide2MICRO-D MALE
Connector bracket typeCABLE ASSEMBLY
structureSTRANDED
Cross-sectional area0.129 mm2
DIN complianceNO
IEC complianceNO
insulator materialCROSSLINKED ETHYLENE-TETRAFLUOROETHYLENE
length0.466 mm
MIL complianceYES
Number of conductors51
Maximum operating temperature150 °C
Minimum operating temperature-55 °C
Rated current3 A
Rated voltage150 V
resistance0.147 Ω
shieldYES
stay19X38
Wire gauge26 AWG
Wire and Cable NamesFLEXIBLE CORD AND FIXTURE WIRE
B
SHIELDING EFFECTIVENESS (Db)
1.00E+04
1.00E+05
1.00E+06
1.00E+07
1.00E+08
1.00E+09
SHIELDING EFFECTIVENESS (Db)
Micro-D Harness
EMI Performance with Ground Spring
100
90
80
70
60
50
40
30
20
10
0
1.00E+03
MWDM Micro-D
Shielded Cable Assembly
Single-Ended or Double-Ended–These
easy-to-order cable
assemblies eliminate the need for expensive assembly labor. 100%
tested and ready for use.
Now With Twisted Pairs–No
need to create a procurement
specification for Micro-D cables with twisted pairs. Glenair 177-740
cables are furnished with a full complement of white/blue twisted
pair wires.
Integral Shield Termination–The
connector shell has a platform
to accept Band-It shield termination bands. The cable shield braid is
attached directly to the connector.
Save Labor, Reduce Weight and Improve EMI Shielding
with Glenair’s Micro-D Shielded Cable Assemblies
Aerospace electronics systems require higher and higher levels of protection from radiated emissions. Glenair’s
fully shielded Micro-D cable assemblies meet this need. The cable shield is attached directly onto the one-
piece connector shell and secured with a stainless steel
Band-Master™ ATS
clamp. These pre-wired, 100% tested
assemblies meet the requirements of MIL-DTL-83513. An optional ground spring on the pin connector assures low
shell-to-shell resistance. Available with a variety of wire types and shields, Micro-D shielded assemblies can be
ordered in any length, either single-ended or “back-to-back”.
Ground Spring and EMI Shielding Effectiveness
A gold-plated stainless steel ground spring on the pin connector mating
face offers substantial improvement in EMI protection. The graphs
compare identical connectors tested with and without ground springs.
EMI Performance without Ground Spring
100
90
80
70
60
50
40
30
20
10
0
1.00E+03
1.00E+04
1.00E+05
1.00E+06
1.00E+07
1.00E+08
1.00E+09
frequency (Hz)
frequency (Hz)
© 2013 Glenair, Inc.
High Performance Micro-D Connectors and Cables
U.S. CAGE Code 06324
Printed in U.S.A.
GLENAIR, INC.
1211 AIR WAY
GLENDALE, CA 91201-2497
818-247-6000
FAX 818-500-9912
www.glenair.com
B-14
E-Mail: sales@glenair.com
The relationship between H.264 and MPEG-4 standards
[i=s]This post was last edited by jameswangsynnex on 2015-3-3 20:01[/i] 1. Overview of H.264 and the difference between it and MPEG-XWiththe market demand, obtaining good image quality with the lowest...
leslie Mobile and portable
51 MCU Elf, it is said that you can program even if you don't know MCU
[i=s] This post was last edited by paulhyde on 2014-9-15 09:05 [/i] 51 MCU Wizard, it is said that even if you don't know MCU, you can still program. In fact, it is a collection of small tools. I took...
open82977352 Electronics Design Contest
Question: The handset of a telephone is 130 ohms. I have set up a telephone board. How can I modify the headphone circuit so that I can use 30 ohm headphones?
The phone chip used is TEA1062, SPK is connected to the headset through capacitor C; there is a resistor R between SPK and GAR. The test found that: when R = 100K, C = 1UF, the quality of the telephon...
zfnlj Embedded System
pwm brushless ESC N5065 motor
I bought an fvt brushless ESC, an N5065 motor, and used the PWM driver of STM32. Set the throttle range according to the instructions: ****************************************** First turn off the ESC...
liuw2010 Electronics Design Contest
Problems with converting VHDL integer to real
I want to convert integer type signal to real type. The program is as follows. This program reports an error in maxplus II: file standard.vhdl:Unsupported feature error:floating is not supported An er...
力量 Embedded System
XILINX EDK: Get data from the serial port
Hello everyone! I'm learning Xilinx EDK recently, and I'd like to ask you a question. First of all, the board I'm using is ML506, and the software is EDK 11.1. There is a "hello world" program in the ...
applelonger FPGA/CPLD

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2738  375  572  2758  1952  56  8  12  40  7 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号