EEWORLDEEWORLDEEWORLD

Part Number

Search

800-012-07C7-25FZ

Description
Circular Connector
CategoryThe connector    The connector   
File Size1MB,5 Pages
ManufacturerGlenair
Websitehttp://www.glenair.com/
Environmental Compliance
Download Datasheet Parametric View All

800-012-07C7-25FZ Overview

Circular Connector

800-012-07C7-25FZ Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
Objectid7093063498
Reach Compliance Codecompliant
ECCN codeEAR99
Connector typeCIRCULAR CONNECTOR
Series 800 Mighty Mouse UN Mating Thread
PC Tail or Solder Cup PCB Receptacle
800-012 and 800-040 Ordering Information
Printed Circuit Board/ Solder Cup Receptacles
feature low profile shells for
minimum protrusion inside enclosures and integral board standoffs. Contacts are
non-removable.
Water Immersion, Unmated
Specify
800-012
connectors for applications where
open face water immersion is not a requirement. For MIL-STD-810 Method 512G
immersion requirements, specify
800-040
watertight connectors . These 800-040
connectors are specially sealed (“MOD-518”) and are 100% tested to maintain a
helium leak rate of 1 x 10
-4
cc/second at one atmosphere pressure differential from
-40C to +70C.
How To Order
C
Shell
Size
Series 800
Sample Part Number
Series
Shell Style (See Table I)
-02
= Square Flange
Shell Material and Finish
Shell Size - Insert
Arrangement
Contact Type
Shell Key Position
(See Table II)
P
= Pin, PC Tail
S
= Socket , PC Tail
N
= Normal
800-012
800-012
=
Receptacle for Solder Cup or PCB Termination, with Standard
Epoxy Potting
800-040
=
Receptacle for Solder Cup or PCB Termination, With Special
“MOD-518” Sealing For Open Face (Unmated) Water Immersion
Requirements. 100% Leak Tested.
-07
= Jam Nut
(See
Jam Nut Panel Cutout Dimensions Page C-3)
C
= Aluminum / Black Anodize (Non-Conductive) RoHS Compliant
M
= Aluminum / Electroless Nickel RoHS Compliant
NF
= Aluminum / Cadmium with Olive Drab Chromate
ZNU
= Aluminum / Zinc-Nickel with Black Chromate
MT
= Aluminum / Nickel-PTFE RoHS Compliant
Z1
= Stainless Steel / Passivated RoHS Compliant
See Contact Arrangements page C-2
E
= Pin, Solder Cup
F
= Socket, Solder Cup
Y
= Pos. Y
Z
= Pos. Z
-07
M
7-10
P
Z
X
= Pos. X
Table I: Shell Style
ØM
in
.318
.386
.449
.510
.574
.635
.760
mm
8.08
9.80
11.40
12.95
14.58
16.13
19.30
Recommended Panel Cut Out
N Flat ± .002
in
.297/.292
.365/.360
.429/.424
.483
.540
.614
.722
mm
7.54/7.42
9.27/9.14
10.90/10.77
12.67
13.71
15.60
18.34
øM
N FLAT
-02
Square Flange Front Mount
-07
Jam Nut for Rear Panel
Mounting
5
6
7
8
9
10
12
Dimensions in Inches (millimeters) are subject to change without notice.
© 2014 Glenair, Inc.
Series 80 Mighty Mouse
U.S. CAGE Code 06324
Printed in U.S.A.
GLENAIR, INC.
1211 AIR WAY
GLENDALE, CA 91201-2497
818-247-6000
FAX 818-500-9912
www.glenair.com
C-12
E-Mail: sales@glenair.com
Problems using save date
Has anyone used CCS to export programs? When using save date, there will be a requirement to set an address. What principle is used to design this address?...
安_然 Microcontroller MCU
About ADXL203 to measure tilt angle
When using ADXL203 to measure the tilt angle, the output should be 2.5V at 0° and 3.5V at 90°. The outputs I measured in the experiment were 2.5038V and 3.509V, which are basically correct. However, s...
lene ADI Reference Circuit
Use jlink to download the program to stm32, the jlink red light flashes, and finally the microcontroller cannot be recognized
When using jlink's sw mode to download the program, the debug window cannot recognize the MCU. jlink can be downloaded normally on other boards, so there is no problem with jlink, and there is no prob...
研究深 stm32/stm8
How can I create a WINCE emulator running on a PC with an ARMV4I CPU?
How can I use PB to create a WINCE simulator with ARMV4I CPU running on PC? Just explain the key steps. It seems that I cannot select two CPUs. If I select X86 and ARMV4I, there is no corresponding si...
bbs_cq Embedded System
My wireless network is not working, the driver is fine, it was working yesterday but not today
My laptop is ASUS x50sl. It was working fine yesterday, but not today. I installed the system and drivers, but still can't get on, and reports this error: Name: Association test Description: This test...
6562748 Embedded System
Request Wince system customization information
Who has more detailed information about Wince system customization? Can you send me a copy? My email: baiminshengbai@126.com Send me a message and I will give you a copy. Thank you...
heater Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 702  431  419  2157  230  15  9  44  5  46 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号