EEWORLDEEWORLDEEWORLD

Part Number

Search

8N3QV01AG-1124CD8

Description
LVPECL Output Clock Oscillator
CategoryPassive components    oscillator   
File Size229KB,22 Pages
ManufacturerIDT (Integrated Device Technology)
Download Datasheet Parametric View All

8N3QV01AG-1124CD8 Overview

LVPECL Output Clock Oscillator

8N3QV01AG-1124CD8 Parametric

Parameter NameAttribute value
Objectid1266564955
Reach Compliance Codecompliant
Oscillator typeLVPECL
Quad-Frequency Programmable
VCXO
IDT8N3QV01 Rev G
DATA SHEET
General Description
The IDT8N3QV01 is a Quad-Frequency Programmable VCXO with
very flexible frequency and pull-range programming capabilities.
The device uses IDT’s fourth generation FemtoClock® NG
technology for an optimum of high clock frequency and low phase
noise performance. The device accepts 2.5V or 3.3V supply and is
packaged in a small, lead-free (RoHS 6) 10-lead Ceramic 5mm x
7mm x 1.55mm package.
Besides the 4 default power-up frequencies set by the FSEL0 and
FSEL1 pins, the IDT8N3QV01 can be programmed via the I
2
C
interface to any output clock frequency between 15.476MHz to
866.67MHz and from 975MHz to 1,300MHz to a very high degree of
precision with a frequency step size of 435.9Hz ÷N (N is the PLL
output divider). Since the FSEL0 and FSEL1 pins are mapped to 4
independent PLL M and N divider registers (P, MINT, MFRAC and
N), reprogramming those registers to other frequencies under
control of FSEL0 and FSEL1 is supported. The extended
temperature range supports wireless infrastructure, tele-
communication and networking end equipment requirements. The
device is a member of the high-performance clock family from IDT.
Features
Fourth generation FemtoClock® NG technology
Programmable clock output frequency from 15.476MHz to
866.67MHz and from 975MHz to 1,300MHz
Four power-up default frequencies (see part number order
codes), reprogrammable by I
2
C
I
2
C programming interface for the output clock frequency, APR
and internal PLL control registers
Frequency programming resolution is 435.9Hz ÷N
Absolute pull-range (APR) programmable from ±4.5 to
±754.5ppm
One 2.5V or 3.3V LVPECL differential clock output
Two control inputs for the power-up default frequency
LVCMOS/LVTTL compatible control inputs
RMS phase jitter @ 156.25MHz (12kHz - 20MHz):
0.487ps (typical)
RMS phase jitter @ 156.25MHz (1kHz - 40MHz):
0.614ps (typical)
2.5V or 3.3V supply voltage modes
-40°C to 85°C ambient operating temperature
Available in Lead-free (RoHS 6) package
Block Diagram
OSC
114.285 MHz
÷MINT,
MFRAC
2
VC
FSEL1
FSEL0
SCLK
SDATA
OE
Pulldown
Pulldown
Pullup
Pullup
Pullup
Pin Assignment
÷P
PFD
&
LPF
FemtoClock® NG
VCO
1950-2600MHz
÷N
Q
nQ
SDATA
SCLK
10
VC 1
OE 2
V
EE
3
4
FSEL0
9
8
7
V
CC
nQ
Q
5
6
A/D
7
25
Configuration Register (ROM)
(Frequency, APR, Polarity)
I
2
C Control
7
IDT8N3QV01 Rev G
10-lead Ceramic 5mm x 7mm x 1.55mm
package body
CD Package
Top View
IDT8N3QV01GCD REVISION A
FEBRUARY 24, 2012
1
©2012 Integrated Device Technology, Inc.
FSEL1
Installation Case | MODBUS to PROFINET Gateway Connects Smart Low Voltage Motors
The main objects controlled in this case are the motor protector and the display and alarm of various parameters on site. The main PLC uses Siemens CPU, and the Modbus to Profinet gateway module monit...
bjnytx Test/Measurement
[NXP Rapid IoT Review] + Getting Started with NXP Rapid IoT
[NXP Rapid IoT Review] + NXP Rapid IoT Step-by-step Test Purpose: Create a new project, then add, configure, compile, burn and see the running results, step-by-step 1. Log in to [url]https://rapid-iot...
蓝雨夜 RF/Wirelessly
Where can I find the emulator firmware on launchPAD?
Don't know if you can find one? Want to make one yourself...
yirenonege TI Technology Forum
Comprehensive embedded learning and development materials
[Repost] Comprehensive embedded learning and development materials. Because there is a lot of information, we will sort out this part first, and then we will improve and launch the ARM11 6410 area in ...
kangfu915 Embedded System
An interview question solution
Try to analyze the role of C133 in the circuit. Thank you!...
chenbingjy Analog electronics
STM32 external expansion RAM
Dear friends, the internal RAM of STM32 is not enough, and I want to expand an external SRAM. I use IAR FOR ARM 5.30 as the compilation platform, and I find that after using the configuration file stm...
cgl123456 stm32/stm8

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 155  2255  354  1602  2102  4  46  8  33  43 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号