EEWORLDEEWORLDEEWORLD

Part Number

Search

DIP1999SD033573BF

Description
Array/Network Resistor, Isolated, 0.2W, 357000ohm, 100V, 0.1% +/-Tol, -25,25ppm/Cel, 8025,
CategoryPassive components    The resistor   
File Size334KB,3 Pages
ManufacturerTT Electronics plc
Websitehttp://www.ttelectronics.com/
Download Datasheet Parametric View All

DIP1999SD033573BF Overview

Array/Network Resistor, Isolated, 0.2W, 357000ohm, 100V, 0.1% +/-Tol, -25,25ppm/Cel, 8025,

DIP1999SD033573BF Parametric

Parameter NameAttribute value
Is it Rohs certified?incompatible
Objectid791918058
Reach Compliance Codecompliant
Country Of OriginUSA
ECCN codeEAR99
YTEOL5.18
structureWelded
JESD-609 codee0
Lead length3.429 mm
lead spacing2.54 mm
Network TypeIsolated
Number of terminals16
Maximum operating temperature150 °C
Minimum operating temperature-55 °C
Package height2.032 mm
Package length20.32 mm
Package formDIP
Package width6.35 mm
Rated power dissipation(P)0.2 W
resistance357000 Ω
Resistor typeARRAY/NETWORK RESISTOR
series1900
size code8025
Temperature Coefficient25 ppm/°C
Terminal surfaceTin/Lead (Sn60Pb40)
Tolerance0.1%
Operating Voltage100 V

DIP1999SD033573BF Preview

TaNFilm Precision DIP Network
Commercial and MIL Qualified
®
1900 Series
·
·
·
·
·
·
Inherent reliability
MIL-PRF-83401 qualified
Custom configuration available
Bonded leads not susceptible to
solder reflow problems
Absolute tolerance to
±0.1% / ratio tolerance to ±0.05%
Absolute TCR to
±15ppm/°C / ratio tracking to ±5ppm/°C
_____
General Note
TT electronics reserves the right to make changes in product specification without notice or liability.
All information is subject to TT electronics’ own data and is considered accurate at time of going to print.
www.bitechnologies.com www.irctt.com www.welwyn-tt.com
© TT electronics plc
09. 11
TaNFilm
®
Precision DIP Network
Commercial and MIL Qualified
1900 Series
General Note
TT electronics reserves the right to make changes in product specification without notice or liability.
All information is subject to TT electronics’ own data and is considered accurate at time of going to print.
www.bitechnologies.com www.irctt.com www.welwyn-tt.com
© TT electronics plc
09. 11
TaNFilm
®
Precision DIP Network
Commercial and MIL Qualified
1900 Series
General Note
TT electronics reserves the right to make changes in product specification without notice or liability.
All information is subject to TT electronics’ own data and is considered accurate at time of going to print.
www.bitechnologies.com www.irctt.com www.welwyn-tt.com
© TT electronics plc
09. 11
Question: The handset of a telephone is 130 ohms. I have set up a telephone board. How can I modify the headphone circuit so that I can use 30 ohm headphones?
The phone chip used is TEA1062, SPK is connected to the headset through capacitor C; there is a resistor R between SPK and GAR. The test found that: when R = 100K, C = 1UF, the quality of the telephon...
zfnlj Embedded System
pwm brushless ESC N5065 motor
I bought an fvt brushless ESC, an N5065 motor, and used the PWM driver of STM32. Set the throttle range according to the instructions: ****************************************** First turn off the ESC...
liuw2010 Electronics Design Contest
Problems with converting VHDL integer to real
I want to convert integer type signal to real type. The program is as follows. This program reports an error in maxplus II: file standard.vhdl:Unsupported feature error:floating is not supported An er...
力量 Embedded System
XILINX EDK: Get data from the serial port
Hello everyone! I'm learning Xilinx EDK recently, and I'd like to ask you a question. First of all, the board I'm using is ML506, and the software is EDK 11.1. There is a "hello world" program in the ...
applelonger FPGA/CPLD
Breakpoint setting in CCS3.3
1. If breakpoints cannot be set during simulation under CCS3.3. You need to check your project configuration. Open Build Optins, and in Basic under the Complier dialog box, set Generate Debug to Full ...
ltbytyn Microcontroller MCU
Random Questions about Operational Amplifier Circuits
[If you don't understand, ask] What is the function of the op amp in the picture, or what type of op amp does it belong to? If the inductor L is removed, it is very similar to an integrating amplifier...
shaorc Analog electronics

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 967  2571  1867  2262  70  20  52  38  46  2 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号