EEWORLDEEWORLDEEWORLD

Part Number

Search

450X232R106B1F2

Description
Potentiometer, Carbon Composition, 0.25W, 10000000ohm, 750V, 20% +/-Tol
CategoryPassive components    The resistor   
File Size4MB,12 Pages
ManufacturerCTS
Environmental Compliance
Download Datasheet Parametric View All

450X232R106B1F2 Overview

Potentiometer, Carbon Composition, 0.25W, 10000000ohm, 750V, 20% +/-Tol

450X232R106B1F2 Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
Reach Compliance Codeunknown
ECCN codeEAR99
structureRotary
Manufacturer's serial number450(X,METSHA)
Package diameter23.8 mm
Package length11.5 mm
Package formPCB Mount
Rated power dissipation(P)0.25 W
resistance10000000 Ω
Resistor typePOTENTIOMETER
rotation angle300 deg
series450(X,METSHA)
technologyCARBON COMPOSITION
Tolerance20%
Operating Voltage750 V
Series 450
®
Industrial 15/16"
(24mm) diameter
1/2 watt composition
variable resistor
• Low cost
• Versatile mounting styles:
– bushing
– twist tab
– bend tab
– snap-in PC bracket
– solder lug or PC terminals
• Wide resistance range
• Molded or metal shafts
• Pull-push and rotary power switches
• Shaft and bushing waterseal
• Rear extended shaft
• Single, tandem, or concentric constructions
• Special vernier adjust (multiturn) construction
available for fine adjustment
• Long life construction available
Electrical and Mechanical Specifications
Resistance Range
100
through 10 Meg
(linear taper)
Long life construction - 10K
through 5 Meg
(linear taper)
Power Rating, Watts
Vernier Adjust Construction
1
/
2
watt 10K ohms,
1
/
3
watt; above 10K ohms through
100K ohms,
1
/
4
watt above 100K ohms. Full rating @
55°C derated to no load at 85°C, linear taper,
bushing mounted control on steel panel 4" x 4" x
.050" (101.6mm x 101.6mm x 1.27mm).
Voltage Rating
Bushings to Terminals:
High pot test, one minute
Standard construction – 1080VAC
Vernier construction – 1000VAC
Operating maximum – 750VDC
Across End Terminals:
500 VDC, load not to exceed listed wattage ratings.
Special requirement for 1500 VAC Hi-pot is
available.
(continued on next page)
Resistance Tolerance
Standard: ±20%
Special: Closer tolerances available in most resistance
values.
Power Rating, Watts
Standard Construction
1
/
2
watt per section through 100K
1
/
3
watt per section above 100K
Full rating @ 55°C derated to no load at 85°C,
linear taper, bushing mounted control on steel panel
4" x 4" x .050" (101.6mm x 101.6mm x 1.27mm).
(Derating required on two section controls.)
Technical Data Sheet 1448C
Technical Data Sheet 1450B
CTS CORPORATION /
MANUFACTURER OF RELIABLE ELECTRONIC COMPONENTS
New FET switch with high isolation and high switching speed
Source: Today's Electronics Manufacturers: Agilent Technologies, Inc.   Product Description:The operating frequencies of these two FET single-pole double-throw (SPDT) solid-state switches U9397A and U...
fighting Analog electronics
Serial port test method
Now the company has made a development board, and wants to test the serial port. What method should I use? The method I use now is to continuously send and receive data from the serial port....
beijilang5 Embedded System
How do you control the power switch of external devices through software?
I often see such equipment, where the main control software collects the working parameters of the equipment, and then can alarm according to certain limit values. When a certain limit value is reache...
yesoul Embedded System
Since AD9851 can be used instead of AD9854,
[i=s]This post was last edited by paulhyde on 2014-9-15 03:35[/i] The AD9850 can replace the AD9851, so can we use the AD9850? I heard that if we want to make orthogonal, two AD9851s can be used, so c...
电子无聊大神 Electronics Design Contest
[Repost] A brief analysis of the causes of LED driver failure
Basically, the main function of the LED driver is to convert the input AC voltage source into a current source whose output voltage can change with the LED Vf (forward voltage drop). As a key componen...
皇华Ameya360 Power technology
How to input the tbl file generated by QUARTUS simulation into MATLAB for drawing?
I am working on a DDC recently. The tbl file generated by the simulation in QUARTUS is a hexadecimal number. How can I read the data in matlab? Please give me some advice....
zhenpeng25 FPGA/CPLD

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 547  1905  1722  1514  232  12  39  35  31  5 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号