The properly and electrostatically measured taping materials are used for the components, but attention should be paid to the fact that there is some danger the parts absorb on the top
tapes to cause a failure in the mounting and the parts are destructed by static electricity (more than 1kV : 1J, 2A, 2B, 2E 0.5kV : 1E, Human Body Model 100pF 1.5kΩ) to change the
resistance in the conditions of an excessive dryness or after the parts are given vibration for a long time as they are packaged on the tapes. Similarly, care should be given not to apply the
excessive static electricity when mounting on the boards.
●
Ionic impurities such as flux etc. that are attached to these products or those mounted onto a PCB, negatively affect their moisture resistance, corrosion resistance, etc. The flux may
contain ionic substances like chlorine, acid, etc. while perspiration and saliva include ionic impurities like sodium (Na
＋
), chrorine (Cl
−
) etc. Therefore these kinds of ionic substances may
induce electrical corrosion when they invade into the products. Either thorough washing or using RMA solder and flux are necessary since lead free solder contains ionic substances.
Washing process is needed, before putting on moisture proof material in order to prevent electrical corrosion.
●
Please pay attention that the top of an iron does not direct touch to the components. There is a risk that may cause a change in resistance. Take care that another risk may happen that
the protecting coat is carbonized in an instant when touched directly by the top of the iron, also climatic-proof for electric corrosion or insulation of protecting coat may be dropped down.
Be sure not to give high temperature on the top of the iron as it will degrade the protecting coat.
●
Avoid storing components under direct sun rays, high temperature/humidity. Direct sun rays will cause quality change of taping and difficulty of keeping appropriate peeling strength. 5∼
35℃/35∼75%RH, there is no deterioration of solderability for 12 months, but take special care for storing, because condensation, dust, and toxic gas like hydrogen sulfide, sulfurous acid
gas, hydrogen chloride, etc. may drop solderability.
12 3 4567 8910
Month DayThe relevant information and requirements of the fully enclosed electronic design competition:
[i=s]This post was last edited by paulhyde on 2014-9-15 08:58[/i] Wow, this is gr...
Hello, fellow experts; I would like to ask, the value stored in PxIN = the entered value ex: I sent 0x55 from the terminal, but the value displayed by PxIN is 0x13. Did I make a mistake somewhere? I s...
As the title says, when posting, there are often multiple attachments or pictures, but you can only add them one by one repeatedly, so it is strongly recommended to add the batch adding and uploading ...
Dong Yang, executive vice president of the China Association of Automobile Manufacturers, said on the 26th that according to the authorization of the Ministry of Industry and Information Technology...[Details]
1. Problem When developing STM32 with IAR, I found that I could not print floating point numbers by redirecting printf to the serial port. The code is as follows: The output is as follows: It can...[Details]
1. About FPU transplantation As long as the chip has FPU function, the use of FPU is generally enabled by default. You can also select it in the Options tab; 2. About the transplantation of DSP li...[Details]
Function List and Notes (lower-level driver part) 1. IO port initialization: control IO and communication IO. Control includes power control, reset and low power mode. Communication is the serial po...[Details]
After studying the F4 FSMC method to drive the touch screen for a few days, I have gained some understanding, which are listed below. The unorganized record is only for my own reference in the future...[Details]
The Wassenaar Arrangement, everything started during the Cold War. Let's learn more about it with the embedded editor.
background
After the end of World War II, the United States ...[Details]
Autonomous driving
and
5G
are the two hot topics that global companies and media are paying the most attention to, and the combination of the two is the focus of everyone's attention....[Details]
What is SYSTICK: This is a 24-bit system tick timer, SysTick, with automatic reload and overflow interrupt functions. All microcontrollers based on the Cortex_M3 processor can obtain a certain time ...[Details]
This paper proposes a design scheme for an embedded CNC system based on ARM and FPGA. The software and hardware design of the ARM system, the implementation method of hardware fine interpolation ...[Details]
In order to strengthen the traceability management of recycling and utilization of power batteries for new energy vehicles, and to standardize and guide all relevant parties to fulfill their tracea...[Details]
Site conditions: 1. AD acquisition, DMA transmission; AD is set to single-channel continuous mode, DMA is set to single-shot mode. The upper threshold of the AD analog watchdog setting is less than t...[Details]
Independent watchdog (IWDG) and low power mode are often used in STM32 development. The watchdog is to detect and solve faults caused by software errors, and the low power mode is to enter sleep mode...[Details]
Today I am using the AD function of the stm8s microcontroller. There are ten channels from AN0 to AN9 on the microcontroller. I want to use only three of them, AN5 to AN7. //ADC initialization void A...[Details]
Electronics Design Contest
京公网安备 11010802033920号
EEWORLD
