EXPOSED PAD (PIN 17) IS GND, MUST BE SOLDERED TO PCB
UD PACKAGE
16-LEAD (3mm
×
3mm) PLASTIC QFN
T
JMAX
= 125°C,
θ
JA
= 68°C/W,
θ
JC
= 4.2°C/W
EXPOSED PAD (PIN 17) IS GND, MUST BE SOLDERED TO PCB
orDer inForMaTion
LEAD FREE FINISH
LTC3851AEMSE-1#PBF
LTC3851AIMSE-1#PBF
LTC3851AHMSE-1#PBF
LTC3851AMPMSE-1#PBF
LTC3851AEUD-1#PBF
LTC3851AIUD-1#PBF
TAPE AND REEL
LTC3851AEMSE-1#TRPBF
LTC3851AIMSE-1#TRPBF
LTC3851AHMSE-1#TRPBF
LTC3851AMPMSE-1#TRPBF
LTC3851AEUD-1#TRPBF
LTC3851AIUD-1#TRPBF
PART MARKING*
3851A1
3851A1
3851A1
3851A1
LFQB
LFQB
PACKAGE DESCRIPTION
16-Lead Plastic MSOP
16-Lead Plastic MSOP
16-Lead Plastic MSOP
16-Lead Plastic MSOP
16-Lead (3mm
×
3mm) Plastic QFN
16-Lead (3mm
×
3mm) Plastic QFN
TEMPERATURE RANGE
–40°C to 125°C
–40°C to 125°C
–40°C to 150°C
–55°C to 150°C
–40°C to 125°C
–40°C to 125°C
Consult LTC Marketing for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container.
Consult LTC Marketing for information on non-standard lead based finish parts.
For more information on lead free part marking, go to:
http://www.linear.com/leadfree/
For more information on tape and reel specifications, go to:
http://www.linear.com/tapeandreel/
TG
TOP VIEW
3851a1fa
2
LTC3851A-1
elecTrical characTerisTics
SYMBOL
V
IN
V
FB
PARAMETER
Input Operating Voltage Range
Regulated Feedback Voltage
I
TH
= 1.2V (Note 4) 0°C to 85°C
I
TH
= 1.2V (Note 4) –40°C to 125°C
I
TH
= 1.2V (Note 4) –40°C to 150°C
I
TH
= 1.2V (Note 4) –55°C to 150°C
(Note 4)
V
IN
= 6V to 38V (Note 4)
(Note 4) Measured in Servo Loop,
∆I
TH
= 1.2V to 0.7V
(Note 4) Measured in Servo Loop,
∆I
TH
= 1.2V to 0.7V (H-Grade, MP-Grade)
(Note 4) Measured in Servo Loop,
∆I
TH
= 1.2V to 1.6V
(Note 4) Measured in Servo Loop,
∆I
TH
= 1.2V to 1.6V (H-Grade, MP-Grade)
g
m
g
m
GBW
I
Q
UVLO
UVLO Hys
I
SENSE
I
TK/SS
V
RUN
V
RUNHYS
V
SENSE(MAX)
TG R
UP
TG R
DOWN
BG R
UP
BG R
DOWN
TG t
r
TG t
f
BG tr
BG tf
TG/BG t
1D
BG/TG t
2D
t
ON(MIN)
V
INTVCC
V
LDO
INT
Transconductance Amplifier g
m
Transconductance Amp Gain Bandwidth
Input DC Supply Current
Normal Mode
Shutdown
Undervoltage Lockout on INTV
CC
UVLO Hysteresis
SENSE Pins Current
Soft-Start Charge Current
RUN Pin On—Threshold
RUN Pin On—Hysteresis
Maximum Current Sense Threshold
TG Driver Pull-Up On-Resistance
TG Driver Pull-Down On-Resistance
BG Driver Pull-Up On-Resistance
BG Driver Pull-Down On-Resistance
TG Transition Time
Rise Time
Fall Time
BG Transition Time
Rise Time
Fall Time
Top Gate Off to Bottom Gate On Delay
Bottom Switch-On Delay Time
Bottom Gate Off to Top Gate On Delay
Top Switch-On Delay Time
Minimum On-Time
Internal V
CC
Voltage
INTV
CC
Load Regulation
V
FB
= 0.7V, V
SENSE
= 3.3V
V
FB
= 0.7V, V
SENSE
= 3.3V (H-Grade, MP-Grade)
TG High
TG Low
BG High
BG Low
(Note 6)
C
LOAD
= 3300pF
C
LOAD
= 3300pF
(Note 6)
C
LOAD
= 3300pF
C
LOAD
= 3300pF
C
LOAD
= 3300pF Each Driver
(Note 6)
C
LOAD
= 3300pF Each Driver
(Note 6)
(Note 7)
6V < V
IN
< 38V
I
CC
= 0mA to 50mA
4.8
l
l
l
l
l
l
l
l
l
l
The
l
denotes the specifications which apply over the specified operating
junction temperature range, otherwise specifications are at T
A
= 25°C (Note 2). V
IN
= 15V, V
RUN
= 5V unless otherwise noted.
CONDITIONS
MIN
4
0.792
0.788
0.788
0.788
0.800
TYP
MAX
38
0.808
0.812
0.812
0.812
–50
0.02
0.1
0.2
–0.01
–0.1
–0.2
2
3
1
25
3.25
0.4
±1
V
TK/SS
= 0V
V
RUN
Rising
l
UNITS
V
V
V
V
V
nA
%/V
%
%
%
%
mmho
MHz
mA
µA
V
V
Main Control Loops
I
FB
V
REFLNREG
V
LOADREG
Feedback Current
Reference Voltage Line Regulation
Output Voltage Load Regulation
–10
0.002
0.01
I
TH
= 1.2V, Sink/Source = 5µA (Note 4)
I
TH
= 1.2V (Note 8)
(Note 5)
V
RUN
= 5V
V
RUN
= 0V
V
INTVCC
Ramping Down
50
±2
2
1.35
65
70
µA
µA
V
mV
mV
mV
Ω
Ω
Ω
Ω
ns
ns
ns
ns
ns
ns
ns
0.6
1.10
40
35
1
1.22
120
53
2.2
1.2
2.1
1.1
25
25
25
25
30
30
90
5
0.5
INTV
CC
Linear Regulator
5.2
V
%
3851a1fa
3
LTC3851A-1
elecTrical characTerisTics
SYMBOL
f
NOM
f
LOW
f
HIGH
R
MODE/PLLIN
f
MODE
I
FREQ
PGOOD Output
V
PGL
I
PGOOD
V
PG
PGOOD Voltage Low
PGOOD Leakage Current
PGOOD Trip Level
I
PGOOD
= 2mA
V
PGOOD
= 5V
V
FB
with Respect to Set Regulated Voltage
V
FB
Ramping Negative (UV)
V
FB
Ramping Positive (OV)
–12.5
7.5
–10
10
0.1
0.3
±1
–7.5
12.5
V
µA
%
%
PARAMETER
Nominal Frequency
Lowest Frequency
Highest Frequency
MODE/PLLIN Input Resistance
MODE/PLLIN Minimum Input Frequency V
MODE
= External Clock
MODE/PLLIN Maximum Input Frequency V
MODE
= External Clock
Phase Detector Output Current
Sinking Capability
Sourcing Capability
f
MODE
> f
OSC
f
MODE
< f
OSC
Oscillator and Phase-Locked Loop
R
FREQ
= 60k
R
FREQ
= 160k
R
FREQ
= 36k
460
205
690
500
235
750
100
250
750
–90
75
540
265
810
kHz
kHz
kHz
kΩ
kHz
kHz
µA
µA
The
l
denotes the specifications which apply over the specified operating
junction temperature range, otherwise specifications are at T
A
= 25°C (Note 2). V
IN
= 15V, V
RUN
= 5V unless otherwise noted.
CONDITIONS
MIN
TYP
MAX
UNITS
Note 1:
Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime.
Note 2:
The LTC3851A-1 is tested under pulsed load conditions such that
T
A
≈ T
J
. The LTC3851AE-1 is guaranteed to meet performance
specifications from 0°C to 85°C junction temperature. Specifications over
the –40°C to 125°C operating junction temperature range are assured by
design, characterization and correlation with statistical process controls.
The LTC3851AI-1 is guaranteed to meet specifications over the –40°C
to 125°C operating junction temperature range, the LTC3851AH-1 is
guaranteed over the –40°C to 150°C operating junction temperature range
and the LTC3851AMP-1 is tested and guaranteed over the –55°C to 150°C
operating junction temperature range. High junction temperatures degrade
operating lifetimes; operating lifetime is derated for junction temperatures
greater than 125°C. Note that the maximum ambient temperature
consistent with these specifications is determined by specific operating
conditions in conjunction with board layout, the rated package thermal
impedance and other environmental factors.
Note 3:
T
J
is calculated from the ambient temperature T
A
and power
dissipation P
D
according to the following formulas:
LTC3851AMSE-1: T
J
= T
A
+ (P
D
• 40°C/W)
LTC3851AUD-1: T
J
= T
A
+ (P
D
• 68°C/W)
Note 4:
The LTC3851A-1 is tested in a feedback loop that servos V
ITH
to a
specified voltage and measures the resultant V
FB
.
Note 5:
Dynamic supply current is higher due to the gate charge being
delivered at the switching frequency. See Applications Information.
Note 6:
Rise and fall times are measured using 10% and 90% levels. Delay
times are measured using 50% levels. Rise and fall times are assured by
design, characterization and correlation with statistical process controls.
Note 7:
The minimum on-time condition is specified for an inductor
peak-to-peak ripple current ~40% of I
MAX
(see Minimum On-Time
Considerations in the Applications Information section).
The SDH-based MSTP multi-service transmission platform adds Ethernet and ATM service access and processing capabilities to traditional SDH equipment, which can effectively support packet data services...
As people's living standards improve, cars have gradually entered ordinary families, and the number of cars in major cities in China has increased year by year. At the same time, car theft and robbery...
I am a newbie who has just switched to WIN CE for development. I want to develop a ril mdd for cdma based on ril under cellcore. I tried to compile ril and found it is a lib file. How can I get the dl...
I only have the official template program here, no source code, and I haven't been in contact with stm32 for a long time, so I can't understand it. Please help me....
Hello everyone, I encountered some trouble when using jrtplib. I wrote a simple program according to the jrtplib document to initialize jrtplib, int error = 0; RTPSessionParams sessParams; sessParams....
Today's security industry has entered the era of massive networking. Many enterprises, especially financial institutions, have established multi-level video surveillance networking platforms. Lever...[Details]
Capable of providing precise and efficient thermal management for artificial intelligence computing power, intelligent sensing and autonomous driving systems
Shenzhen, ...[Details]
For healthcare professionals, accurate diagnosis and treatment are crucial for a clear picture of a person's health. However, healthcare professionals often rely on tests at medical facilities, cli...[Details]
Gross profit margin jumped from 13.6% in the first half of last year to 25.9%, almost doubling year-on-year.
On August 21, RoboSense released its interim performance report, in which the...[Details]
On August 22, South Korean media Nate reported on the 20th local time that Samsung Electronics is introducing Hyper Cell technology into its most advanced 2nm process technology, striving to improv...[Details]
The automotive industry in 2025 is undergoing a thorough intelligent reshuffle.
Geely wants to make changes in the field of AI cockpits: in the future, there will be no traditional smart...[Details]
With the continuous development of the industrial automation industry, we are seeing an increasing number of intelligent devices using flexible, efficient, and precise robotic arms to p...[Details]
PowiGaN achieves 95% efficiency at both light and full loads, meeting critical operational and safety requirements.
DARWIN, Australia and SAN JOSE, Calif.,
August 22, 2025 – Powe...[Details]
"We have successfully launched the first version of our dedicated chip for EMB brake-by-wire. Second-generation samples have also been successfully completed, and we are actively planning a third-g...[Details]
Electric vehicles will revolutionize transportation, changing fuel consumption, carbon emissions, costs, maintenance, and driving habits. Currently, a major selling point for electric vehicles is t...[Details]
The composition of the water heater
The water heater itself is divided into the following parts:
1. Water tank.
This is where the water heater is filled with water and where the wate...[Details]
introduction
With the development of society, people's requirements for the quality of refrigerated and frozen foods are constantly improving. The changes in food appearance and nutritional co...[Details]
Facial recognition, a biometric technology that uses facial features to authenticate identity, has rapidly become a global market hotspot in recent years as the technology has entered practical use...[Details]
In camera and display systems, the demand for high-performance and low-power data interfaces is driving continuous technological evolution. The evolution of MIPI D-PHY and MIPI C-PHY clearly ...[Details]
Most cameras on the market use chips manufactured by Japanese companies like Sony, Sharp, Panasonic, and LG. South Korea now has the capability to produce chips, but the quality is somewhat inferio...[Details]
RF/Wirelessly
京公网安备 11010802033920号
EEWORLD
