EEWORLDEEWORLDEEWORLD

Part Number

Search

DC1882A

Description
eval board inverting reg ltc3261
CategoryDevelopment board/suite/development tools   
File Size205KB,6 Pages
ManufacturerLinear ( ADI )
Websitehttp://www.analog.com/cn/index.html
Environmental Compliance  
Download Datasheet View All

DC1882A Online Shopping

Suppliers Part Number Price MOQ In stock  
DC1882A - - View Buy Now

DC1882A Overview

eval board inverting reg ltc3261

DEMO MANUAL DC1882A
LTC3261EMSE
High Voltage, Low Noise
Inverting Charge Pump
DESCRIPTION
Demonstration circuit 1882A is a high voltage invert-
ing charge pump featuring the LTC
®
3261EMSE. The
LTC3261 operates with an input voltage from 4.5V to 32V.
The demo board provides the means to select between
Burst Mode
®
operation or constant-frequency mode
operation, plus select an operating frequency of 500kHz,
200kHz, and 50kHz.
The LTC3261 data sheet gives a complete description of
the device, operation and application information. The
data sheet must be read in conjunction with this quick
start guide for demo circuit 1882A.
Design files for this circuit board are available at
http://www.linear.com/demo
L,
LT, LTC, LTM, Linear Technology, the Linear logo and Burst Mode are registered trademarks
of Linear Technology Corporation. All other trademarks are the property of their respective
owners.
PERFORMANCE SUMMARY
SYMBOL
V
IN
V
OUT
PARAMETER
Input Voltage
Output Voltage
Specifications are at T
A
= 25°C
CONDITIONS
MODE = 0V
MODE ≥ 2V
MIN
4.5
–V
IN
–0.94 • V
IN
TYP
MAX
32
UNITS
V
V
V
QUICK START PROCEDURE
Refer to Figure 1 for the proper measurement equipment
setup and jumper settings, and follow the procedure
below.
NOTE: When measuring the input or output voltage ripple,
care must be taken to avoid a long ground lead on the
oscilloscope probe. Measure the input or output voltage
ripple by touching the probe tip directly across the V
IN
or
V
OUT
and GND terminals. See Figure 2 for proper scope
probe technique.
1. Make sure the jumper settings are as follows:
JP1:
EN is in the ON position.
JP2:
MODE is in the BURST position.
JP3:
FREQ is in the 500kHz position.
2. Set PS1 to 15V and turn on supply.
3. Slowly increase the load from 0mA to –100mA and
observe the output voltage and output ripple.
4. Set the load to 0mA.
5. Move the MODE jumper, JP2, from the BURST position
to the CONT FREQ position and then repeat step 3.
6. Set the load to 0mA.
7. Move the FREQ jumper, JP3, from the 500kHz position
to the 200kHz position.
8. Slowly increase the load from 0mA to –50mA and
observe the output voltage and output ripple.
9. Set the load to 0mA.
dc1882afa
1
Regarding the problem of PCB self-loop interference, please help analyze it! ! ! !
As shown in the figure, if I connect the four pins together, and the signal flows through this line, will there be bad interference? Or if this line is VCC or GND, will there be interference?...
放开那个鸡腿 Analog electronics
Big Watermelon FPGA--Advanced FPGA Design--Design Skills
[align=left]FPGA design skills are one of the essential skills for FPGA design, especially for complex logic design. You must make good use of design skills when doing FPGA design. Design skills can m...
王WJR FPGA/CPLD
RT Thread IPC Summary
[size=4][color=#000000][backcolor=white]1. Disabling interrupts can achieve mutual exclusion, but interrupts cannot be responded to at this time[/backcolor][/color][/size] [size=4][color=#000000][back...
Jacktang Microcontroller MCU
The Arduino YúN development board, which is smaller than a credit card, is waiting for you to test!
The development board for everyone to apply for evaluation this time is sponsored by [/color][/size][/font][color=#000] Yunhan Core City [/color][color=black] ([/color][color=black]ICkey[/color][color...
eric_wang Robotics Development
Offline voice control solution
What are the mature offline voice control products on the market that are very practical? Please give me some advice...
AI离线语音控制 51mcu
Re: Ask a serial port question
Today I debugged a serial port program. The host computer used a serial port debugging assistant. The processor on the circuit board is arm7. What the application in arm7 does is: receive serial port ...
chengj Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2777  1814  670  2493  1300  56  37  14  51  27 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号