Resistor values are typically 120 to 240 ohms for 3.3V operation and 82 to 120 ohms for 2.5V
operation.
Figure 7 - Pull Up Pull Down Termination
Resistor values are typically for 3.3V operation
For 2.5V operation, the resistor to ground is 62 ohms and the resistor to supply is 240 ohms
There are numerous application notes on terminating and interfacing PECL logic and the two most common methods are a single resistor to ground, Figure 6,
and a pull-up/pull-down scheme as shown in Figure 7. An AC coupling capacitor is optional, depending on the application and the input logic requirements of
the next stage.
One of the most important considerations is terminating the Output and Complementary Outputs equally. An unused output should not be left un-
terminated, and if one of the two outputs is left open it will result in excessive jitter on both. PC board layout must take this and 50 ohm impedance matching
into account. Load matching and power supply noise are the main contributors to jitter related problems.
LVDS Application Diagrams
+3.3V
OE or NC
10nF
1nF
1
6
Receiver
100
3
4
+3.3V
OE or NC
10nF
1nF
1
6
10nF
100
3
4
Receiver
OE or NC
2
5
OE or NC
2
5
10nF
Figure 8 - LVDS to LVDS, internal 100Ω
Some LVDS structures have an internal 100 ohm resistor on the
input and do not need additional components.
Figure 9 - LVDS to LVDS, External 100Ω and AC block ing caps
One of the most important considerations is terminating the Output and Complementary Outputs equally. An unused output should not be left un-
terminated, and if one of the two outputs is left open it will result in excessive jitter on both. PC board layout must take this and 50 ohm impedance matching
into account. Load matching and power supply noise are the main contributors to jitter related problems.
[i=s] This post was last edited by paulhyde on 2014-9-15 03:05 [/i] A power supply that can output positive and negative 12 volts and positive and negative 5 volts. I made this circuit myself....
Help meRequirements: Use 51 single chip microcomputer and dac0832 to design square wave, sawtooth wave, triangle wave, trapezoidal wave, and the waveform polarity period is variableRequest code schema...
Why is the lower arm PNP transistor of the H-bridge push-pull circuit often damaged, and the three legs of the transistor are directly short-circuited?...
Altera's FPGA and CPLD structure and performance comparison:Hardware Comparison between FPGA and CPLDComparison of the characteristics of FPGA and CPLD...
As the title says, everyone is welcome to chat.
For example, for commonly used interfaces such as RS485, IIC, SPI, CAN, etc., do you know the common circuit structure and electrical level range, such ...
In the afternoon, they played against Serbia and won 3:0, securing the championship one round ahead of schedule. Thus, the Chinese women's volleyball team completed the feat of winning the world champ...
Do you often have to add brake fluid to your car's brakes? The fact that you need to pump out the brake fluid to make sure there is no gas in the brake fluid line may not be done by the car owner h...[Details]
For a long time, due to the limitation of hardware conditions, the display devices of traditional small handheld devices such as PDA are usually monochrome LCD, and the user interface is very simpl...[Details]
1. What is temperature?
Heat is a type of molecular motion. The hotter an object is, the faster its molecules move. Absolute zero is defined as the temperature at which all molecular motion ...[Details]
With concerns about the growing energy crisis, motor efficiency has become an important and timely topic. This is because motors use 63% to 70% of the electricity produced in the United States and ...[Details]
At present, a large number of cooling tower fans, speed fans and special fans are in use in petroleum, chemical, pharmaceutical, metallurgical and other enterprises. Some fans have no monitoring in...[Details]
Abstract: In order to realize wireless automatic alarm and monitoring of major safety places, based on the basic principle of pyroelectric infrared sensing, a detector for receiving infrared radia...[Details]
The future energy storage hotspot is not coal or iron ore, but lithium. This lightest metal in nature may be the heaviest resource in the future energy landscape. China launched an ambitious electr...[Details]
summary
This article will briefly analyze the success and shortcomings of high-frequency DC-DC switching power supplies in the process of miniaturization (the second basic goal), and propose m...[Details]
0 Introduction
In the design and construction of communication systems,
communication power supply
is called the heart of the communication system. The power supply system will dire...[Details]
Stepper motors, also called steppers, use the principles of electromagnetism to convert electrical energy into mechanical energy and have been used since the 1920s. With the increasing popularity o...[Details]
In the past 20 years, although the inverters that use power transistors (GTR) as inverter power devices, 8-bit microprocessors as control cores, and realize asynchronous motor speed regulation acco...[Details]
(1) Open circuit voltage of the battery
(2) Internal resistance of the battery
(3) Battery operating voltage
(4) Charging voltage
Charging voltage refers to the voltage applied ...[Details]
1 Causes of problems with electric vehicle batteries
1.1 Caused by the battery itself
Why do we say that? In the previous issue, we learned about the working princi...[Details]
Lithium iron phosphate batteries are used as lithium-ion secondary batteries. Their main application is now in power batteries, which have great advantages over NI-H and Ni-Cd batteries.
Lithi...[Details]
With the continuous development of integrated circuit technology, integrated circuits have developed from thousands of gates to the current level of millions and tens of millions of gates. The applica...[Details]
Electronics Design Contest
京公网安备 11010802033920号
EEWORLD
