EEWORLDEEWORLDEEWORLD

Part Number

Search

E8701-A4-2-N-G

Description
Switch, SPDT, Momentary, 1A, 28VDC, Through Hole-right Angle
CategoryMechanical and electronic products    switch   
File Size873KB,4 Pages
ManufacturerSalecom Electronics Co., Ltd.
Download Datasheet Parametric View All

E8701-A4-2-N-G Overview

Switch, SPDT, Momentary, 1A, 28VDC, Through Hole-right Angle

E8701-A4-2-N-G Parametric

Parameter NameAttribute value
Objectid303914439
Reach Compliance Codeunknown
ECCN codeEAR99
Actuator angle
Actuator colorBLACK
Actuator length0.282 inch
Actuator typePUSHBUTTON
Other featuresWITHOUT CAP
body width6.604 mm
body height13.335 mm
Body length or diameter12.7 mm
Casing diameter0.255 inch
Nozzle length0.25 inch
Casing typeUNTHREADED
center contact materialCOPPER ALLOY
Center contact platingGOLD OVER SILVER
Contact (AC) maximum rated R load1A@120VAC
Maximum contact current (AC)1 A
Maximum contact current (DC)1 A
Contact (DC) maximum rated power R load0.4VA@20VDC
Contact (DC) maximum rated R load1A@28VDC
Contact functionON-(ON)
Contact resistance0.02 mΩ
contact timeSNAP ACTION
Maximum contact voltage (AC)120 V
Maximum contact voltage (DC)28 V
Dielectric withstand voltage1000VDC V
Electrical life50000 Cycle(s)
End contact materialCOPPER ALLOY
End contact platingGOLD OVER SILVER
Insulation resistance1000000000 Ω
insulator materialGLASS FILLED NYLON
Installation featuresTHROUGH HOLE-RIGHT ANGLE
Maximum operating temperature85 °C
Minimum operating temperature-30 °C
PCB hole count5
sealEPOXY
surface mountNO
Switch actionMOMENTARY
switch functionSPDT
Terminal surfaceGOLD/NICKEL
Terminal length0.125 inch
Terminal materialCOPPER ALLOY
Termination typeSOLDER
Application of RS485 bus isolation module MRT485DLT in STM32F103VET system
Note: In a low-power system, when entering a low-power state, the MCU's serial port needs to be set to a high-impedance state to avoid unnecessary power consumption caused by leakage current from the ...
伊亓 Industrial Control Electronics
Manchester decoding problem in fiber optic communications.
I made a Manchester decoding module (written in Verilog) at the receiving end of the optical fiber, without any verification algorithm. The bit error rate is very high, basically around 1%. If anyone ...
rica321 Embedded System
The technical life of the new generation of engineers (I)
[font=宋体][size=3]1. Growth - From a rock youth to a design eliteOne day in September, at a technical seminar, Mr. A was looking through the demo board and asking about some technical details, just lik...
gnkjmcu MCU
Op amp integrator circuit help
This circuit inputs a step signal, isn't it a DC signal afterwards? The capacitor does not work, how can Uo=AUi be infinite? Please help me...
迷雾白狐 Analog electronics
Renesas 78K0S development environment installation problem, everyone come in and take a look! !
I am new to using Renesas chips. There are so many softwares to install when developing simulations. And there is a problem. There is little information online. Has anyone encountered the same problem...
victor_z Renesas Electronics MCUs
Develop an FPGA development board
[i=s]This post was last edited by 2638823746 on 2014-6-11 11:19[/i] I have a Zedboad development board, basically brand new, with the packaging, all accessories, and CD, basically brand new. If you ne...
2638823746 Buy&Sell

Technical ResourceMore

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 617  2749  1153  1786  2594  13  56  24  36  53 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号