EEWORLDEEWORLDEEWORLD

Part Number

Search

DIP1989SD001402DA

Description
Array/Network Resistor, Isolated, 0.2W, 14000ohm, 100V, 0.5% +/-Tol, -300,300ppm/Cel, 7025,
CategoryPassive components    The resistor   
File Size334KB,3 Pages
ManufacturerTT Electronics plc
Websitehttp://www.ttelectronics.com/
Download Datasheet Parametric View All

DIP1989SD001402DA Overview

Array/Network Resistor, Isolated, 0.2W, 14000ohm, 100V, 0.5% +/-Tol, -300,300ppm/Cel, 7025,

DIP1989SD001402DA Parametric

Parameter NameAttribute value
Is it Rohs certified?incompatible
Objectid791721499
Reach Compliance Codecompliant
Country Of OriginUSA
ECCN codeEAR99
YTEOL6.9
structureWelded
JESD-609 codee0
Lead length3.429 mm
lead spacing2.54 mm
Network TypeIsolated
Number of terminals14
Maximum operating temperature150 °C
Minimum operating temperature-55 °C
Package height2.032 mm
Package length17.78 mm
Package formDIP
Package width6.35 mm
Rated power dissipation(P)0.2 W
resistance14000 Ω
Resistor typeARRAY/NETWORK RESISTOR
series1900
size code7025
Temperature Coefficient300 ppm/°C
Terminal surfaceTin/Lead (Sn60Pb40)
Tolerance0.5%
Operating Voltage100 V

DIP1989SD001402DA Preview

TaNFilm Precision DIP Network
Commercial and MIL Qualified
®
1900 Series
·
·
·
·
·
·
Inherent reliability
MIL-PRF-83401 qualified
Custom configuration available
Bonded leads not susceptible to
solder reflow problems
Absolute tolerance to
±0.1% / ratio tolerance to ±0.05%
Absolute TCR to
±15ppm/°C / ratio tracking to ±5ppm/°C
_____
General Note
TT electronics reserves the right to make changes in product specification without notice or liability.
All information is subject to TT electronics’ own data and is considered accurate at time of going to print.
www.bitechnologies.com www.irctt.com www.welwyn-tt.com
© TT electronics plc
09. 11
TaNFilm
®
Precision DIP Network
Commercial and MIL Qualified
1900 Series
General Note
TT electronics reserves the right to make changes in product specification without notice or liability.
All information is subject to TT electronics’ own data and is considered accurate at time of going to print.
www.bitechnologies.com www.irctt.com www.welwyn-tt.com
© TT electronics plc
09. 11
TaNFilm
®
Precision DIP Network
Commercial and MIL Qualified
1900 Series
General Note
TT electronics reserves the right to make changes in product specification without notice or liability.
All information is subject to TT electronics’ own data and is considered accurate at time of going to print.
www.bitechnologies.com www.irctt.com www.welwyn-tt.com
© TT electronics plc
09. 11
Integrated circuit detection method
Editor's note: Although there are ways to replace integrated circuits, disassembly is troublesome after all. Therefore, before disassembly, you should accurately determine whether the integrated circu...
fighting Test/Measurement
Could you please tell me about the drift suppression principle of single-output differential amplifier circuit?
If the two output terminals of the differential amplifier circuit are connected to the collectors of two transistors respectively, then they can effectively suppress drift. However, if it is a single ...
enlwm Analog electronics
Looking for msp430&&nRF24L01 battery powered system
I am working on a wireless data download project based on msp430 and nRF24L01 When powered by a power supply, data downloading is normal.But when it comes to battery powered systems, there are problem...
chhd1128 Microcontroller MCU
wince 5.0 power display
There is no power display on my wince 5.0 development board. How can I implement it? It's so troublesome. I checked some information, but I still have no idea. It says that hardware support is needed,...
ntdx Embedded System
Designing CAN rate converter using visual programming
CAN rate conversion is a common application. For example, to connect a 250Kpbs CAN bus to a 500Kbps bus so that the data can be communicated, rate conversion is required. As shown in the following fig...
如越 Automotive Electronics
When using an oscilloscope probe to measure the AC waveform between the two ends of a component, how should the probe ground wire be connected?
When using an oscilloscope probe to measure the AC waveform between the two ends of a component, if the peak value of the AC voltage of the probe ground wire is 180V and the minimum value is -180V, th...
深圳小花 MCU

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 226  1220  876  970  1948  5  25  18  20  40 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号