EEWORLDEEWORLDEEWORLD

Part Number

Search

FP-8999SD-02-1012-DG

Description
Array/Network Resistor, Isolated, Tantalum Nitride/nickel Chrome, 0.05W, 10100ohm, 50V, 0.5% +/-Tol, -50,50ppm/Cel, 3925,
CategoryPassive components    The resistor   
File Size184KB,4 Pages
ManufacturerTT Electronics plc
Websitehttp://www.ttelectronics.com/
Download Datasheet Parametric View All

FP-8999SD-02-1012-DG Overview

Array/Network Resistor, Isolated, Tantalum Nitride/nickel Chrome, 0.05W, 10100ohm, 50V, 0.5% +/-Tol, -50,50ppm/Cel, 3925,

FP-8999SD-02-1012-DG Parametric

Parameter NameAttribute value
Is it Rohs certified?incompatible
Objectid794801999
Reach Compliance Codecompliant
Country Of OriginUSA
YTEOL7.15
structureFlatpack
Network TypeIsolated
Number of terminals16
Maximum operating temperature125 °C
Minimum operating temperature-65 °C
Package height1.905 mm
Package length9.906 mm
Package formSMT
Package width6.35 mm
Rated power dissipation(P)0.05 W
resistance10100 Ω
Resistor typeARRAY/NETWORK RESISTOR
seriesFP
size code3925
technologyTANTALUM NITRIDE/NICKEL CHROME
Temperature Coefficient50 ppm/°C
Tolerance0.5%
Operating Voltage50 V
TaNFilm
®
Precision
Flat Pack Networks
8900 Series
Precision absolute and ratio tolerances available
Qualified to MIL-R-83401 /03, /10 and /15
Qualified to characteristics M, K and H
Custom schematics readily available
Absolute TCR to ±15ppm/°C
TaNFilm
®
resistor networks are designed for use in applications requiring a high degree of reliability, stability, tight
tolerance and TCR tracking, and low noise. The sputtering process for resistor formation has been perfected to allow a
continuous feed production line under high vacuum conditions, thus, insuring uniformity of properties between networks.
Laser trimming makes tight ratios easily achievable. The gold plated copper leads are solid phase welded to a large
area of gold conductor pads on the ceramic substrate assuring the most reliable termination and long term stability.
The Tantalum Nitride resistor material is passivated for environmental protection insuring excellent performance far
superior to military requirements.
Our TaNFilm
®
process enables us to manufacture networks containing different resistance values and still maintain tight
tolerances and tracking characteristics. The nature of our photo-etch process makes it readily adaptable to meet each
individual customer’s needs. Custom circuit designs and special mechanical configurations can be easily achieved
with a modest set up charge while maintaining our high standards of precision and reliability.
Electrical Data
Schematic
Resistance
Range
(Ω)
10 - 49.9
50.0 - 199
Absolute
Tolerance
F, G, J
F, G, J
B, D, F, G, J
B, D, F, G, J
B, D, F, G, J
B, D, F, G, J
B, D, F, G, J
B, D, F, G, J
B, D, F, G, J
Optional
Ratio
Tolerance
F, G
D, F, G
A, B, D, F, G
T, Q, A, B, D, F, G
A, B, D, F, G
B, D, F, G
B, D, F, G
B, D, F, G
B, D, F, G
Absolute TCR
(ppm/°C)
±50; ±100; ±300
±25; ±50; ±100; ±300
±25; ±50; ±100; ±300
±15; ±25; ±50; ±100; ±300
±25; ±50; ±100; ±300
±300; ±100
±300; ±100; ±50
±25; ±50; ±100; ±300
±15; ±25; ±50; ±100; ±300
Tracking
TCR
(ppm/°C)
±20
±10
±5
±5
±5
±50
±20
Element
Power
(mW)
A
200 - 999
1.0K - 100K
101K - 200K
50 - 149
150 - 499
50
B
500 - 999
1.0K - 150K
±5
±5
25
General Note
IRC reserves the right to make changes in product specification without notice or liability.
All information is subject to IRC’s own data and is considered accurate at time of going to print.
A subsidiary of
TT electronics plc
8900 Series Issue September 2009 Sheet 1 of 4
© IRC Advanced Film Division
• 4222 South Staples Street • Corpus Christi Texas 78411 USA
Telephone: 361 992 7900 • Facsimile: 361 992 3377 • Website: www.irctt.com
ADC conversion method and main parameters
ADCADC is the English abbreviation of analog-to-digital converter, which is an electronic component that can convert analog signals into digital signals. Usually, the signal is sampled and held, and t...
Jacktang Analogue and Mixed Signal
Help, I want to do an AD conversion and then interrupt
Specifically, a voltage signal is input from the outside, and then converted to a digital value through AD. I want to compare it with the preset value. If it is higher than the preset value, it will b...
sherry32 DSP and ARM Processors
Dynamic detection of mobile networks
Dynamic detection of TD-SCDMA network The product we developed uses TD module. When the network signal is good, it should be fine to use it normally. When the network signal is not good (no network), ...
tianjixian Embedded System
About the program of simulating and receiving pulse signals with CCS in DSP
Help~~~~~~I used to work with single-chip microcomputers, but now I need to use DSP to receive the signal from a light spot encoder. I can only find QEP circuits on the Internet, but it doesn't explai...
wk8272085 DSP and ARM Processors
Introduction to Commonly Used Operational Amplifier Models
Introduction to Common Operational Amplifier Models.pdf...
luopi2000 Analog electronics
How to measure wind and no wind
To measure wind in the research and development instrument, we only need to measure whether there is wind passing through the pipe. The working condition is to measure whether there is wind passing th...
DSP16 Test/Measurement

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2765  1392  1767  2883  616  56  29  36  59  13 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号