5962R0252301Q9A datasheet, PDF

Datasheet> All Categories > The embedded processor and controller> Microcontrollers and processors> 5962R0252301Q9A

5962R0252301Q9A: DescriptionMicrocontroller, 16-Bit, 8096 CPU, 20MHz, CMOS, DIE-218; CategoryThe embedded processor and controller Microcontrollers and processors; File Size230KB，42 Pages; ManufacturerCobham PLC

Download Datasheet Parametric View All

5962R0252301Q9A Overview

Microcontroller, 16-Bit, 8096 CPU, 20MHz, CMOS, DIE-218

5962R0252301Q9A Parametric

Parameter Name	Attribute value
Objectid	8005875667
package instruction	DIE, DIE OR CHIP
Reach Compliance Code	unknown
ECCN code	3A001.A.2.C
Has ADC	NO
Address bus width	16
bit size	16
CPU series	8096
maximum clock frequency	20 MHz
DAC channel	NO
DMA channel	NO
External data bus width	16
JESD-30 code	X-XUUC-N218
Number of I/O lines	24
Number of terminals	218
Maximum operating temperature	125 °C
Minimum operating temperature	-55 °C
PWM channel	YES
Package body material	UNSPECIFIED
encapsulated code	DIE
Encapsulate equivalent code	DIE OR CHIP
Package shape	UNSPECIFIED
Package form	UNCASED CHIP
Certification status	Not Qualified
RAM (bytes)	1000
Filter level	MIL-PRF-38535 Class Q
speed	20 MHz
Maximum supply voltage	5.5 V
Minimum supply voltage	4.5 V
Nominal supply voltage	5 V
surface mount	YES
technology	CMOS
Temperature level	MILITARY
Terminal form	NO LEAD
Terminal location	UPPER
total dose	300k Rad(Si) V
uPs/uCs/peripheral integrated circuit type	MICROCONTROLLER

Preview

Download Datasheet

View All

REVISIONS

LTR

DESCRIPTION

Update boilerplate to current MIL-PRF-38535 requirements. - CFS

Add device types -03 and -04. Reduce the RHA Total Dose from 300krads to

100krads for device types 01 and 02. - CFS

DATE (YR-MO-DA)

07-05-14

08-12-01

APPROVED

Thomas M. Hess

REV

SHEET

REV

SHEET

REV STATUS

OF SHEETS

PMIC N/A

REV

SHEET

PREPARED BY

Larry T. Gauder

STANDARD

MICROCIRCUIT

DRAWING

THIS DRAWING IS AVAILABLE

FOR USE BY ALL

DEPARTMENTS

AND AGENCIES OF THE

DEPARTMENT OF DEFENSE

CHECKED BY

Charles F. Saffle

APPROVED BY

Thomas M. Hess

DRAWING APPROVAL DATE

02-09-26

DEFENSE SUPPLY CENTER COLUMBUS

COLUMBUS, OHIO 43218-3990

http://www.dscc.dla.mil

MICROCIRCUIT, DIGITAL, CMOS, RADIATION

HARDENED, MCS-96 BASED

MICROCONTROLLER, MONOLITHIC SILICON

AMSC N/A

REVISION LEVEL

SIZE

CAGE CODE

67268

1 OF

5962-02523

DSCC FORM 2233

APR 97

SHEET

5962-E310-08

2. APPLICABLE DOCUMENTS

2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part

of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the

solicitation or contract.

DEPARTMENT OF DEFENSE SPECIFICATION

MIL-PRF-38535

Integrated Circuits, Manufacturing, General Specification for.

DEPARTMENT OF DEFENSE STANDARDS

MIL-STD-883

MIL-STD-1835

Test Method Standard Microcircuits.

Interface Standard Electronic Component Case Outlines.

DEPARTMENT OF DEFENSE HANDBOOKS

MIL-HDBK-103

MIL-HDBK-780

List of Standard Microcircuit Drawings.

Standard Microcircuit Drawings.

(Copies of these documents are available online at

http://assist.daps.dla.mil/quicksearch/

http://assist.daps.dla.mil

or from

the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.)

2.2 Non-government publications. The following document(s) form a part of this document to the extent specified herein.

Unless otherwise specified, the issues of the documents are the issues of the documents cited in the solicitation or contract.

AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM)

ASTM F1192

Standard Guide for the Measurement of Single Event Phenomena (SEP) Induced by Heavy Ion

Irradiation of Semiconductor Devices.

(Copies of these documents are available online at

http://www.astm.org

or from ASTM International, 100 Barr Harbor Drive,

P.O. Box C700, West Conshohocken, PA 19428-2959.)

2.3 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of

this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a

specific exemption has been obtained.

3. REQUIREMENTS

3.1 Item requirements. The individual item requirements for device classes Q and V shall be in accordance with

MIL-PRF-38535 and as specified herein or as modified in the device manufacturer's Quality Management (QM) plan. The

modification in the QM plan shall not affect the form, fit, or function as described herein. The individual item requirements for

device class M shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified

herein.

3.1.1 Microcircuit die. For the requirements of microcircuit die, see appendix A to this document.

STANDARD

MICROCIRCUIT DRAWING

DEFENSE SUPPLY CENTER COLUMBUS

COLUMBUS, OHIO 43218-3990

DSCC FORM 2234

APR 97

SIZE

REVISION LEVEL

5962-02523

SHEET

3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in

MIL-PRF-38535 and herein for device classes Q and V or MIL-PRF-38535, appendix A and herein for device class M.

3.2.1 Case outline(s). The case outline(s) shall be in accordance with 1.2.4 herein and figure 1.

3.2.2 Terminal connections. The terminal connections shall be as specified on figure 2.

3.2.3 Block diagram. The block diagram shall be as specified on figure 3.

3.2.4 Load circuit and waveforms. The Load circuit and waveforms shall be as specified on figure 4.

3.2.5 Radiation exposure circuit. The radiation exposure circuit shall be maintained by the manufacturer under document

revision level control and shall be made available to the preparing and acquiring activity upon request.

3.3 Electrical performance characteristics and postirradiation parameter limits. Unless otherwise specified herein, the

electrical performance characteristics and postirradiation parameter limits are as specified in table IA and shall apply over the full

case operating temperature range.

3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table IIA. The electrical

tests for each subgroup are defined in table IA.

3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturer's PIN may also be

marked. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer

has the option of not marking the "5962-" on the device. For RHA product using this option, the RHA designator shall still be

marked. Marking for device classes Q and V shall be in accordance with MIL-PRF-38535. Marking for device class M shall be

in accordance with MIL-PRF-38535, appendix A.

3.5.1 Certification/compliance mark. The certification mark for device classes Q and V shall be a "QML" or "Q" as required in

MIL-PRF-38535. The compliance mark for device class M shall be a "C" as required in MIL-PRF-38535, appendix A.

3.6 Certificate of compliance. For device classes Q and V, a certificate of compliance shall be required from a QML-38535

listed manufacturer in order to supply to the requirements of this drawing (see 6.6.1 herein). For device class M, a certificate of

compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see

6.6.2 herein). The certificate of compliance submitted to DSCC-VA prior to listing as an approved source of supply for this

drawing shall affirm that the manufacturer's product meets, for device classes Q and V, the requirements of MIL-PRF-38535 and

herein or for device class M, the requirements of MIL-PRF-38535, appendix A and herein.

3.7 Certificate of conformance. A certificate of conformance as required for device classes Q and V in MIL-PRF-38535 or for

device class M in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing.

3.8 Notification of change for device class M. For device class M, notification to DSCC-VA of change of product (see 6.2

herein) involving devices acquired to this drawing is required for any change that affects this drawing.

3.9 Verification and review for device class M. For device class M, DSCC, DSCC's agent, and the acquiring activity retain the

option to review the manufacturer's facility and applicable required documentation. Offshore documentation shall be made

available onshore at the option of the reviewer.

3.10 Microcircuit group assignment for device class M. Device class M devices covered by this drawing shall be in

microcircuit group number 105 (see MIL-PRF-38535, appendix A).

STANDARD

MICROCIRCUIT DRAWING

DEFENSE SUPPLY CENTER COLUMBUS

COLUMBUS, OHIO 43218-3990

DSCC FORM 2234

APR 97

SIZE

REVISION LEVEL

5962-02523

SHEET

Recommended Resources

Multifunctional dimming desk lamp circuit

High-precision constant current source circuit diagram composed of TL431

One control ten motor starting circuit_1

Temperature sensor to digital MPU connection circuit

Sawtooth wave circuit using transistor as constant current source

Computer motherboard circuit diagram 810 1_28

Ask for solutions for traffic statistics: Please help me with the traffic statistics solution. I would be very grateful....; tulao Embedded System

In WINCE system, only display your own software and hide the taskbar below: How can I show only my own software and hide the taskbar in WINCE? In other words, I only want to see my own software and other things in WINCE cannot be seen by users. How can I deal with this?...; coveyniu Embedded System

About the 6410+WinCE6.0 boot interface logo problem: There are generally two ways to implement the boot logo: Method 1: Pack it in EBOOT.bin as a header file, but this method often makes EBOT.bin too large; Method 2: Convert bmp to bin file, burn it to ...; trason Embedded System

Do you know the common built-in functions and some instructions of MSP430F5529?: MSP430F5529 supports a maximum operating frequency of 25MHZ, which means that there is a limit to the speed of the system through the phase-locked loop multiplication. The maximum speed can only reach...; fish001 Microcontroller MCU

Design case: Design of 4~16V output switching regulated power supply: 1 Introduction In scientific research, production, experiments and other applications, power supplies with voltages of 5 to 15V and currents of 5 to 40A are often used. However, the maximum current of...; qwqwqw2088 Analogue and Mixed Signal

【National Technology N32G430】04 Configure the clock and run the lights: [i=s]This post was last edited by Qintianqintian0303 on 2022-10-3 00:50[/i]04 Configure the clock and run the lights N32G430 clock tree:Configure the clock according to the clock tree information: 1. ...; 秦天qintian0303 Domestic Chip Exchange

Shortcut: E0 E1 E2 E3 E4 E5 E6 E7 E8 E9 EA EB EC ED EE EF EG EH EI EJ EK EL EM EN EO EP EQ ER ES ET EU EV EW EX EY EZ F0 F1 F2 F3 F4 F5 F6 F7 F8 F9 FA FB FC FD FE FF FG FH FI FJ FK FL FM FN FO FP FQ FR FS FT FU FV FW FX FY FZ G0 G1 G2 G3 G4 G5 G6 G7 G8 G9 GA GB GC GD GE GF GG GH GI GJ GK GL GM GN GO GP GQ GR GS GT GU GV GW GX GZ H0 H1 H2 H3 H4 H5 H6 H7 H8 HA HB HC HD HE HF HG HH HI HJ HK HL HM HN HO HP HQ HR HS HT HU HV HW HX HY HZ I1 I2 I3 I4 I5 I6 I7 IA IB IC ID IE IF IG IH II IK IL IM IN IO IP IQ IR IS IT IU IV IW IX J0 J1 J2 J6 J7 JA JB JC JD JE JF JG JH JJ JK JL JM JN JP JQ JR JS JT JV JW JX JZ K0 K1 K2 K3 K4 K5 K6 K7 K8 K9 KA KB KC KD KE KF KG KH KI KJ KK KL KM KN KO KP KQ KR KS KT KU KV KW KX KY KZ

Popular Components