Technical Data Sheet
Multicore Hydro-X
September
2007
HIGH ACTIVITY WATER SOLUBLE CORED
SOLDER WIRE
Properties of Multicore Hydro-X solid flux cored solder
wires:
Rapid soldering of most difficult to solder parts
Fast wetting
Water washable, no need for added neutralisers
No insoluble residues
No spitting
Residues must be removed
PRODUCT RANGE
Multicore Hydro-X cored wires are manufactured with a
flux content of 2%.
Multicore Hydro-X cored wires are available in a variety of
alloys conforming to J-STD-006 and EN 29453 or alloys
conforming to similar national or international standards.
For details refer to document “Properties of Alloys used in
Cored Solder Wires”. A wide range of wire diameters is
available.
APPLICATION
Multicore Hydro-X water soluble flux cored solder wires
are suitable for use in normal hand soldering operations
where the components have been assessed as being able to
withstand the necessary washing procedures.
Stranded wire should not be used. Strip any insulation back
so that flux residues are not trapped during the washing
process.
CLEANING
It is essential that the residues from soldering with
Multicore Hydro-X cored solder wires be removed as soon
as possible after soldering. The residues from Multicore
Hydro-X cored solder wires may be readily cleaned in
conventional equipment using water. It is important that the
cleanliness of boards and components is thoroughly
checked after soldering and cleaning. The usual procedure
is to continuously check the conductivity of the final rinse
water as a measure of ionic contamination. Samples of
cleaned boards should be subjected to a laboratory
corrosion test, insulation resistance test, or ionic
contamination assessment.
RECOMMENDED OPERATING CONDITIONS
Soldering iron:
Good results should be obtained using a
range of tip temperatures. However, the optimum tip
temperature and heat capacity required for a hand soldering
process is a function of both soldering iron design and the
nature of the task and care should be exercised to avoid
unnecessarily high tip temperatures for excessive times. A
high tip temperature will increase any tendency to flux
spitting and it may produce some residue darkening.
The soldering iron tip should be properly tinned and this
may be achieved using Multicore cored wire. Severely
contaminated soldering iron tips should first be cleaned and
pre-tinned using Multicore Tip Tinner/Cleaner, then wiped
on a clean, damp sponge before re-tinning with Multicore
cored wire.
Soldering process:
To achieve the best results from
Multicore solder wires, recommended working practices for
hand soldering should be observed as follows:
Apply the soldering iron tip to the work surface,
ensuring that it simultaneously contacts the base
material and the component termination to heat both
surfaces adequately. This process should only take a
fraction of a second.
Apply Multicore flux cored solder wire to a part of the
joint surface away from the soldering iron and allow to
flow sufficiently to form a sound joint fillet – this
should be virtually instantaneous. Do not apply
excessive solder or heat to the joint as this may result
in dull, gritty fillets and excessive or darkened flux
residues.
Remove solder wire from the work piece and then
remove the iron tip.
The total process will be very rapid, depending upon
thermal mass, tip temperature and configuration and the
solderability of the surfaces to be joined.
Multicore flux cored solder wires provide fast soldering on
copper and brass surfaces as well as solder coated
materials. Activity of the halide activated versions on
nickel is also good depending on the state of oxidation of
the nickel finish. The good thermal stability of Multicore
fluxes means they are also well suited to soldering
applications requiring high melting temperature alloys
NOT FOR PRODUCT SPECIFICATIONS.
THE TECHNICAL INFORMATION CONTAINED HEREIN IS INTENDED FOR REFERENCE ONLY. PLEASE CONTACT HENKEL
TECHNOLOGIES TECHNICAL SERVICE FOR ASSISTANCE AND RECOMMENDATIONS ON SPECIFICATIONS FOR THIS
PRODUCT.
Hydro-X, September 2007
GENERAL INFORMATION
For safe handling information on this product, consult
the Material Safety Data Sheet, (MSDS).
Note
The data contained herein are furnished for information only and are
believed to be reliable. We cannot assume responsibility for the results
obtained by others over whose methods we have no control. It is the user's
responsibility to determine suitability for the user's purpose of any
production methods mentioned herein and to adopt such precautions as
may be advisable for the protection of property and of persons against any
hazards that may be involved in the handling and use thereof. In light of
the foregoing,
Henkel Corporation specifically disclaims all warranties
expressed or implied, including warranties of merchantability or
fitness for a particular purpose, arising from sale or use of Henkel
Corporation’s products. Henkel Corporation specifically disclaims
any liability for consequential or incidental damages of any kind,
including lost profits.
The discussion herein of various processes or
compositions is not to be interpreted as representation that they are free
from domination of patents owned by others or as a license under any
Henkel Corporation patents that may cover such processes or
compositions. We recommend that each prospective user test his proposed
application before repetitive use, using this data as a guide. This product
may be covered by one or more United States or foreign patents or patent
applications.
Americas
Henkel Corporation
15350 Barranca Parkway
Irvine, CA 92618 U.S.A.
949.789.2500
Europe
Henkel Loctite Adhesives Ltd
Technologies House, Wood Lane End
Hemel Hempstead
Hertfordshire HP2 4RQ, United Kingdom
+44 (0) 1442 278 000
Asia
Henkel Loctite (China) Co. Ltd
No. 90 Zhujiang Road
Yantai Development Zone
Shandong, China 264006
+86 535 6399820
All trademarks, except where noted are the property of Henkel Corp.
Embedded System
京公网安备 11010802033920号
EEWORLD
