DIP1989009762FG datasheet, PDF

Datasheet> All Categories > Passive components> The resistor> DIP1989009762FG

DIP1989009762FG: DescriptionArray/Network Resistor, Isolated, 0.2W, 97600ohm, 100V, 1% +/-Tol, -300,300ppm/Cel, 7025,; CategoryPassive components The resistor; File Size334KB，3 Pages; ManufacturerTT Electronics plc; Websitehttp://www.ttelectronics.com/; Environmental Compliance

Download Datasheet Parametric View All

DIP1989009762FG Overview

Array/Network Resistor, Isolated, 0.2W, 97600ohm, 100V, 1% +/-Tol, -300,300ppm/Cel, 7025,

DIP1989009762FG Parametric

Parameter Name	Attribute value
Is it Rohs certified?	conform to
Objectid	791680916
Reach Compliance Code	compliant
Country Of Origin	USA
ECCN code	EAR99
YTEOL	6.8
structure	Welded
JESD-609 code	e4
Lead length	3.429 mm
lead spacing	2.54 mm
Network Type	Isolated
Number of terminals	14
Maximum operating temperature	150 °C
Minimum operating temperature	-55 °C
Package height	2.032 mm
Package length	17.78 mm
Package form	DIP
Package width	6.35 mm
Rated power dissipation(P)	0.2 W
resistance	97600 Ω
Resistor type	ARRAY/NETWORK RESISTOR
series	1900
size code	7025
Temperature Coefficient	300 ppm/°C
Terminal surface	Gold (Au)
Tolerance	1%
Operating Voltage	100 V

DIP1989009762FG Preview

TaNFilm Precision DIP Network

Commercial and MIL Qualified

1900 Series

Inherent reliability

MIL-PRF-83401 qualified

Custom configuration available

Bonded leads not susceptible to

solder reflow problems

Absolute tolerance to

±0.1% / ratio tolerance to ±0.05%

Absolute TCR to

±15ppm/°C / ratio tracking to ±5ppm/°C



√

_____

General Note

TT electronics reserves the right to make changes in product specification without notice or liability.

All information is subject to TT electronics’ own data and is considered accurate at time of going to print.

www.bitechnologies.com www.irctt.com www.welwyn-tt.com

09. 11

TaNFilm

Precision DIP Network

Commercial and MIL Qualified

1900 Series

General Note

TT electronics reserves the right to make changes in product specification without notice or liability.

All information is subject to TT electronics’ own data and is considered accurate at time of going to print.

www.bitechnologies.com www.irctt.com www.welwyn-tt.com

09. 11

TaNFilm

Precision DIP Network

Commercial and MIL Qualified

1900 Series

General Note

TT electronics reserves the right to make changes in product specification without notice or liability.

All information is subject to TT electronics’ own data and is considered accurate at time of going to print.

www.bitechnologies.com www.irctt.com www.welwyn-tt.com

09. 11

More (Only the first 5 pages are displayed. Please Download Datasheet to view the full content.) >

Recommended Resources

Insulation resistance meter circuit diagram

vehicle alarm circuit

CAT (X-ray detection) circuit

Overvoltage protection circuit diagram composed of fuse and thyristor

Basic application circuit diagram of LM2931

bistable circuit

3W Power Holdings/AEG Power Solutions: [i=s]This post was last edited by dontium on 2015-1-23 13:40[/i]3W Power Holdings/AEG Power Solutions: Dr Horst J. Kayser is appointed to the BoardThe shareholders of 3W Power Holdings SA approved the...; 安_然 Analogue and Mixed Signal

[Help] Hi guys, is there a built-in temperature sensor in 430F13X?: [Help] Hi guys, does 430F13X have a built-in temperature sensor?I read the description and it said it does, but I didn't see it in the manual.Is there one?Has anyone used it?If so, can it read the cur...; MARS敏 Microcontroller MCU

STM32 should have a chip with wide pin spacing package: Recently, I have a headache in soldering the chip with 0.5 pin pitch, so I wonder why ST does not release a larger package? Of course, this is wishful thinking. Technology is advancing, and chip techn...; william_lyl stm32/stm8

Hey guys, can I ask what type of shunt do you use in the switching power supplies you make?: Can you guys tell me what type of shunt do you use in your switching power supplies? What brand?...; Locifer Power technology

51+proteus simulation application: [i=s]This post was last edited by paulhyde on 2014-9-15 09:08[/i] :loveliness:...; lonchou Electronics Design Contest

Questions about signaltap ii: I can't edit the input signal in SignalTap II, right? Usually, the clock is configured in Signal Configuration, but how can I get the correct result when analyzing the output signal? Also, what is the...; eeleader FPGA/CPLD

Shortcut: L0 L1 L2 L3 L4 L5 L6 L7 L8 L9 LA LB LC LD LE LF LG LH LI LJ LK LL LM LN LO LP LQ LR LS LT LU LV LW LX LY LZ M0 M1 M2 M3 M4 M5 M6 M7 M8 M9 MA MB MC MD ME MF MG MH MI MJ MK ML MM MN MO MP MQ MR MS MT MU MV MW MX MY MZ N0 N1 N2 N3 N4 N5 N6 N7 N8 NA NB NC ND NE NF NG NH NI NJ NK NL NM NN NO NP NQ NR NS NT NU NV NX NZ O0 O1 O2 O3 OA OB OC OD OE OF OG OH OI OJ OK OL OM ON OP OQ OR OS OT OV OX OY OZ P0 P1 P2 P3 P4 P5 P6 P7 P8 P9 PA PB PC PD PE PF PG PH PI PJ PK PL PM PN PO PP PQ PR PS PT PU PV PW PX PY PZ Q1 Q2 Q3 Q4 Q5 Q6 Q8 Q9 QA QB QC QE QF QG QH QK QL QM QP QR QS QT QV QW QX QY R0 R1 R2 R3 R4 R5 R6 R7 R8 R9 RA RB RC RD RE RF RG RH RI RJ RK RL RM RN RO RP RQ RR RS RT RU RV RW RX RY RZ

Popular Components